™ NCS40T Trailer Control and Monitoring system Installation and Operation Manual Patent # US 9,679,735
NCS40T Important Safety Information Read the iN-Command Manual, and these warnings and instructions carefully before using this product. Failure to follow the use instructions in this owner’s manual, or improper use of the Mobile Application, Display Commander and/or Body Control Module, could result in personal injury, including death. Do not operate while vehicle is being driven. The Mobile Application, Display Commander and/or Body Control Module should not be used while the vehicle is being driven.
NCS40T • Table Of Contents Introduction ..............................................................................5 Thank You! .........................................................................5 Feature Description ...........................................................5 Precautions ........................................................................5 Packing List ........................................................................5 Installation and Mounting instruction .............
NCS40T • Introduction • Packing List • Thank You! (1) Control System Thank you for choosing iN-Command. We hope you will find the instructions in this owner’s manual clear and easy to follow. If you take a few minutes to look through it, you’ll learn how to use all the features of your new NCS40T for maximum enjoyment.
NCS40T • Installation and Mounting instruction • Mounting the NCS40T It’s a good idea to read all of the instructions before beginning the installation. • Tools and Supplies You will need these tools and supplies to install your NCS40T : • 7/16” socket with ratchet – or 7/16 wrench • 1/4” drill/bit and drill • 3/4” hole saw for mounting BT antenna • Four ¼” bolts. Length determined by material thickness you are mounting to. • Four ¼” lock nuts.
• Wiring #1 .RUNNING LIGHT OUT (BROWN L1) #2 .RIGHT LIGHT OUT (GREEN L3) #3 .EMPTY 4 2 4 1 2 1 3 4 6 5 2 3 2 1 1 #4 .HYD DOWN OUT (GREEN) #3 .SOLDENOID POWER OUT (WHITE ) #2 .TPMS POWER + (RED) 3 2 1 4 5 6 #4. EMPTY 3 #6. TRUCK POWER - (WHITE) #5 . DC 12V ( YELLOW L2) #3. TRUCK POWER+12V(RED ) #2. DC12V (GREEN L3) #4 .EMPTY #5 .LEFT LIGHT OUT (YELLOW L2) #1. DC 12V (BROWN L1) #6 .
NCS40T • Travel Lock out information (Safety) iN∙Command ® Control Systems use travel-lock-out technology to disable any functions that are deemed unsafe when the vehicle is in motion.
NCS40T • Mobile Devices iN•Command ASA Electronics, LLC The iN-Command Trailer Control System requires a mobile app to operate the system. Visit the Google Play and Apple App stores on your mobile device to download and use the iN-Command Trailer App. Only one device can be actively paired to the iN-Command Trailer Control System at a time. To use another device, the active device needs to shut down its iNCommand App to allow another device to pair.
NCS40T • Pairing A Mobile Device Click " Pair " button to enter discovery mode.( Long press " Pair " button for 5-8 seconds to disconnect device.) PAIR BUTTON PAIR INDICATOR POWER INDICATOR • iOS Pairing Instructions 1. Enable "Bluetooth" in the system settings of the mobile device. 2. Press "Pair" on the mobile device.
NCS40T 3. The DC will be displayed on the mobile device list in the format NCS40TXXXXX. 4. The mobile device now shows that the DC is connected.
NCS40T • Android Pairing Instructions 1. From the App Home Page select settings. 2. Select the "Bluetooth" tab 12 3. Press Scan to start scanning for Unpaired devices. Select the device by pressing it.
NCS40T 4. A Bluetooth pairing request will appear on the mobile device. 5. Press " Pair " on the mobile device. 6. The mobile device will be displayed in the "Paired devices " list on the mobile App.
NCS40T • Passcode Protection A passcode is required to access the system. The first time the App is opened, the user is required to enter and confirm a new passcode. • App Configuration The iN-Command Trailer App is configurable. The user can select which functions are populated on the home page. Select the Settings icon at the bottom of the home page, then press the Configuration tab. The default configuration is Battery, Hydraulic and Light Check.
NCS40T • Adding Auxiliary Function The iN-Command Trailer App is configurable. The user can select which functions are populated on the home page. Select the Settings icon at the bottom of the home page, then press the Configuration tab. The default configuration is Battery, Hydraulic and Light Check. To select or deselect an item, press on the circle next to the function. When an item is selected, the circle is hightled blue.
NCS40T • Adding TPMS If the user has iN-Command TPMS Sensors installed on the trailer, a TPMS icon can be added to the home page to provide a quick link to the iNCommand TPMS App. In the Settings page, select the Apps tab. Once in the App page, there is a selection for tires. There is an info icon that provides a descreption of the TPMS function and a link to the iN-Command TPMS App on the App store, if the user currently does not have the iNCommand TPMS App installed on their device.
NCS40T • Low Battery Voltage Alert The iN-Command Trailer App is equipped with a Low Voltage Alert. If the battery voltage drops below the setpoint for three minutes, a popup will appear notifying the user that the battery voltage is low. The Low Voltage Alert can be adjusted from 11.8V to 12.4V, or the alert can be turned off. The Default setting is On at 12.4V. To adjust the Low Voltage Alert, select the Battery tab in the Settings page, then move the voltage slider to the desired voltage.
NCS40T • Home Page Operation From the home page, you can check the battery voltage, operate the hydraulic lift, perform a light check on the trailer lights, operate the auxiliary function and check the TPMS sensors. • Battery Check To check the battery level, press the Battery icon on the home page. In the battery page, the voltage will be displayed and there is a bar graph to indicate the state of the battery. The graph will be green at 12.9V volts or higher. The graph will be yellow between 11.9 to 12.
NCS40T • Hydraulic To perform the Hydraulic lift function, press the Hydraulic icon from the home page. The user will be prompeted with two Travel Lock Engaged popups. To proceed, make sure it is safe to proceed, then press Yes on the first popup. The second popup will appear, press Yes again. Once in the Hydraulic page, the Travel Lock counter will start counting down from 60 seconds. Press the Up button to raise the hydraulic lift and press down to lower the hyrdaulic lift.
NCS40T • Light Check To perform the Light Check, press the Light Check icon on the home page. The user will be prompeted with two Travel Lock Engaged popups. To proceed, make sure it is safe to proceed, then press Yes on the first popup. The second popup will appear, press Yes again. Once in the Light Check page, the Travel Lock Counter will start counting down from 120 seconds. Press either the Left Turn, Right Turn, Running or Brake light bar.
NCS40T • Auxiliary To perform an Auxiliary function, press the Auxiliary icon on the home page. The user will be prompeted with two Travel Lock Engaged popups. To proceed, make sure it is safe to proceed, then press Yes on the first popup. The second popup will appear, press Yes again. Once in the Auxiliary page, the Travel Lock timer will start counting down from 60 seconds. If the latch function was selected in the Auxiliary Settings page, there will be an On/Off button to operate.
NCS40T • TPMS To access the iN-Command TPMS App, press the Tire icon on the home page. The TPMS App will then launch. Please see the iN-Command TPMS manual for operation instructions. To go back to the iN-Command Trailer App, press the iN-Command App icon at the top left corner of the TPMS App. You can also use the devices back button to return to the previous app.
NCS40T • Troubleshooting Symptom Solution • Check for a solid red light on top of the NCS40T. A solid red light indicates it is powered on. A flashing red light indicates it is in the boot up process. Not powering up • Check for +12V on the charge line in the 7-way connector. • Check for Ground in 7-way connector. • Check the Truck/Light Power Input connector to make sure it is fully seated with the mating trailer connector. • Check that the NCS40T is powered on.
NCS40T • Specificatons App Support Button LEDs Operation voltage Max curuent draw at Dimension Water resistance Working temperature Weight Certification iOS 10.0 and up, Android 6.0 and up. (1 device at a time) Bluetooth pairing button Power Status (boot status), Pairing Status 12 VDC 12 VDC / 650mA 228.3(W) x 150.8(H) x 33.0 (D) mm 8.99 (W) x 5.94 (H) x 1.30 (D) inch IP65 -20~+85 ℃ Approx. 1.06kg / 2.
NCS40T • FCC NOTES IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. No change to the antenna or the device is permitted.
www.jensenrvdirect.com ©2015 ASA Electronics LLC.
