User manual
Table Of Contents
- Contents
- 1 Introduction
- 2 Descriptions
- 3 Menu Tree
- 4 Basic Operation
- 5 Calling
- 5.1 Open the Call List
- 5.2 Incoming Call
- 5.3 Outgoing Call
- 5.3.1 Pre-Dial
- 5.3.2 Post-Dial with Headset Button
- 5.3.3 Dial Using a Pre-programmed Number
- 5.3.4 Dial a Number from the Call list
- 5.3.5 Dial Last Called Number with Headset Button
- 5.3.6 Dial the Sender of a Message
- 5.3.7 Dial a Number from Contacts
- 5.3.8 Dial a Name from the Central Phonebook
- 5.3.9 Dial a Number from the Company Phonebook
- 5.4 During a Call
- 5.4.1 Adjust the Volume during a Call
- 5.4.2 Open Contacts during the Call
- 5.4.3 Open Messaging Menu during a Call
- 5.4.4 Turn the Microphone On or Off during a Call
- 5.4.5 Lock and Unlock the Keypad during a Call
- 5.4.6 Audio Transfer
- 5.4.7 Start a New Call during Conversation
- 5.4.8 Switch between Calls
- 5.4.9 End a Call
- 5.4.10 Transfer a Call
- 5.4.11 Transfer to New Call
- 5.4.12 Conference Call
- 5.4.13 Call Back
- 5.4.14 Send Call Waiting
- 5.4.15 Answering Call Waiting
- 5.4.16 DTMF
- 5.4.17 DECT Info
- 5.4.18 Send Data
- 5.5 Loudspeaking Function
- 5.6 Call Diversion
- 5.7 Emergency Calls
- 6 Messaging
- 6.1 Mini Messaging
- 6.2 Message List
- 6.3 Receive a Message
- 6.3.1 Read a Stored Message
- 6.3.2 Reply to a Message
- 6.3.3 Delete Messages
- 6.3.4 Forward a Message
- 6.3.5 Call the Sender of the Message
- 6.3.6 Call a Number Included in a Message
- 6.3.7 Save Number
- 6.3.8 Message Templates
- 6.3.9 Write and Send a Message
- 6.3.10 Open a Sent Message
- 6.3.11 Send to Another Destination
- 6.3.12 Review Inbox Content while Reading a Message
- 6.4 Receive a Message with Request for Answer
- 6.5 Message Queuing and Message Priority
- 6.6 Message Priority and Call Priority
- 6.7 Interactive Messaging
- 6.8 Message Indication Repetition
- 6.9 Colored Messaging
- 6.10 Decline a Call with a Predefined Message
- 6.11 Answering a Text Message with a Predefined Message
- 6.12 Calling while Reading a Text Message
- 6.13 Mobile Data
- 6.14 Send Data with Bluetooth Barcode Reader
- 6.15 Voicemail
- 7 Alarm Operation
- 8 Menu Operation
- 9 Procedure Call
- 10 System Profiles
- 11 Advanced Functions
- 12 System Handling
- 13 Troubleshooting
- 14 Operation Notice
- 15 Maintenance
- 16 Related Documents
- 17 Document History
- Appendix A: Bluetooth Headset
- Appendix B: Bluetooth Barcode Reader
- Index
TD 92477EN
31 October 2013 / Ver. J
User Manual
Ascom d62 DECT Handset
77
Error or Warning Messages
Display shows Probable cause Action or comment
No access The network is in range, but no
acc
ess rights.
Switch handset off and then
switch it on again or contact
system administrator.
No System. The handset
beeps once a minute
(du
ring max 30
minutes) with a low
tone followed by a high
tone (if enabled, the
vibrator also follows the
beeps).
The handset is out of coverage or
han
dset is defective.
Stop the beep with the Sound
off key and go into range.
Note: When re-entering the
coverage area it can tak
e a
couple of minutes before the
handset automatically has
registered into the system.
or
contact system administrator.
The message Failed is
displayed when the
handset trie
s to
download an ECG
waveform image.
The IP-DECT wireless connection
p
oint is overloaded with too many
calls.
Go see the patient. The ECG
Monitoring functionality starts
working when the IP-DECT
connection point is no longer
overloaded.
SERVICE NEEDED
Parameters corrupt
Note: This display
me
ssage is only shown
in English.
The handset is defective. Select the reset option on the
m
iddle soft key and upgrade
the handset’s software to
version 3.0.0 or greater. If this
is not available or the problem
persists send the handset for
service.
SERVICE NEEDED
Invalid IPDI
Note: This display
me
ssage is only shown
in English.
Easy replacement procedure not
f
ollowed correctly or failure during
easy replacement procedure.
Send the handset for service.
Enter PIN code The handset’s lock is activated. Enter the required PIN code. If
PIN code lost enter new vi
a PDM
or do a factory reset via PDM.
Battery low, charge now The battery level is low. Charge or replace the battery.
Phonebook is not
availa
ble at the
moment.
The phonebook does not respond,
not available at the moment.
Try again later or if fault
persists do a factory reset via
admin menu or PDM.
Voicemail number not
defined
There is no Voicemail number
defined in the handset.
Define a Voicemail number via
PDM.