Arm Robot Car Assembly Instructions is a registered trademark of Artec Co., Ltd. in multiple countries including Japan, South Korea, Canada, and the USA.
Arm Robot Car Components Studuino Unit Servomotor ×3 ×1 DC Motor Battery Box ×1 Touch Sensor LED (green) Touch Sensor ×1 Half B (blue) Green ×10 Triangle A (clear) ×2 ×1 Basic Cube (white) Half D (aqua) ×2 ×1 Half A (light gray) ×2 Triangle A (gray) ×11 Wheel Hub ×1 ×3 ×25 Sensor Connecting Cable (three-wire 15 cm) USB Cable Accelerometer ×2 ×1 Half C (light aqua) Accelerometer ×2 O-ring ×2 Sensor Connecting Cable (three-wire 30 cm) ×1 ×2 Sensor Connecting Cable (four-wire 5
Arm Robot Car Assembly 組立説明書のアイコンについて Instruction Labels ×1 Shows the sticker number used for each servomotor. Use the motor with the correct sticker number. Shows the parts needed for assembly. Indicates the number of parts needed for assembly. Arm Robot Car Assembling the Arms ×2 ×3 ×4 Indicates when the direction of a component must be changed for assembly. ×10 ×2 ×2 ① Shows an image of the completely assembled item. Wider 14 Indicates tips or warnings when building a specific item.
Arm Robot Car Handling the Servomotor 1 Orientation The photo to the right shows the servomotor facing you. There are two shafts, Wider (drive shaft) Narrower (movable shaft) the one with the wider space is the drive shaft and the one with the narrower space is the movable shaft. ★ When turning the drive shaft by hand, do so very slowly and gently. Excessive pressure when turning may cause damage to the servomotor. 2 Calibration and Setting Connector Numbers Before building your robot, read 6.
Arm Robot Car Preparation ×1 ×1 ×1 ×1 (three-wire 15 cm) Sensor Connecting Cable ×1 (three-wire 30 cm) Sensor Connecting Cable ×1 (four-wire 50 cm) Sensor Connecting Cable Connect the sensor connecting cable to each sensor.
Arm Robot Car Body Assembly (bottom) ×1 ×4 ① Make sure the Studuino unit is in the correct orientation! ② 06
Arm Robot Car Assembling the Motor ×2 ×2 ×2 ×2 M1 M2 ① Connect the assembled DC Motor to M1. Make sure the Studuino unit is in the correct orientation! M1 M1 Make sure the cables are inserted correctly! Slip the O-ring onto the grooves of the wheel.
Arm Robot Car ② Connect the assembled DC motor to M2. M2 Make sure the cables are inserted correctly! M2 Slip the O-ring onto the grooves of the wheel.
Arm Robot Car Body Assembly (top) ×1 ×1 ×2 ×1 ×6 ×2 ×3 ① ② 09
Arm Robot Car ③ ④ You should see the battery box switch here. the cables from the battery box ⑤ Connect to the POWER section.
Arm Robot Car ⑥ Green 11
Arm Robot Car ⑦ Connect the cable from the LED (green) to A1.
Arm Robot Car Assembling the Servomotor ×3 ×3 ×6 ×6 Wider Narrower Make three in total.
Arm Robot Car Assembling the Arms ×2 ×3 ×4 ×10 ×2 ×2 ① Wider 14
Arm Robot Car ② ③ Bottom 15
Arm Robot Car ④ the cables from servomotor ⑤ Connect on your Studuino unit.
Arm Robot Car ⑥ Wider ⑦ Connect the cables from servomotor on your Studuino unit. to their corresponding place Make sure the cables are inserted correctly! ⑧ Turn the outlined piece down.
Arm Robot Car ⑨ Turn and insert servomotor block sideways. Wider the cables from servomotor ⑩ Connect on your Studuino unit.
Arm Robot Car ⑪ 1. 2.
Arm Robot Car Assembling the Controller ×1 ×3 ×1 ×1 ① Touch Sensor Accelerometer 20
Arm Robot Car ② Connect the cable from the touch sensor to A0 and the cable from the accelerometer to A4/A5. A0 A4 A5 Connect to the accelerometer to both A4 and A5.
Arm Robot Car Replacing the Batteries ① ② ③ ④ ⑤ Use a screwdriver (Phillips #1) to open. Insert batteries in the correct polarity. Put the lid of the battery box back in place.
Arm Robot Car Completed Arm Robot Car Be cautious of cables that could become entangled in the moving parts of the motor and cause the robot to disconnect. Take care when arranging cables. Before operating your robot, check the Assembly Instructions again to confirm your robot has been assembled correctly.
Arm Robot Car Completed Arm Robot Car Top Bottom 24
Arm Robot Car Operating Your Arm Robot Car Install the software from the URL below to setup the Studuino Programming Environment. ★ Proceed to Step 1 when software installation is complete. http://www.artec-kk.co.jp/studuino/ ① ② Connect the USB cable to the PC and the Studuino unit. Refer to 1.3. About Studuino in Studuino Programming Environment Manual for more details. Download the program file ArmRobotCar.ipd from the URL below in the ArtecRobo section. http://www.artec-kk.co.
Arm Robot Car ⑥ Turn the switch of the battery box on. Immediately turn the switch to off if your robot does not begin moving as shown in the picture below. Not doing so may damage the servomotor. If your robot does not move, the servomotor may be in the wrong position or the blocks may be improperly connected. Re-read the Assembly Instructions to make sure that your robot has been assembled correctly. ⑦ ⑧ Hold the controller parallel to the ground and tilt it to make your Arm Robot Car move.
