INSTA ALLA ATION N GU UIDE RC CC640 0-R Retro ofit Su ubwoo ofer M Module e RC CC640 0-PC Pre-C Constructio on Sub bwooffer Mo odule
CARTON CONTENTS: RCC640-PC: 1. RCC640 Pre Construction Subwoofer 1. Grille 1. Paint / Debris Shield [Installed] 8. Paint / Debris Shield Mounting Screws [Installed] 4. L-Shaped Mounting Brackets 16. Mounting Bracket Screws 32. 1/8” [3 mm] Grille Spacers 16. Long Grille Spacer Mounting Screws 1. Installation Guide RCC640-R: 1. 1. 1. 1.
Thank you for choosing Artison’s RCC640 Subwoofers. We are pleased that you have selected our high-performance audio products. INTRODUCTION The following information will guide you through the installation and setup of your Artison RCC640 Retrofit Subwoofer or RCC640 Pre-Construction Subwoofer. The RCC320 and RCC640 model series are in wall subwoofers featuring second generation of Artison’s Reactance Cancelling Configuration which allows vibration free operation.
RCC640 RETROFIT SUBWOOFER [RCC640-R] The RCC640-R was designed be installed into a 2 x 4 stud wall with a minimum of 16” on center spacing. The retrofit subwoofer is not impacted by cabinet orientation but needs to be used vertically to fit into standard 16” on center stud spacing. The classical rule for subwoofer placement is that the subwoofer should be placed on the same wall the front channels are located, positioned at one-third of the total distance of the wall.
3. Paint the Grille / Trim Ring with a spray method or a low nap roller. Be sure to not clog the perforations in the grille mesh. Use compressed air to blow excess paint out before it dries. 4. DO NOT get paint on the speaker baffle or speaker cones. Paint can damage these components which would VOID your Warranty.
need to be replaced over the cabinet. Bracing would be required on the top and bottom of the rough opening to reattach new wallboard. Uncovering the adjacent stud faces is also helpful to provide a large surface area to reattach drywall. Using fiberglass tape and joint compound join the new section with the surrounding wallboard and sand once dry. 3. Using 2 conductor speaker wire, run between the subwoofer amplifier and the subwoofer.
the cabinet wall must at least be 12.5 mm [0.5”] if the grille is going to be used. 4. When venting the output of the subwoofer through a built-in cabinet’s baseboard, please reference the points below: a. Please allow for a minimum of 640 cm2 [100 in2] of total open area in the baseboard. If less open area is provided the subwoofer will be restricted and may cause noise through the vent. b. Rounded corners will minimize air noise. c.
SPECIFICATIONS & DIMENSIONS: RCC 640 Retrofit Subwoofer RCC640-R Cut Out Dimensions: H 25.4” [645 mm] x W 14.3” [363 mm] Mounting Depth: 3.8” [97.5 mm] Grille: H 26.9” [683 mm] x W 16.0” [405 mm] x D 0.16” [4 mm] Driver Complement: 8 ea.
RCC 640 Pre-Construction Subwoofer RCC640-PC Cabinet: H 28.6” [727 mm] x W 14.0” [354 mm] x D 3.5” [89 mm] Grille: H 29.3” [745 mm] x W 3.7” [95 mm] x D 0.16” [4 mm] Grille Cut Out: H 28.6” [727 mm] x W 3.0” [78 mm] Driver Complement: 8 ea.
LIMITED WARRANTY This warranty remains in effect for five years from the date of purchase for speaker products and one year for electronic products. THIS WARRANTY PROTECTS THE ORIGINAL OWNER PROVIDING THAT THE PRODUCT HAS BEEN PURCHASED FROM AN AUTHORIZED ARTISON DEALER IN THE UNITED STATES. THE ORIGINAL BILL OF SALE MUST BE PRESENTED WHENEVER WARRANTY SERVICE IS REQUIRED.
