User`s guide

ManualsBrandsAscend ManualsComputer equipmentPipeline

181

182

183

184

185

186

187

188

189

190

Table Of Contents

Ascend Customer Service
How to use this guide
What you should know
Documentation conventions
How to use the on-board software
- Changing parameter values
- Saving or discarding your changes
Manual set
Configuring WAN Connections
- About Wide Area Network (WAN) connections
- Link encapsulation
- Nailed groups
- How calls are initiated
- How calls are answered
- Data compression options
- The Answer profile
- Connection profiles
- Configuring Frame Relay connections
Configuring IP Routing
- Introduction to IP routing on the Pipeline
- Managing the routing table
- Configuring IP routing connections
- Ascend Tunnel Management Protocol (ATMP)
IP Address Management
- Connecting to a local IP network
- BOOTP Relay
- DHCP services
  - How IP addresses are assigned
  - Configuring DHCP services
- Dial-in user DNS server assignments
  - Configuring DNS servers in the Ethernet profile
  - Configuring DNS servers in the Connection profile
- Local DNS host address table
- Network Address Translation (NAT) for a LAN
Configuring IPX Routing
- How the Pipeline performs IPX routing
- Adding the Pipeline to the local IPX network
- Working with the RIP and SAP tables
- Configuring IPX routing connections
Configuring the Pipeline as a Bridge
- Introduction to Ascend bridging
- Enabling bridging
- Managing the bridge table
- Configuring bridged connections
Defining Filters and Firewalls
- Introduction to filters
- Overview of Filter profiles
- Example filters
- Working with predefined call filters
- Display unwanted dial-out packets
- Secure Access Firewalls
- Filter persistence
  - Background on firewall and filter persistence
  - Filter persistence and Connection profiles
Setting Up Pipeline Security
- Recommended security measures
- Pipeline Security profiles
- Connection security
- Using filters to secure the network
- Using security cards
Pipeline System Administration
- Overview of administration functions
- Activating administrative privileges
- Configuring administration options
- Using the Pipeline status windows
- Performing system administration operations
- Using the terminal server interface
  - Invoking and quitting the terminal server interfac...
  - Terminal server commands
- Accessing a local Pipeline via Telnet
Pipeline 75 Voice Features
- About the integrated services of ISDN
- How your ISDN service affects voice features
  - Ordering supplementary voice services
  - Ordering voice features
- How outgoing voice calls are handled
- How incoming voice calls are handled
- Support for 2-channel calls on one SPID
  - Configuring a 2-channel, single SPID call
- Support for outgoing 3.1K audio calls
  - How 3.1K audio calls work
  - Configuring 3.1K audio call
- EAZ Terminal ID for Germany
IDSL Implementations
- ISDN Digital Subscriber Line (IDSL)
- Configuring an IDSL connection
- Making voice calls over IDSL
APP Server utility
- About the APP Server utility
- APP Server installation and setup
Troubleshooting
- Cabling problems: Rule these out first
- Common problems and their solutions
- Problems configuring the Pipeline
- ISDN BRI interface problems
  - Bridge/router problems
- Problems accessing the remote network
  - Check the installation
  - Configuration problems
Upgrading system software
- What you need to upgrade system software
- Displaying the software load name
- The upgrade procedure
Untitled

Defining Filters and Firewalls

Example filters

Pipeline User’s Guide Preliminary January 30, 1998 6-13

Assign a name to the Filter profile.

For example:

Name=AppleTalk Data

Open the Output Filters submenu.

Open Out filter 01 and set Valid=Yes and Type=GENERIC.

For example:

>Valid=Yes

Type=GENERIC

Generic...

IP...

IPX...

Open the Generic submenu and specify the following conditions:

Generic...

>Forward=No

Offset=14

Length=8

Mask=ffffffffffffffff

Value=aaaa0300000080f3

Compare=Equals

More=No

These conditions define a location within a packet and the hexadecimal

value that AARP packets contain within that location, protocol type 0x80f3.

Outbound AARP packets will not be forwarded.

Close Out filter 01, and then open Out filter 02.

Set Valid=Yes and Type=GENERIC, and then open the Generic submenu

and specify the following conditions:

Generic...

>Forward=Yes

Offset=14

Length=8

Mask=ffffffffffffffff

Value=aaaa03080007809b

Compare=NotEquals

More=No