Light Tower Assembly Instructions is a registered trademark of Artec Co., Ltd. in multiple countries including Japan, South Korea, Canada, and the USA.
Light Tower Contents Studuino Unit Battery Box ×1 LED (red) LED (green) Red Buzzer ×1 ×4 Blue Light Sensor Basic Cube (clear) White ×1 Sound sensor Sound Sensor ×1 ×8 Half D (light blue) LED (white) ×1 Light sensor Basic Cube (white) LED (blue) Green ×1 Buzzer ×1 ×1 Touch sensor ×1 Half B (blue) ×1 Half C (light aqua) ×3 ×4 Touch Sensor ×29 Sensor Connecting Cable (three-wire 15 cm) USB Cable ×1 ×8 02
Biped Walking Robot Assembly Instruction Labels ×1 Shows the parts needed for assembly. Indicates the number of parts needed for assembly. Indicates tips or warning when building a specific item. Shows an image of the completely assembled item. Indicates when the direction of a component must be changed for assembly.
Light Tower Adding the Battery Box ×1 ×1 Connect the cable from the battery box to the POWER section.
Light Tower Assembling the Base ×12 ×3 ×1 ×1 ×2 ① Sensor Connecting Cable Sensor side Sound Sensor 1. Circuit board side 2.
Light Tower ② 1. 2.
Light Tower ④ ×2 ⑤ 07
Light Tower ⑥ 08
Light Tower Assembling the Touch Sensor ×3 ×1 ×1 ×1 Touch Sensor Gray Black Make sure the cables are inserted correctly! 09
Light Tower Assembling the Center ×8 ×3 ×3 ×2 ×1 ×1 ×1 ×1 ×4 ① 1. Green Gray Black Make sure the cables are inserted correctly! 2.
Light Tower ② Red Gray Black Make sure the cables are inserted correctly! White Gray Black Make sure the cables are inserted correctly! 11
Light Tower ③ Make sure the cables are inserted correctly! Buzzer Gray Black 12
Light Tower ④ Red White Buzzer 13
Light Tower Assembling the Top ×6 ×1 ×2 ×3 ×1 ×1 ×1 ① Blue Gray Black Make sure the cables are inserted correctly! Make sure the LED is inserted correctly! 14
Light Tower ② 15
Light Tower Putting the Parts Together ① Connect the cable from the touch sensor to A4 .
Light Tower ③ Connect the cable from the blue LED to A2 and the cable from the white LED to A3. Blue White A3 A2 Make sure the cables are inserted correctly! ④ Connect the cable from the green LED to A1 and the cable from the red LED to A0.
Light Tower ⑤ Connect the cable from the buzzer to A5, the cable from the light sensor to A6, and the cable from the sound sensor to A7.
Light Tower ③ Reverse 19
Light Tower Replacing the Batteries ① ② ③ ④ ⑤ Use a screwdriver (Phillips #1) to open. Insert batteries in the correct polarity. Put the lid of the battery box back in place.
Light Tower Completed Light Tower ● Before operating your robot, check the Assembly Instructions again to confirm your robot has been assembled correctly.
Light Tower Operating Your Light Tower Install the software from the URL below to setup the Studuino Programming Environment. ★ Proceed to Step 1 when software installation is complete. http://www.artec-kk.co.jp/studuino/ ① ② Connect the USB cable to the PC and the Studuino unit. Refer to 1.3. About Studuino in the Studuino Programming Environment Manual for more details. Download the program file LightTower.ipd from the URL below in the ArtecRobo section. http://www.artec-kk.co.
Light Tower Operating Your Light Tower ① ② The LEDs will shine for five seconds in response to sound. They will also shine if your room becomes dark. Making contact with the touch sensor will make the LEDs shine and the buzzer will play a sound.
Light Tower Sensor Calibration Some sensors may not function properly after you run the program for the first time. If the sensors are malfunctioning, calibrate the sensor settings. Click the Submenu 1 tab to calibrate the sensors and you will see a box to adjust the range settings. Drag the mouse left or right to adjust the range settings. Refer to the Sensor Condition Icon sections in 4.4. The Attribute Field of the Studuino Programming Environment Manual for more details.
