INSTALLATION GUIDE Masterpiece LCR DualMono® Portrait LCR DualMono® Sketch LCR DualMono® M-LCR-DM P-LCR-DM S-LCR-DM
CARTON CONTENTS: • • • • • • 2. 2. 2. 4. 4. 1. • • • • 8. 2. 1. 1. LCR OM Speakers Thin Universal Mounting Brackets LCR OM Brackets LCR OM Thumbscrews LCR OM Extension Plates Hardware Accessory Kit o 1. 2 meter, 16 gao OualMono Jumper Speaker Wire o 1. 3mm Allen Wrench o 16. Bracket to Bracket (B to B) Screws, #10-32 x 7 mm o 4. Machine Screw, M4 x (13, 18 & 25) mm o 4. Machine Screw, M5 x (13, 18 & 25) mm o 4. Machine Screw, M6 x (13,18 & 25) mm o 4. Machine Screw, M8 x (13, 18 & 25) mm o 4.
Thank you for choosing the Artison LCR DualMono® Speakers. We are pleased that you have selected our high-performance audio products. The following information will guide you through the installation of your Artison LCR DualMono Speakers. INTRODUCTION Artison LCR OualMono (LCR OM) speakers are designed to attach directly to any Flat Panel TV (FPTV) with the included Thin Universal Mounting Bracket (Thin UMB) and come with custom made grilles specific to your FPTV.
INSTALLATION OPTIONS The Artison LCR OM Speakers were designed to have multiple installation options using the included hardware and brackets. • Attachment to any Flat Panel TV (FPTV) in a Tablestand or Wall Mounted installation. • On-Wall/Surface Mounting. Please read the instructions below before attempting your installation. INSTALLATION PROCEDURES The Thin UMB was designed in compliance with the VESA Mounting Standards.
SLIDER ARM POSITION BASED ON FPTV THICKNESS 8. Depending on the FPTV depth the Slider Arm Position and use of LCR Extension Plates will vary. Refer to the following; TABLE 1 and FIGURES 1-6, to see how best to setup your Thin UMB. 9. If TABLE 1 calls for the 'Backward' position. Remove the Slider Arm from the Aluminum Main Bar, rotate 180 degrees, and reinsert into the Aluminum Main Bar. Figure FPTV Thickness 1 2 3 4 5 6 0.28" -1.0" 1.0" - 1.75" 1.5" - 2.25" 2.0" - 2.75" 2.9" - 3.75" 3.4" - 4.
7mm [0.28"] 39.3mm [1.54"] FIGURE 1 25.4mm [1.00"] 20.9mm [0.82"] FIGURE 2 38.1mm [1 .50"] 8.2mm [0.
50.8mm ~ [2.00"] FIGURE 4 73.7mm [2.90"] ~--------------~-------~~~~===~=====~~~~ _ ~U ~-------------~-----~~~==-=-==~=~~7 v ~ =_=__ -~--c.r-- FIGURE 5 86.4mm [3.
FOAM DAMPENERS 12. The foam provides both damping for the mounting system and stabilizes the speaker. The pads should be attached to the television surface behind the Slider Arm. The foam is intended to be highly compressed to fit under the Slider Arm. 13. Expose the adhesive backing by folding a small corner of the protective paper back on itself. Then unfold the paper and remove. 14. Place the 2" x 2" x 1" Foam Dampeners to the TV chassis directly underneath the Slider Arms close to the speaker.
HARDWARE KIT 15. Mounting Screw Selection 15.1. Thread Pitch: M4, M5, M6, M8, or M10. 15.1.1. Match the threads in the FPTV chassis to one from the kit. 15.2. Screw Length: 13, 18 or 25 mm. 15.2.1. First, check the thread depth of the mounting points on the FPTV. 15.2.2. Select a length that will accommodate the Thin UMB (Depth =7mm), third party wall-mount, and washers. Allow for 5 - 8 mm of screw threads into the FPTV chassis. Be sure to account for the maximum thread depth into the TV.
THIN UMB COLLAR WASHER FLAT WASHER MOUNTING SCREW FIGURE 9 THIN UMB COLLAR WASHER WALL MOUNT BRACKET FLAT WASHER MOUNTING SCREW FIGURE 10 10
MOUNTING THE LCR OM BRACKET TO THE THIN UMB 20. Remove the LCR OM Bracket from the speakers by loosening the 2 thumbscrews in a counter-clockwise direction. Refer to FIGURE 11. 21. Carefully slip off the bracket. NOTE: DO NOT place the LCR OM face down as this may permanently damage the drivers. 22. Attach the LCR OM Brackets to the Slider Arms using the 3 mm Allen Head Bracket to Bracket (B/B) Screws. Refer to TABLE 1 for the correct screw location. 23.
x FIGURE 12 12
MOUNTING THE LCR OM SPEAKER INTO LCR OM BRACKET 25. Carefully slide the LCR OMs into the vertical bracket that is now mounted to the display. Place each speaker on their corresponding sides of the television. The OualMono Center Channels should be located on the top half ofthe display. Refer to Figure 13. 26. Using the thumbscrews loosely re-attach the speakers. Adjust the front to back speaker position using the slot until the front edge is approximately 1/4" behind the front surface of the bezel. 27.
GRILLE INSTALLATION 28. Grilles are held to the speaker by Hook and Loop fasteners, commonly known as Velcro®. All LCR OM Grilles have 2 large hook pads. The woofer motors have the Loop surface. 29. Align the grille with the top and bottom edges of the FPTV, directly over the face of the speaker baffle. 30. Press the grille firmly onto the woofer motor surfaces. 31. The grille can be removed easily by simply pulling on the grille to separate the Velcro pads. 32.
ON-WALL INSTALLATION OF THE LCR OM 1. Remove the LCR OM Bracket from the speakers by loosening the 2 thumbscrews in a counter-clockwise direction. 2. Carefully slip off the bracket. Refer to FIGURE 11. NOTE: DO NOT place the LCR face down as this may permanently damage the drivers. 3. The LCR OM Brackets have two slots cut through the rear of the part which will function as a surface mount bracket. Refer to FIGURE 14. 4.
WIRING THE LCRS 3 CHANNEL METHOD (Left, DualMono Center and Right) 1. Operate the terminals by firmly pressing on them. An opening will be exposed in the side of the terminal. Slip about 9 mm (3/8") of bare speaker wire into this opening hole and release the terminal. The spring loaded terminal will now securely hold the wire in place. 16 gauge is the minimum requirement. Depending upon total wire length a larger gauge may be used. 12 gauge is the maximum that will fit into the terminals. 2.
Top Rear ."" Right Center / I~~ Stage Tweeter r'l ~~I -- ~ 3 CHANNEL METHOD I~~ Right Channel Left Center !)lII@§) / 11:: - + "- Right . o () o Amplifier - O..e .:t.. ~ ~ Stage Tweeter I ...... "" Center ~ Left Left Channel ~ FIGURE 15 ""-I Right Center / Top Rear I~@~ y Stage Tweeter ~ ¥! Left Center I e=@~ I y ~ 2 CHANNEL METHOD ~ I ,- •• .2 ~l· ..1- I " ~ ::::::. -.
FINE TUNING YOUR LCR-DM SPEAKERS Satellite / Subwoofer Crossover Frequencies: P-LCR-DM & S-LCR-DM: • 'SMALL' Speaker on AN Receiver / Processor • Crossover Frequency: 85 Hz • Crossover Slope: 12 dB/octave M-LCR-DM: • 'SMALL' Speaker on AN Receiver / Processor • Crossover Frequency: 80 Hz • Crossover Slope: 12 dB/Octave Stage Tweeter ON / OFF Switch: This located on the front baffle of each speaker below the Left/Right Channel Woofer. • In most applications, the Stage Tweeter should be ON.
SPECIFICATIONS & DIMENSIONS: Masterpiece LCR DualMono M-LCR-DM Dimensions: 29.6" x 6.3" x 2.4", HWD Overall 30.0" x 6.5" x 2.6", HWD wI Minimum Grille Mounting Depth 2.1" :5 (TV + Thin UMB + Wall Mount) For use with FPTV's 55" or larger: H ~ 30.0", D 0.28" - 4.4" Driver Complement: 2. 5%" Kevlar, Long Throw, Inverted Magnet, MidrangelWoofer 2. 8 x 1" ART Drivers in Curved Line Array 1.
158.3mm [6.2"] 344.8mm [13.6"J 50mm [2.0"] \ 777.6mm [30.6'1 330mm [13.0"] 50mm [2.0"J . 62mm [2.4"] ;\ 751.6mm [29.6"] ~ i .' 344.8mm [13.6"] 4mm [0.2"j- -- 45.7mm [1.8"] 62.3mm [2.4"] 66.5mm [2.6") I 53.8mm [2.1"] 165.1mm [6.5"] - 50mm [2.0") 777.6mm [30.6"J 787.4mm [31.0"J 330mm [13.0"] 50mm [2.0"] 4mm [0.2"] - - NOTE: MINIMUM GRILLE HEIGHT 762mm [30.
Portrait LCR DualMono P-LCR-DM Dimensions: 25.0" x 6.3" x 2.4", HWD Overall 25.4" x 6.5" x 2.6", HWD w/ Minimum Grille Mounting Depth 2.1" ::; (TV + Thin UMB + Wall Mount) For use with FPTV's 46" or larger: H ~ 25.4", D 0.28" - 4.4" Driver Complement: 2. 4%" Kevlar , Long Throw, Inverted Magnet, Midrange/Woofers 2. XT25 Super Audio Tweeters, 15° Swivel Mount 1.
1S8.3mm ;- (6.2") _ SOmm [2.0"] 661mm [2~.0"] 286.5mm [11.3") SOmm [2.0'1 , 286.Smm [11.3'1 1 , 4mm [0.2"] 63Smm [25.0") 62mm [2.4") 330mm [13.0"] I ,i I , - I 4S.7mm [1.8"] 62.3mm [2.4"] 66.5mm [2.6"] 53.8mm [2.1"] 16S.1mm [6.S"} SOmm [2.0"] 661mm [26.0"} 330mm [13.0"] t • :J, 673.1mm [26.5") I 50mm [2.0"] I , 4mm [O.2"J NOTE: MINIMUM GRILLE HEIGHT 645.2mm [25.
Sketch LCR DualMono S-LCR-DM Dimensions: 25.0" x 6.3" x 2.4", HWD Overall 25.4" x 6.5" x 2.6", HWD wi Minimum Grille Mounting Depth 2.1" =:; (TV + Thin UMB + Wall Mount) For use with FPTV's 46" or larger: H ~ 25.4", D 0.28" - 4.4" Driver Complement: 2. 4~" Polypropylene, Long Throw, Inverted Magnet, Midrange I Wooters 2. 27mm Super Audio Tweeters 1.
158.3mm [6.2"] !$ ..... 286.5mm [11.3"] 50mm [2.0"] I I 635mm [25.0"] 661mm [26.0"] 330mm [13.0"] 62mm [2.4"] 286.5mm [11.3'1] 50mm [2.0"] I I 4mm ./ [0.2"J 45.7mm [1.8 1' ] 62.3mm [2.4"] 66.5mm [2.6"] :r . ' < 53.8mm [2.1"] 165.1mm [65"J 50mm [2.0"] 661mm [26.0"] 330mm [13.0"] , .. \ 673.1mm [26.5'1 50mm [2.0"] 4mm [0.2"] NOTE: MINIMUM GRILLE HEIGHT 645.2mm [25.
LCR OM GRILLE Cloth Colors: Black and Light Grey Dimensions: (FPTV Height) x 6.5" x 1.0", HWD Minimum Height 25.4" for Sketch LCR-DM Minimum Height 25.4" for Portrait LCR-DM Minimum Height 30.0" for Masterpiece LCR-DM THIN UMB Dimensions: 2.5" x 40.5" x 0.28", HWD wi Arms Retracted 2.5" x 68.5" x 0.
REPACK DIAGRAM 28
LIMITED WARRANTY This warranty remains in effect for five years from the date of purchase for speaker products and one year for electronic products. THIS WARRANTY PROTECTS THE ORIGINAL OWNER PROVIDING THAT THE PRODUCT HAS BEEN PURCHASED FROM AN AUTHORIZED ARTISON DEALER IN THE UNITED STATES. THE ORIGINAL BILL OF SALE MUST BE PRESENTED WHENEVER WARRANTY SERVICE IS REQUIRED.
Place Stamp Here ARTISON Attention: Customer Service Department 774 Mays Blvd.
Name Address Company Telephone Number Email Date/Price Name of Dealer Address of Dealer Product(s) Model Numbers Please rate your overall experience with the dealer.
