User manual
Table Of Contents
- Contents
- 1 Introduction
- 2 Descriptions
- 3 Menu Tree
- 4 Basic Operation
- 5 Calling
- 5.1 Open the Call List
- 5.2 Incoming Call
- 5.3 Outgoing Call
- 5.3.1 Pre-Dial
- 5.3.2 Post-Dial with Headset Button
- 5.3.3 Dial Using a Pre-programmed Number
- 5.3.4 Dial a Number from the Call list
- 5.3.5 Dial Last Called Number with Headset Button
- 5.3.6 Dial the Sender of a Message
- 5.3.7 Dial a Number from Contacts
- 5.3.8 Dial a Name from the Central Phonebook
- 5.3.9 Dial a Number from the Company Phonebook
- 5.4 During a Call
- 5.4.1 Adjust the Volume during a Call
- 5.4.2 Open Contacts during the Call
- 5.4.3 Open Messaging Menu during a Call
- 5.4.4 Turn the Microphone On or Off during a Call
- 5.4.5 Lock and Unlock the Keypad during a Call
- 5.4.6 Audio Transfer
- 5.4.7 Start a New Call during Conversation
- 5.4.8 Switch between Calls
- 5.4.9 End a Call
- 5.4.10 Transfer a Call
- 5.4.11 Transfer to New Call
- 5.4.12 Conference Call
- 5.4.13 Call Back
- 5.4.14 Send Call Waiting
- 5.4.15 Answering Call Waiting
- 5.4.16 DTMF
- 5.4.17 DECT Info
- 5.4.18 Send Data
- 5.5 Loudspeaking Function
- 5.6 Call Diversion
- 5.7 Emergency Calls
- 6 Messaging
- 6.1 Mini Messaging
- 6.2 Message List
- 6.3 Receive a Message
- 6.3.1 Read a Stored Message
- 6.3.2 Reply to a Message
- 6.3.3 Delete Messages
- 6.3.4 Forward a Message
- 6.3.5 Call the Sender of the Message
- 6.3.6 Call a Number Included in a Message
- 6.3.7 Save Number
- 6.3.8 Message Templates
- 6.3.9 Write and Send a Message
- 6.3.10 Open a Sent Message
- 6.3.11 Send to Another Destination
- 6.3.12 Review Inbox Content while Reading a Message
- 6.4 Receive a Message with Request for Answer
- 6.5 Message Queuing and Message Priority
- 6.6 Message Priority and Call Priority
- 6.7 Interactive Messaging
- 6.8 Message Indication Repetition
- 6.9 Colored Messaging
- 6.10 Decline a Call with a Predefined Message
- 6.11 Answering a Text Message with a Predefined Message
- 6.12 Calling while Reading a Text Message
- 6.13 Mobile Data
- 6.14 Send Data with Bluetooth Barcode Reader
- 6.15 Voicemail
- 7 Alarm Operation
- 8 Menu Operation
- 9 Procedure Call
- 10 System Profiles
- 11 Advanced Functions
- 12 System Handling
- 13 Troubleshooting
- 14 Operation Notice
- 15 Maintenance
- 16 Related Documents
- 17 Document History
- Appendix A: Bluetooth Headset
- Appendix B: Bluetooth Barcode Reader
- Index
TD 92477EN
31 October 2013 / Ver. J
User Manual
Ascom d62 DECT Handset
99
B.9 Troubleshooting
Problem Reason Solution
No barcode reader found Barcode reader is turned
off
Turn on barcode reader
1
1. For additional information, see the Manual for the Bluetooth barcode reader
Barcode reader is out of
battery
Charge barcode reader
1
Barcode reader is out of
range
Move barcode reader closer to
handset
< 10 metre.
Barcode reader is not in
pairing mode
Turn barcode reader into pairing
mode
1
Pairing fails Barcode reader is not in
pairing mode
Turn barcode reader into pairing/
discoverable mode
1
Incorrect PIN entered Try again and enter correct PIN
1
Connecting fails/Failed to
connect barcode reader
Barcode reader is not
turned on
Turn on barcode reader
1
Barcode reader is out of
range
Move barcode reader closer to
handset
Link key in barcode reader
has been deleted
Repeat pairing procedure
1
Barcode reader is already
connected to another
handset
Disconnect barcode reader from the
other handset
Too close to disturbing
devices.
Disturbing devices can be WLAN
equipment, microwave etc.
Barcode reader can not
connect to handset (see
barcode reader manual
for details on how to
connect)
Handset is not turned on Turn on handset
Bluetooth module is
disabled
Enable Bluetooth in Bluetooth menu
Another barcode reader is
already connected to the
handset
Disconnect the connected barcode
reader
Link key is missing in
either barcode reader or
handset.
Repeat pairing procedure
1
Too close to disturbing
devices.
Disturbing devices can be WLAN
equipment, microwave etc.
Other faults/or if the
solutions do not work.
1) Switch the handset and barcode
reader
1
on and off. For additional
information, see
2) Perform a factory reset on the
barcode reader
1
.