Installation and Operation Manual
Table Of Contents
- Contents
- 1 Introduction
- 2 IP Security
- 3 Configuration
- 3.1 Requirements
- 3.2 Access the GUI
- 3.3 GUI Web Access
- 3.4 Configure the Mobility Master
- 3.5 Configure the Standby Mobility Master
- 3.6 Configure the Pari Master
- 3.7 Configure the Standby Pari Master
- 3.8 Configure the Master
- 3.9 Configure the Standby Master
- 3.10 Plug and Play Configuration
- 3.11 Configure the Radio
- 3.12 Configure Deployment
- 3.13 Add Users
- 4 Operation
- 4.1.1 Name the IPBS and IPBL
- 4.1.2 Change User Name and Password
- 4.1.3 Centralized Management of Administrator and Auditor Accounts Using Kerberos
- 4.1.4 Configure the NTP Settings
- 4.1.5 Certificates
- 4.1.6 License
- 4.2.1 Set DHCP Mode
- 4.2.2 Set a Static IP Address
- 4.2.3 Dynamic IP address via DHCP
- 4.2.4 Link
- 4.2.5 Configure VLAN
- 4.2.6 View LAN Statistics
- 4.2.7 Enable RSTP (only for IPBL)
- 4.2.8 Deactivate LAN Port (only for IPBL)
- 4.3.1 Configure IP Settings
- 4.3.2 Routing
- 4.4.1 Configure LDAP Server
- 4.4.2 Check LDAP Server Status
- 4.4.3 Configure LDAP Replicator
- 4.4.4 Check LDAP Replicator Status
- 4.4.5 Expert tool
- 4.5.1 Change System Name and Password
- 4.5.2 Set Subscription Method
- 4.5.3 Configure Authentication Code
- 4.5.4 Select Tones
- 4.5.5 Set Default Language
- 4.5.6 Set Frequency Band
- 4.5.7 Enable Carriers
- 4.5.8 Local R-Key Handling
- 4.5.9 No Transfer on Hangup
- 4.5.10 No On-Hold Display
- 4.5.11 Display Original Called
- 4.5.12 Early Encryption
- 4.5.13 Configure Coder
- 4.5.14 Secure RTP
- 4.5.15 Configure Supplementary Services
- 4.5.16 Select Mode
- 4.5.17 Set Master Id
- 4.5.18 Enable PARI Function
- 4.5.19 Set Region Code
- 4.5.20 Configure Gatekeeper
- 4.5.21 Registration for Anonymous Devices
- 4.5.22 Conferencing Unit
- 4.5.23 Select Crypto Master Mode
- 4.5.24 Select Mobility Master Mode
- 4.5.25 Connect Mobility Master to other Mobility Master(s)
- 4.5.26 Disconnect Mobility Master from other Mobility Master(s)
- 4.5.27 Connect Mobility Master to a Crypto Master
- 4.5.28 Connect Master to a Mobility Master
- 4.5.29 Enable the Radio
- 4.5.30 Enter IP Address to the PARI Master and the Standby PARI Master
- 4.5.31 Multiple Radio Configuration
- 4.5.32 PARI
- 4.5.33 SARI
- 4.5.34 Configure Air Synchronization
- 4.6.1 Add instance id to the user registration with the IP-PBX
- 4.6.2 IP-PBX supports redirection of registration when registered to alternative proxy
- 4.6.3 Use local contact port as source port for TCP and TLS connections
- 4.6.4 Session Timer (initial value)
- 4.7.1 Configure Messaging
- 4.7.2 Device Management
- 4.7.3 Service Discovery
- 4.7.4 Send Status Log
- 4.7.5 Module Fault List
- 4.8.1 Configure Automatic Firmware Update
- 4.8.2 Configure Logging
- 4.8.3 Configure the HTTP settings
- 4.8.4 Configure the HTTP Client settings
- 4.8.5 SNMP
- 4.8.6 Phonebook
- 4.8.7 Configure IP-DECT to Connect to a Presence System Using ICP
- 4.9.1 Show all Registered Users in the IP-DECT System
- 4.9.2 Search for User Information
- 4.9.3 Add a User
- 4.9.4 Add a User Administrator
- 4.9.5 Export the Users to a csv file
- 4.9.6 Show Anonymous
- 4.10.1 Radios
- 4.10.2 RFPs
- 4.10.3 Sync Ring
- 4.10.4 Sync Ports
- 4.10.5 Air Sync
- 4.10.6 Sync Lost Counter in IPBS
- 4.11.1 Air Sync Overview
- 4.11.2 Disturbances
- 4.11.3 Status
- 4.12.1 Display All Ongoing Calls in the System
- 4.12.2 Display Calls
- 4.12.3 Handover
- 4.13.1 General
- 4.13.2 Interfaces
- 4.13.3 SIP Interfaces
- 4.13.4 Gatekeeper Interfaces
- 4.13.5 Routes – Configuration
- 4.13.6 Show Active Calls
- 4.15.1 Before Upgrading
- 4.15.2 Upgrading Sequence
- 4.15.3 Software Upgrade from 2.X.X
- 4.15.4 Software Upgrade
- 4.15.5 Configuration After Updating the Firmware From Software Version 2.X.X to Later
- 4.15.6 Configuration After Updating the Firmware From Software Version 3.X.X to Later
- 4.22.1 Update Configuration
- 4.22.2 Update Firmware
- 4.22.3 Update the Boot File
- 4.22.4 Update the RFPs
- 4.27.1 Logging
- 4.27.2 Tracing
- 4.27.3 Alarms
- 4.27.4 Events
- 4.27.5 Performance
- 4.27.6 Config Show
- 4.27.7 Ping
- 4.27.8 Traceroute
- 4.27.9 Environment
- 4.27.10 RFP Scan
- 4.27.11 Service Report
- 4.28.1 Idle Reset
- 4.28.2 Immediate Reset
- 4.28.3 TFTP Mode
- 4.28.4 Boot
- 5 Commissioning
- 6 Troubleshooting
- 7 Related Documents
- Document History
- Appendix A: How to Configure and Use the Update Server
- Appendix B: Local R-Key Handling
- Appendix C: Database Maintenance
- Appendix D: Load Balancing
- Appendix E: Update Script for Configuration of Kerberos Clients
- Appendix F: Install Certificate in the Web Browser
- Appendix G: Used IP Ports
- Appendix H: Configure DHCP Options
TD 92579EN
10 April 2015 / Ver. N
Installation and Operation Manual
IP-DECT Base Station & IP-DECT Gateway (software version 7.2.X)
108
When upgrading from software version 2.X.X to later: Update configuration of
Master, see
4.15.5 Configuration After Updating the Firmware From Software
Version 2.X.X to Later.
When upgrading from software version 3.X.X to later: Update configuration of
Master, see
4.15.6 Configuration After Updating the Firmware From Software
Version 3.X.X to Later.
4.15.3 Software Upgrade from 2.X.X
1 When upgrading from software version 2.X.X to later: Disable LDAP replication for
all Radios except in the case of Standby Master to Master Replication. Select LDAP >
Replicator and make sure that the Enable check box is not selected.
2 Only for IPBL: When upgrading from software version 2.X.X to later: Update the
boot file to 413. See
4.22.3 Update the Boot File for more information on how to
update the boot file.
3 When upgrading from software version 2.X.X to later: Update the firmware to
2.4.0 or later 2.X.X. See
4.22.2 Update Firmware for more information on how to
update the firmware.
4 Reset in order to make the changes take effect, see 4.28 Reset.
5 Update the firmware to 3.4.12. See 4.22.2 Update Firmware for more information
on how to update the firmware.
6 Reset in order to make the changes take effect, see 4.28 Reset.
7 Update the boot file to 3.0.26. See 4.22.3 Update the Boot File for more
information on how to update the boot file.
8 Reset in order to make the changes take effect, see 4.28 Reset.
9 To update the IPBS Web GUI, press CTRL+F5 on the keyboard or close the IPBS Web
GUI and start it again in order to update the GUI.
10 Continue with 4.15.4 Software Upgrade.
4.15.4 Software Upgrade
1 Update the firmware to the latest. See 4.22.2 Update Firmware for more
information on how to update the firmware.
2 Update the boot file to the latest. See 4.22.3 Update the Boot File for more
information on how to update the boot file.
3 Reset in order to make the changes take effect, see 4.28 Reset.
4 To update the IPBS Web GUI, press CTRL+F5 on the keyboard or close the IPBS Web
GUI and start it again in order to update the GUI.
4.15.5 Configuration After Updating the Firmware From Software Version 2.X.X to
Later
The following configuration settings should be changed in the Web GUI after updating
the firmware from version 2.X.X to later.
Radio Configuration
1 Select DECT > Radio and enter the name and password for the Pari Master.
2 Reset in order to make the changes take effect, see 4.28 Reset.