Technical Product Manual - DCT1800-GAP Safety and regulatory information Section 1 Safety and regulatory information TD 92093 (1/LZBNB 103 108 R4D) / 2005-11-07/ Ver.
Technical Product Manual - DCT1800-GAP Safety and regulatory information TD 92093 (1/LZBNB 103 108 R4D) / 2005-11-07/ Ver.
Technical Product Manual - DCT1800-GAP Safety and regulatory information, Table of contents Table of contents Page Chapter 1 Introduction .................................................................................................. 1 Chapter 2 Safety ............................................................................................................. 3 2.1 2.2 2.3 Safety rules.................................................................................................................
Technical Product Manual - DCT1800-GAP Safety and regulatory information, Table of contents IV TD 92093 (1/LZBNB 103 108 R4D) / 2005-11-07/ Ver.
Technical Product Manual - DCT1800-GAP Safety and regulatory information, Introduction Chapter 1 Introduction This section contains important safety and regulatory information. Other sections refer to this section when applicable.
Technical Product Manual - DCT1800-GAP Safety and regulatory information, Introduction 2 TD 92093GB (1/LZBNB 103 108 R4D) / 2005-11-07/ Ver.
Technical Product Manual - DCT1800-GAP Safety and regulatory information, Safety Chapter 2 2.1 Safety Safety rules • Ensure that the voltage and frequency of the mains power socket matches the voltage and frequency inscribed on the equipment’s electrical rating label. • Never install telephone wiring during a thunderstorm. • Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations.
Technical Product Manual - DCT1800-GAP Safety and regulatory information, Safety 2.2 • Torque power supply terminal block screws to 7 in. - lbs • For the safety status of the different interconnection points of the system refer to ‘‘ on page 8. Safety symbols For your protection and to avoid damage to the DCT1800-GAP system you will find stickers where applicable. The stickers have the following symbols and meaning: Caution Read and follow the safety rules and warning messages in this manual.
Technical Product Manual - DCT1800-GAP Safety and regulatory information, Safety ATTENTION! IL Y A DANGER D’EXPLOSION S’IL Y A REMPLACEMENT INCORRECT DE LA BATTERIE. REMPLACER UNIQUEMENT AVEC UNE BATTERIE DU MÊME TYPE OU D’UN TYPE RECOMMANDÉ PAR LE CONSTRUCTEUR. METTRE AU RÉBUT LES BATTERIES USAGÉES CONFORMÉMENT AUX INSTRUCTIONS DU FABRICANT. VARNING! EXPLOSIONSFARA VID FELAKTIGT BATTERIBYTE.
Technical Product Manual - DCT1800-GAP Safety and regulatory information, Safety ADVARSEL! LITHIUMBATTERI – EKSPLOSJONSFARE. VED UTSKIFTING BENYTTES KUN BATTERI SOM ANBEFALT AV APPARATFABRIKANTEN. BRUKT BATTERI RETURNERES APPARATLEVERANDOREN. 6 TD 92093GB (1/LZBNB 103 108 R4D) / 2005-11-07/ Ver.
Technical Product Manual - DCT1800-GAP Safety and regulatory information, Protection against electrostatic discharge (ESD) Chapter 3 3.1 Protection against electrostatic discharge (ESD) General Integrated circuits are sensitive to ESD. To avoid damage caused by ESD, service engineers and other people must handle equipment and boards carefully. Electronic equipment has become more resistive to ESD, but we see an increase of situations where static electricity can build up.
Technical Product Manual - DCT1800-GAP Safety and regulatory information, Protection against electrostatic discharge (ESD) PROTECT ESD SENSITIVE DEVICES Boards with static sensitive devises can be recognized by the sign. Observe special handling rules. Exchanging system boards requires a grounded wrist strap Some of the benefits of protection are: - less failures/service calls, - reduced maintenance costs, - high customer satisfaction.
Technical Product Manual - DCT1800-GAP Safety and regulatory information, Safety aspects of the DCT1800-GAP system Chapter 4 Safety aspects of the DCT1800-GAP system The DCT1800-GAP system meets the safety standards EN41003 and EN60950/IEC950. The system is a pluggable equipment class A according to EN60950/IEC950. The system is class I equipment, with class II insulation between primary and secondary circuits. Connection to protective earth is necessary for safety reasons.
Technical Product Manual - DCT1800-GAP Safety and regulatory information, Safety aspects of the DCT1800-GAP system 10 TD 92093GB (1/LZBNB 103 108 R4D) / 2005-11-07/ Ver.
Technical Product Manual - DCT1800-GAP Safety and regulatory information, Legal restrictions for the Line Termination Unit, LTU Chapter 5 5.1 Legal restrictions for the Line Termination Unit, LTU – REX-BRD0019 Line Termination Unit, LTU – REX-BRD0019 (ROFNB 157 25/2) The table below gives an overview of where LTU REX-BRD0019 (ROFNB 157 25/2) can be used. As can be observed it can be used in most cases.
Technical Product Manual - DCT1800-GAP Safety and regulatory information, Legal restrictions for the Line Termination Unit, LTU 12 TD 92093GB (1/LZBNB 103 108 R4D) / 2005-11-07/ Ver.
Technical Product Manual - DCT1800-GAP Safety and regulatory information, Standards and Regulations for US Chapter 6 6.1 Standards and Regulations for US Standards and Regulations The DCT1800 System adheres to the following standards and regulations: 6.2 6.3 • FCC Part 15 • IEC 60950-1 • UL 60950 • UTAM, Inc. • ANSI/IEEE C95.
Technical Product Manual - DCT1800-GAP Safety and regulatory information, Standards and Regulations for US 6.4 Regulatory Compliance Statements FCC CLASS B NOTICE This equipment complies with part 15 of the FCC rules. Operation is subject to the following conditions: 1) This equipment may not cause harmful interference, and 2) This equipment must accept any interference received, including interference that may cause undesired operation.
Technical Product Manual - DCT1800-GAP Safety and regulatory information, Standards and Regulations for US The term “IC:” before the radio certification number only signifies that industry of canada technical specification were met. DO NOT TAMPER WITH THE WARRANTY SEAL ON THE BACK OF YOUR PHONE. TAMPERING WITH THIS SEAL CAN VOID YOUR WARRANTY. DO NOT ATTEMPT TO TAKE YOUR PHONE APART. DOING SO WILL VOID YOUR WARRANTY. YOUR PHONE DOES NOT CONTAIN CONSUMER SERVICEABLE COMPONENTS.
Technical Product Manual - DCT1800-GAP Safety and regulatory information, Standards and Regulations for US EXPOSURE TO RADIO FREQUENCY SIGNALS (SAR) The wireless phone is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limit for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the US government and Canada.
Technical Product Manual - DCT1800-GAP Safety and regulatory information, CE-marking Chapter 7 7.1 CE-marking General A number of DCT1800-GAP products are CE-marked.
Technical Product Manual - DCT1800-GAP Safety and regulatory information, CE-marking TD 92093GB (1/LZBNB 103 108 R4D) / 2005-11-07/ Ver.