MSDS

ManualsBrandsArtisan ManualsPaint1-gal. Safer Mold and Mildew Stain Remover for Masonry

MATERIAL SAFETY DATA SHEET

Artisan Safer Mold & Mildew Stain Remover

Page 1 of 6

SECTION 1 PRODUCT NAME AND COMPANY IDENTIFICATION

Product Name: Artisan Safer Mold & Mildew Stain Remover

Manufacturer:

Chemique, Inc.

315 N. Washington Avenue

Moorestown, NJ 08057

(856) 235-4161

MSDS Date of Preparation: 11/13/10

EMERGENCY PHONE: 800-535-5053 (Infotrac)

SECTION 2 COMPOSITION/INFORMATION ON INGREDIENTS

INGREDIENTS

CAS#.

WT.%

Ammonium Pentaborate

12046-04-7

11.5

Surfactant

Proprietary

Water

7732-18-5

83.5

SECTION 3: HAZARDS IDENTIFICATION

This product is a pale amber liquid.

EMERGENCY OVERVIEW

CAUTION! May cause eye irritation. Prolonged or repeated contact with the skin may cause

irritation, defatting, drying and dermatitis. Ingestion may cause gastrointestinal irritation.

HEALTH HAZARDS:

INHALATION: Inhalation of mists may cause mild irritation to nose and throat.

SKIN CONTACT: Prolonged or repeated contact may cause skin irritation, drying, defatting, and

dermatitis.

EYE CONTACT: May cause moderate eye irritation with stinging and watering of eyes.

INGESTION: May cause gastrointestinal irritation with nausea, vomiting, diarrhea, and cramps.

CHRONIC EFFECTS OF OVEREXPOSURE: Repeated skin contact may cause dermatitis.

MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE: Individuals with skin diseases may be at

increased risk from exposure to this material.

Summary of content (5 pages)

PAGE 1
MATERIAL SAFETY DATA SHEET Artisan Safer Mold & Mildew Stain Remover SECTION 1 PRODUCT NAME AND COMPANY IDENTIFICATION Product Name: Artisan Safer Mold & Mildew Stain Remover Manufacturer: Chemique, Inc. 315 N. Washington Avenue Moorestown, NJ 08057 (856) 235-4161 MSDS Date of Preparation: 11/13/10 EMERGENCY PHONE: 800-535-5053 (Infotrac) SECTION 2 COMPOSITION/INFORMATION ON INGREDIENTS INGREDIENTS Ammonium Pentaborate Surfactant Water CAS#. 12046-04-7 Proprietary 7732-18-5 WT.% 11.5 5 83.
PAGE 2
MATERIAL SAFETY DATA SHEET Artisan Safer Mold & Mildew Stain Remover SECTION 4 FIRST AID MEASURERS EYE CONTACT: Immediately flush eyes with water for at least 15 minutes while lifting the upper and lower lids. Get medical attention if irritation persists. SKIN CONTACT: Immediately wash area thoroughly with soap and water. Remove contaminated clothing and launder before reuse. Get medical attention if irritation persists. INHALATION: Remove to fresh air.
PAGE 3
MATERIAL SAFETY DATA SHEET Artisan Safer Mold & Mildew Stain Remover SECTION 8 EXPOSURE CONTROLS/PERSONAL PROTECTION Exposure Guidelines: INGREDIENTS Ammonium Pentaborate Surfactant Non-hazardous Ingredients CAS#. 12046-04-7 Proprietary NA EXPOSURE LIMITS None Established None Established None Established RESPIRATORY PROTECTION: Good general ventilation (equivalent to outdoors) should be adequate under normal conditions.
PAGE 4
MATERIAL SAFETY DATA SHEET Artisan Safer Mold & Mildew Stain Remover SECTION 11 TOXICOLOGICAL INFORMATION TOXICOLOGY DATA: This product has not been tested as a whole. Toxicity values for the components are: Ammonium Pentaborate: Oral rat LD50: 4200 mg/kg Surfactant: No toxicity data is available None of the components of this product is listed as a carcinogen or suspected carcinogen by IARC, NTP or OSHA. None of the components are known to cause sensitization in animals or humans.
PAGE 5
MATERIAL SAFETY DATA SHEET Artisan Safer Mold & Mildew Stain Remover EPA SARA 313: This product contains the following chemicals regulated under SARA Title III, section 313: None CERCLA Hazardous Substances (Section 103)/RQ: This product is not subject to reporting under CERLCA. Many states have more stringent release reporting requirements. Report spills required under federal, state and local regulations. TOXIC SUBSTANCES CONTROL ACT: All of the components of this product are listed on the TSCA inventory.