User's Manual

INSTALLATION
INSTALLATION
Hose connection
 Gas cooker is equipped with the gas
connection on the right side with
exterior thread ISO 7-R1/2.
 Certain appliance are supplied with
the attached liquid gas coupling and
the sealing gasket.
 The connection R1/2 must be gripped
tight during the connection p rocedure
to prevent it from revolving.
 Use metal or non metal gaskets for
connection packing. Gaskets are
intended for single use only.
 The deformation of the non-metal
gasket connection thickness during
tightening may not exceed 25%.
 Connect the appliance to the gas
coupling by means of certified flexible
hose. The hose may not touch the
bottom panel of the appliance or the
rear panel and ceiling of the oven.
 Connect the appliance in accordance
with the regulations of the local gas
supplier.
Caution!
On completion of the cooker installation,
the tightness of all connections should be
checked, e.g. applying water with soap.
Do not use fire to check tightness.
Flexible hose connection
In case the appliance is connected by
means of a flexible hose the position A of
the hose is not permissible.
In case the connection hose is made of
metal, position A is permissible.
A
B
C
D
Beginning of operation
Start using the appliance in accordance
with the instructions for use.
Lit up all burners and check the stability of
the flame with high and low setting. Adjust
air intake if necessary. After that, take time
and explain the operation and control of
the appliance to the user and read with him
the instructions for use.
Liquefied gas connection
9 Pipe coupling liquefied
10 Gasket
11 Connection R 1/2
11
10
9
Adapting the cooker to
another type of gas
This operation may only be carried out by
an appropriately authorised fitter.
The cooker is supplied with natural gas
(G20/20mbar).If the cooker is to be
supplied with differs from the gas provided
for the cooker by the manufacturer, burner
nozzles must be exchanged and the flame
needs to be adjusted.
Caution!
The cookers provided by the manufacturer
have burners which are factory -adapted to
use the gas specified on their data plates
and guarantee cards.
In order to adapt the cooker to burn a
different type of gas, you should:
● exchange nozzles (see tables below),
● adjust the “economical” flame.
Burner
10
11
Gas connection
• Accessibility: Make sure that it is possible to
run gas lines
to the gas connection point of the
appliance.
The gas connection point must be
accessible without having to remove the oven.
If a flexible hose is used,
the connection point
mustalso be accessible without having to remove
the oven.
• ULPG connection: Using the supplied gas regulator, remove the dust seals on the inlet and outlet
ports and position the outlet port of the regulator towards the gas inlet pipe of the oven. Using a
suitable thread sealant, screw the regulator on and ensure that it is orientated with easy access to
the test point. Connect the appropriate ULPG supply to the inlet port of the gas regulator.
• Natural gas connection: Using the supplied gas
regulator, rem
ove the dust seals on the inlet and
outlet ports and position the “OUT” port of the
regulator towards the gas inlet pipe of the oven.
Using a suitable thread sealant, screw the regulator on and ensure that it is orientated with easy
access to the test point. Connect the appropriate Natural Gas supply to the “IN” port of the gas
regulator.
Gas regulator
test point
Outlet port to
gas oven
Gas supply
inlet port
Gas regulator
test point
Outlet port to
gas oven
Gas supply
inlet port
Upright
Burner
Gas type
Injector
TPP
NGC
Size(mm)
(kPa)
(MJ/h)
Auxiliary
Semi-rapid
Oven
Natural gas
Universal
LPG
Auxiliary
Semi-rapid
Oven
0.87
1.10x2
1.39
1.0
3.6
12.6
6.3x2
10.8
0.53
0.68x2
0.89
2.75
3.6
6.3x2
12.6
10.8
540mm
Wok
1.65
Wok
0.95