User manual
Table Of Contents
- Contents
- 1 Introduction
- 2 Descriptions
- 3 Menu Tree
- 4 Basic Operation
- 5 Calling
- 5.1 Open the Call List
- 5.2 Incoming Call
- 5.3 Outgoing Call
- 5.3.1 Pre-Dial
- 5.3.2 Post-Dial with Headset Button
- 5.3.3 Dial Using a Pre-programmed Number
- 5.3.4 Dial a Number from the Call list
- 5.3.5 Dial Last Called Number with Headset Button
- 5.3.6 Dial the Sender of a Message
- 5.3.7 Dial a Number from Contacts
- 5.3.8 Dial a Name from the Central Phonebook
- 5.3.9 Dial a Number from the Company Phonebook
- 5.4 During a Call
- 5.4.1 Adjust the Volume during a Call
- 5.4.2 Open Contacts during the Call
- 5.4.3 Open Messaging Menu during a Call
- 5.4.4 Turn the Microphone On or Off during a Call
- 5.4.5 Lock and Unlock the Keypad during a Call
- 5.4.6 Audio Transfer
- 5.4.7 Start a New Call during Conversation
- 5.4.8 Switch between Calls
- 5.4.9 End a Call
- 5.4.10 Transfer a Call
- 5.4.11 Transfer to New Call
- 5.4.12 Conference Call
- 5.4.13 Call Back
- 5.4.14 Send Call Waiting
- 5.4.15 Answering Call Waiting
- 5.4.16 DTMF
- 5.4.17 DECT Info
- 5.4.18 Send Data
- 5.5 Loudspeaking Function
- 5.6 Call Diversion
- 5.7 Emergency Calls
- 6 Messaging
- 6.1 Mini Messaging
- 6.2 Message List
- 6.3 Receive a Message
- 6.3.1 Read a Stored Message
- 6.3.2 Reply to a Message
- 6.3.3 Delete Messages
- 6.3.4 Forward a Message
- 6.3.5 Call the Sender of the Message
- 6.3.6 Call a Number Included in a Message
- 6.3.7 Save Number
- 6.3.8 Message Templates
- 6.3.9 Write and Send a Message
- 6.3.10 Open a Sent Message
- 6.3.11 Send to Another Destination
- 6.3.12 Review Inbox Content while Reading a Message
- 6.4 Receive a Message with Request for Answer
- 6.5 Message Queuing and Message Priority
- 6.6 Message Priority and Call Priority
- 6.7 Interactive Messaging
- 6.8 Message Indication Repetition
- 6.9 Colored Messaging
- 6.10 Decline a Call with a Predefined Message
- 6.11 Answering a Text Message with a Predefined Message
- 6.12 Calling while Reading a Text Message
- 6.13 Mobile Data
- 6.14 Send Data with Bluetooth Barcode Reader
- 6.15 Voicemail
- 7 Alarm Operation
- 8 Menu Operation
- 9 Procedure Call
- 10 System Profiles
- 11 Advanced Functions
- 12 System Handling
- 13 Troubleshooting
- 14 Operation Notice
- 15 Maintenance
- 16 Related Documents
- 17 Document History
- Appendix A: Bluetooth Headset
- Appendix B: Bluetooth Barcode Reader
- Index
TD 92477EN
31 October 2013 / Ver. J
User Manual
Ascom d62 DECT Handset
25
5.3 Outgoing Call
5.3.1 Pre-Dial
Enter the number and press
to get the line. The number is displayed while dialling. The
Soft key "Clear" can be pressed to erase the number if required. Th
e navigation key can be
used to step, add or delete digits from the middle of a number.
An international number can be dialled from the handse
t by entering a + character followed
by the country code and local number. To enter the + character, long press the 0 key until
the character is shown in the display.
NOTE: The + character cannot be entered and internat
ional num
bers cannot de dialled in the
following circumstances:
• If the 0 key has been configured as a hot key.
• If the handset has been set up to perform advan
c
ed functions normally used by a system
administrator, as described in 11.1 Admin Menu on pa
ge 73.
5.3.2 Post-Dial with Headset Button
The headset button can be used to obtain a dial tone and dial a num
ber. However, the
headset must have been configured via the PDM/Device Manager to allow this.
5.3.3 Dial Using a Pre-programmed Number
Note: The Multi
function button is applicable for d62 Talker and d62 Messenger only.
A Navigation key, Hot key, Soft key or
Multifunction button
can be programmed with a
handset number, as described in section 3.6 Shortcuts on pa
ge 17. A headset button
can
also be programmed with a handset number as long as it has been configured by the
administrator via the P
DM/Device Manager.
To dial a pre-programmed number, press the pre-program
med key or button. The call is
connected automatically.
5.3.4 Dial a Number from the Call list
1Press
.
2 Select a number press
or soft key "Call" to dial. The number can be edited before
the call is started. Press "More" and select "Edit number".
5.3.5 Dial Last Called Number with Headset Button
If a headset is used, the headset button can be used to
dial the last called number. However,
the headset must have been configured via the PDM/Device Manager to allow this.
5.3.6 Dial the Sender of a Message
You can call the sender of a message stored in the message list, from the Me
ssaging menu.
1 Open the menu by pressing the confirmation button, or the soft
key "Menu".
2 Select "Messaging".
3 Select "Inbox".
4 Select message from the list.
5 Select "View".
6 Select "More".