User's Manual
9 10
BLUETOOTH PAIRING AND PLAYBACK
LISTENING FROM LINE IN JACK
CARE AND MAINTENANCE
1. Power on the unit as previous procedures.
2. Press the BT (Bluetooth) button on the remote control to switch to BT mode. Blue indicator will turn
on and blink.
3. Turn on the BT function in the external BT player and wait a few seconds until the external BT
player and the speaker were paired. Play the music in the external BT Player as usual.
NOTES:
In first time use, pairing the external BT Player to the unit as below:
1. Switching the unit to BT mode as previous procedures, the blue indicator will turn on and blinking.
2. Power on the external BT player and enter to BT searching mode. Start pairing as the on screen
instructions on the external BT Player (For details pairing procedures, please refer to the user’s
manual of your BT player.).
3. When the external BT player searched the unit, our model number “ CE7001-BT ” will appear on the
display of external BT player.
4. Pairing code “0000” or "1234" may need to enter.
1. Connect the Headphone/Earphone; Line out jacks from the
external audio player (such like MP3 player; Discman … etc.) to
the LINE IN jacks on the unit by the supplied “Line In connection
cable” as the figure on right.
2. Power on the unit as previous procedures. Press STANDBY/
SOURCE button to turn it to Line In mode. The STATUS
indicator would light up in PURPLE.
Note: If the unit is in BT (Bluetooth) mode, the status indicator
will light in blue. Press the LINE button on the Remote Control to
switch to Line In mode.
3. Power on the connected external player and start playback as
usual.
4. Press the volume buttons to adjust volume level.
5. Press the MUTE button to turn off the sound, press again to
resume.
6. When finished listening, press and hold STANDBY button for 3
seconds on the unit or press STANDBY button on the remote
control to power off (Standby Mode) the unit. (The status
indicator will light in red.)
NOTE:
To saving electric power, unplug the AC/DC Power Adaptor from
wall outlet if long period of time will not use the unit.
1. Place the unit on a level surface away from sources of direct sunlight, excessive heat caused by
heating equipment, humidity, rain or sand.
2. Protect your furniture when placing your unit on a natural wood and lacquered finish. A cloth or other
protective material should be placed between it and the furniture.
3. Do not clean your unit by water directly. Clean the unit with a soft, clean cloth slightly moistened with
plain lukewarm water only.
4. Stronger cleaning agents, such as Benzene, thinner or similar materials can damage the surface of
the unit.
5. Do not attempt to disassemble your product.
6. Do not paint your product with lacquer or aerosol.
7. Do not drop, throw or try to bend your product.
8. Do not expose your product to open flames.
TROUBLESHOOTING
Check the connection of the
AC/DC adaptor between the unit
and wall outlet.
Volume control is set at minimum
or mute.
Check that the volume control is
NOT at minimum.
Check that it is not set to mute.
The volume control of external BT
player (or audio player) is too low.
No sound
No power when
POWER is on
Increase the volume of external
BT player (or audio player).
PROBLEM
POSSIBLE CAUSE
SOLUTION
The remote control
does not work
Obstacles obscure the front of the
unit.
Make sure there is no bostacles
obscuring the front of the unit.
No sound in
Bluetooth (BT) mode
The pairing had not ben done
properly.
Check if you have pairing or not.
It needs to pair the external BT
player and the speaker with
password “0000” or “1234” before
1st time listening.
AC/DC adaptor is not plugged into
a wall outlet or the connector is not
plugged into the power supply or
the DC IN jack of the unit.