Installation Guide

ManualsBrandsArtmore Tile ManualsFlooringRogue Birch Moon 6-in x 48-in Waterproof Interlocking Luxury Vinyl Plank Flooring (27.39-sq ft)

1 of 7

art

RIGID CORE-CLICK LVT INSTALLATION INSTRUCTIONS

GENERAL INFORMATION

These instructions cover all rigid core-click installations of ArtMore Luxury Vinyl Plank and Tile (LVF). All recommendations are

based on the most recent available information. The information on these sheets provides general guidelines. For complete

details please visit our website. These instructions and recommendations must be followed for a satisfactory installation.

The installation of ArtMore LVF is straightforward and similar to the installation procedures that apply to all quality resilient flooring.

Proper preparation is essential for trouble-free installation. Do not install ArtMore LVF until job-site testing and subfloor preparations

are finished and the work of all other trades is completed. Site conditions must comply with the relevant building codes and local,

state and national regulations.

• ArtMore Luxury Vinyl Flooring is recommended for use over properly prepared concrete, suspended wood, metal and other suitable

substrates. Never install ArtMore LVT over residual asphalt type (Cutback) adhesive as “Bleed Through″ may occur.

• ArtMore LVF is not suitable for external installation or unheated locations.

TOOLS AND MATERIALS OPTIONAL TOOLS AND MATERIALS

ArtMore LVT Rigid Core Flooring Router

Pull Bar Drill

Spacers Table Saw

Transitions + Molding Pieces Miter Saw

Carpenter’s Square Circular Saw

Tape Measure Hand Saw

Polyethylene Tape Jigsaw

Hammer Undercut Saw

Utility Knife Dividers

Safety Glasses Chalk Line

Dust Mask

Saw (see optional tools)

100% Silicone Caulk (for bathroom + high moisture installations)

MATERIAL RECEIVING, HANDLING + STORAGE

1. All floor covering products require care during storage and handling. It is important to store flooring products in a dry, temperature-

controlled interior area.

2. Most ArtMore LVT rigid core floors do not require acclimation, depending on storage conditions, it is advised that the product being

installed be within the same temperature range of the room during service conditions.

3. The room temperature range should be between 55° F (13° C) and 95° F (35° C) with a relative humidity maintained between 35% and

70% before, during and post installation.

4. If the above conditions cannot be met, an 8 hour acclimation period is required.

Summary of content (7 pages)

PAGE 1
art MORE RIGID CORE-CLICK LVT INSTALLATION INSTRUCTIONS GENERAL INFORMATION These instructions cover all rigid core-click installations of ArtMore Luxury Vinyl Plank and Tile (LVF). All recommendations are based on the most recent available information. The information on these sheets provides general guidelines. For complete detail s please visit our website. These instructions and recommendations must be followed for a satisfactor y install ation.
PAGE 2
5. Flooring materials that are shipped in cartons must also be stored properly. Cartons must be kept squarely positioned on the pallet to prevent distortion of the contents and to be fully supported. 6. Do not store close to exterior walls, in direct sunlight or near HVAC vents. 7. Stored cartons are to be protected from forklift and other traffic that can damage carton corners. 8. Never double-stack pallets of flooring products. 9.
PAGE 3
ASBESTOS WARNING! DO NOT MECHANICALLY CHIP OR PULVERIZE EXISTING RESILIENT FLOORING , BACKING , LINING FELT, ASPHALTIC “CUTBACK″ ADHESIVES OR OTHER ADHESIVES. Previously installed resilient floor covering products and the asphaltic or cutback adhesives used to install them may contain either asbestos fibers and/or crystalline silica. Avoid creating dust. Inhalation of asbestos or crystalline dust is a cancer and respiratory tract hazard.
PAGE 4
the intended usage. Install and prepare panels and seams according to the manufacturer’s instructions. Also refer to ASTM F1482, “Standard Practice for Installation and Preparation of Panel Underlayments to Receive Resilient Flooring.″ • Many times, wood panel subfloors are damaged during the construction process or are not underlayment grade. These panels must be covered with an appropriate underlayment.
PAGE 5
PREPARATION • ArtMore LVT rigid core floors are floating floors and should not be adhered or nailed to the substrate. • ArtMore LVT rigid core floors are intended for indoor use only. • A minimum 1/4” (6.3mm) expansion space is required around all walls and vertical objects. Allow a 1/2” (12.7mm) space for installations over wood substrates that may be effected by moisture or external temperature and humidity fluctuations (i.e.
PAGE 6
x. If this distance is less than 8˝ (20.32 cm) go back to the first full plank and cut approximately 8˝ (20.32 cm) from the end closest to the starting wall. This will leave a longer piece at the end of the first row. xi. To cut the last piece, use a sharp utility knife and a straight edge, score a line on the top surface of the plank/tile. The plank/tile should split on the score line with little effort, use a saw to cut to size. **Note: The end pieces need to be longer than 8 inches (20cm).
PAGE 7
fluctuations or when installing in areas without permanent HVAC controls. Do not fasten moldings through the flooring. Fasten into the wall. • Use plywood to cover the top of the flooring when moving heavy furniture or appliances into position. • Use proper floor protectors under the legs of furniture. REPAIRS • If a damaged piece needs to be replaced and is close to a parallel wall: ο Remove the molding from the walls nearest the damaged piece. ο Remove the planks/tiles by unlocking them.