User manual
Table Of Contents
- Contents
- 1 Introduction
- 2 Descriptions
- 3 Menu Tree
- 4 Basic Operation
- 5 Calling
- 5.1 Open the Call List
- 5.2 Incoming Call
- 5.3 Outgoing Call
- 5.3.1 Pre-Dial
- 5.3.2 Post-Dial with Headset Button
- 5.3.3 Dial Using a Pre-programmed Number
- 5.3.4 Dial a Number from the Call list
- 5.3.5 Dial Last Called Number with Headset Button
- 5.3.6 Dial the Sender of a Message
- 5.3.7 Dial a Number from Contacts
- 5.3.8 Dial a Name from the Central Phonebook
- 5.3.9 Dial a Number from the Company Phonebook
- 5.4 During a Call
- 5.4.1 Adjust the Volume during a Call
- 5.4.2 Open Contacts during the Call
- 5.4.3 Open Messaging Menu during a Call
- 5.4.4 Turn the Microphone On or Off during a Call
- 5.4.5 Lock and Unlock the Keypad during a Call
- 5.4.6 Audio Transfer
- 5.4.7 Start a New Call during Conversation
- 5.4.8 Switch between Calls
- 5.4.9 End a Call
- 5.4.10 Transfer a Call
- 5.4.11 Transfer to New Call
- 5.4.12 Conference Call
- 5.4.13 Call Back
- 5.4.14 Send Call Waiting
- 5.4.15 Answering Call Waiting
- 5.4.16 DTMF
- 5.4.17 DECT Info
- 5.4.18 Send Data
- 5.5 Loudspeaking Function
- 5.6 Call Diversion
- 5.7 Emergency Calls
- 6 Messaging
- 6.1 Mini Messaging
- 6.2 Message List
- 6.3 Receive a Message
- 6.3.1 Read a Stored Message
- 6.3.2 Reply to a Message
- 6.3.3 Delete Messages
- 6.3.4 Forward a Message
- 6.3.5 Call the Sender of the Message
- 6.3.6 Call a Number Included in a Message
- 6.3.7 Save Number
- 6.3.8 Message Templates
- 6.3.9 Write and Send a Message
- 6.3.10 Open a Sent Message
- 6.3.11 Send to Another Destination
- 6.3.12 Review Inbox Content while Reading a Message
- 6.4 Receive a Message with Request for Answer
- 6.5 Message Queuing and Message Priority
- 6.6 Message Priority and Call Priority
- 6.7 Interactive Messaging
- 6.8 Message Indication Repetition
- 6.9 Colored Messaging
- 6.10 Decline a Call with a Predefined Message
- 6.11 Answering a Text Message with a Predefined Message
- 6.12 Calling while Reading a Text Message
- 6.13 Mobile Data
- 6.14 Send Data with Bluetooth Barcode Reader
- 6.15 Voicemail
- 7 Alarm Operation
- 8 Menu Operation
- 9 Procedure Call
- 10 System Profiles
- 11 Advanced Functions
- 12 System Handling
- 13 Troubleshooting
- 14 Operation Notice
- 15 Maintenance
- 16 Related Documents
- 17 Document History
- Appendix A: Bluetooth Headset
- Appendix B: Bluetooth Barcode Reader
- Index
TD 92477EN
31 October 2013 / Ver. J
User Manual
Ascom d62 DECT Handset
79
14 Operation Notice
14.1 Accessibility and Voice Quality
The base network is not always available. If you do not get in contact with your system,
contact your system administrator. For best voice quality, avoid positioning near computer,
radio or similar equipment.
Operating Area
The handset can only be used in the area covered by the system. Outside of this are
a
the
handset looses contact with the system. The signal strength icon is low and “Searching” is
displayed.
Out of Range
When the handset leaves the system's coverage area
a sh
ort beep sounds and the text
“Searching” is displayed.
The out of range beep is repeated every minute for 30 minutes. Th
e sound can be turned off
by long pressing
, or .
When re-entering the coverage area it can take a couple of mi
nutes before the handset is
automatically registered with the system.