IPS-2101h User Manual V1.0 www.artdio.com.tw ArtDio Company, Inc.
IPS-2101h User Manual Safety Instructions • Do not attempt to service the product yourself. referred to qualified service personal. • To avoid electric shock, do not put your finger, pin, wire, or any other metal objects into vents and gaps. • To avoid accidental fire or electric shock, do not twist power cord or place it under heavy objects. • The product should be connected to a power supply of the type described in the operating instructions or as marked on the product.
IPS-2101h User Manual Table of Content Table of Content........................................................................................................................3 1. Product Specifications......................................................................................................5 2. Package Content ...............................................................................................................6 3. Installation.....................................................
IPS-2101h User Manual 7.3 Others .......................................................................................................................................................21 8. Registration Message .....................................................................................................21 9. Using IPS-2101h ..............................................................................................................21 9.1 Pickup the Phone......................................
IPS-2101h User Manual 1. Product Specifications Voice Interface Call control protocol SIP (RFC-3261) or H.323 V4 or MGCP Voice compression G.711 A/µ -Law, G.723.1, G.729A/B/AB Echo cancellation G.165/G.167 16ms Delayed (End to End) < 100ms Flow of the average 14K(G.723.1) ~ 51K(G.729) bps Silence Suppression、Voice Activity Detection, Comfort Noise Generator、Acoustic Echo Cancellation、Jitter Buffering、 Other support DTMF tone detection、E.
IPS-2101h User Manual 2. Package Content • One IPS-2101h VoIP Gateway • One Power Adaptor • One RJ-45 Ethernet Cable • One RJ-11 Telephone Cable • Quick Installation Guide • One Installation CD 3. Installation 3.
IPS-2101h User Manual 3.2 Status Button Functions There is a Status Button/Indicator on IPS-2101h indicating different status: Safe Mode: To enter to the safe mode, you can press the Status Button, and then plug into the power. The Status Indicator will flash with green and orange lights. It is used when reloading the firmware from failed firmware. Voice Prompt IP: When the phone hangs up, press the Status Button and then pick up the phone.
IPS-2101h User Manual 4. Hardware Installation The IPS-2101h configured below already has the VoIP account registered on it. If you do not have an account or are unable to register it, please contact to your VoIP service provider. 4.1 Connection with an IP Sharing Device or a Router Deploy this connection when you have an IP sharing device with only one LAN port.
IPS-2101h User Manual 4.2 Connection without an IP Sharing Device or a Router Deploy this connection for those users who are using ADSL PPPoE service and have only one computer. However, the ISP should allow more than two accounts log on the Internet. Place the IPS-2101h between the ADSL modem and your computer. Installation: Plug one end of the RJ-45 cable to one of the LAN port on the IPS-2101h, and plug another end to one of the LAN port of your Hub.
IPS-2101h User Manual 5. Network Settings Using Status Button on IPS-2101h 【The default network setting is DHCP mode】 Press the Status Button on the IPS-2101h, and pick up the handset, you will be able to hear the voice prompt indicating the IP address of your IPS-2101h. If the IP address you hear is 0.0.0.0, then there is no IP address available or the internet connection is bad. Please follow the network settings described below. IPS-2101h can use telephone to configure some simple network settings.
IPS-2101h User Manual 5.3 PPPoE Settings IPS-2101h can not use the Status Button to configure the PPPoE network. Please configure your IPS-2101h with a Static IP (*note) first (refer to 5.1), then use web browser connect to IPS-2101h web configuration page to configure the PPPoE settings. ：In most cases, if your PC has IP address 192.168.1.5, your IPS-2101h can has IP address between 192.168.1.2 to 192.168.1.254 (the first three digits are the same).
IPS-2101h User Manual 6. WEB Configuration Press the Status Button on the IPS-2101h, and pick up the handset, you will be able to hear the voice prompt indicating the IP address of your IPS-2101h. If the IP address you hear is 0.0.0.0, then there is no IP address available or the internet connection is bad. Please refer to “5. Network Settings Using Status Button” to configure the IP address to your IPS-2101h.
IPS-2101h User Manual PPP ID PPP PIN Local IP Subnet Mask Router IP DNS DNS2 6.2 With “PPPoE” selected in the IP Type drop down list, please enter your PPPoE account in this field. With “PPPoE” selected in the IP Type drop down list, please enter your PPPoE password in this field. With “Static” selected in the IP Type drop down list, please enter the IP address for the IPS-2101h in this field.
IPS-2101h User Manual ※ Please do not check this box and leave the Service Addr field blank. If the Gatekeeper is not to be used, please configure the Service Port as 1720. Detailed information please refers to the “Service Port” configuration. For MGCP protocol: Please check this box, and then enter the IP address or domain name of the Call Agent in the Service Addr field. Setup the jitter buffer size for the RTP voice packet. Jitter buffer ensures that the received packets are in correct order.
IPS-2101h User Manual NAT Addr NAT TTL Phone Number SIP traverse the NAT. If this option is selected, please also enter the IP address of the STUN server in the NAT Addr field. When “Enable” or “STUN” is selected in the NAT Traversal field, enter the NAT Proxy’s IP address in this field. Otherwise, keep this field as 0.0.0.0. Define how many seconds a NAT traversal message will be sent to the NAT server. The default setting is 30 seconds, and the maximum is 254. With H.
IPS-2101h User Manual z Control port Register TTL RTP TOS RTP Port Local Type With H.323 protocol used, this port is mapped to the H.245 port. H.245 protocol defines call control signal, and uses TCP protocol. The value can be set from 1024 to 65535. With MGCP or SIP protocol is used, there is no specific request for this port. You can enter any port number. ※ If there are many IPS-2101h traversing the NAT at the same time, each of them should be assigned with different port number.
IPS-2101h User Manual Phone Settings Fields Description Setup the dial plan: • Disable: Not using a dialing plan. • Enable: Use a dialing plan. This dialing plan should combine with the Regional Code and Area Code. Please comply with the E.164 rule to setup the country code, area code and long distance code. • Dialnum Add prefix number in front of the number you want to dial. This option works together with the Dial Number field.
IPS-2101h User Manual Disable the dual mode to allow only IP calls. However, it will switch to PSTN network when blackout. Set the switch key which allows you to switch between PSTN call and IP Dualmode Prefix call when Dual Mode is enabled. Enter a number from 0 through 60 to set the entries of the seconds Answer before the phone answer the call automatically or forward the call. To disable auto answer function, please set this parameter as 0.
IPS-2101h User Manual 6.5 Other Settings Other Settings Field Password Super Password Description Set the user’s password. Should be no longer than 16 digits. Set the administrator’s password. Should be no longer than 16 digits. Firmware auto-upgrade settings: All: Use model name as the identification characters of the upgrade file. Disable: Disable auto-upgrade. Upgrade Type MAC: Use MAC address as the identification characters of the upgrade file.
IPS-2101h User Manual 7. Passing Through the NAT/Firewall When IPS-2101h works with NAT/Firewall, some of the following cases might happen: 1. With a valid account, IPS-2101h can not successfully register to the server. 2. IPS-2101h itself can make calls but is not able to receive calls. 3. One-way talk. One end can not hear any sound. It might be the NAT/Firewall issues in these cases. IPS-2101h supports two methods to allow SIP passing through the NAT/Firewall by deploying STUN or Outbound Proxy.
IPS-2101h User Manual 7.3 Others With H.323 or MGCP protocol is used, please refer to the appendix H.323 and MGCP configuration examples. If IPS-2101h can not work this way, open the corresponding ports on your NAT/Firewall device. Figure below shows the possible usage ports for the IPS-2101h. Please contact to the network administrator or MIS person to open these ports on the NAT/Firewall device: z Register port：For TCP/UDP protocol. z Signal port：For TCP/UDP protocol.
IPS-2101h User Manual 9.3 Other Phone Operation The IPS-2101h has two international standard RJ-11 phone ports which allow you connect to all the standard phones, including traditional wireless phone and DECT wireless phone, with full function on the phone. 10. Firmware Auto-upgrade If auto-upgrade function is enabled (please refer to “6.5 Other Settings”), IPS-2101h will automatically check the designate upgrade server to see if there is new firmware ready for download.
IPS-2101h User Manual 11. Appendix 11.1 H.323 Web Configuration Example With H.323 protocol used, please change the following parameters and leave the other setting as default. (Detailed H.323 information, please contact your VoIP service provider) z Use service：Please check z Service type：Select “common” if not specified by your VoIP service provider. z Service addr：Enter the IP address or the domain name of the Gatekeeper of your VoIP service provider.
IPS-2101h User Manual 11.2 MGCP Web Configuration Example With MGCP protocol used, please change the following parameters and leave the other setting as default. (Detailed MGCP information, please contact your VoIP service provider) z Use service：Please check z Service type：Select “common” if not specified by your VoIP service provider. z Service addr：Enter the IP address or the domain name of the Gatekeeper of your VoIP service provider. z NAT traversal：Select “stun”.
IPS-2101h User Manual 11.3 z z z z z How to Add a Prefix in Front of the Number Use Dialplan：Select “Dialnum”. Dial Number：Enter the prefix you want to add. DDD Code：Blank. IDD Code：Blank. DDD Prefix：Blank. 11.4 For example, 666. Update Information For the latest version manual, please refer to http://www.artdioinc.com/manual.htm For the latest version firmware, please refer to http://www.artdioinc.com/firmware.
IPS-2101h User Manual Los Angeles Office, U.S.A. Address：14235 Lomitas Ave. La Puente, CA 91746 TEL：+ 1- 626 – 336 - 0369 FAX：+ 1- 626 – 961 - 9114 Email：ussales@artdioinc.com Taiwan Headquarter Add：7th FL., No.476, Min-Hu RD., Hsin-Chu, Taiwan 300 TEL：+ 886 – 3 - 5295000 FAX：+ 886 - 3 - 5295005 E-Mail：sales@artdio.com.tw Shanghai Office, China Add：No.8 775 Nong, Hang Dong RD., Shanghai China TEL：+ 86 - 21- 64216757 FAX：+ 86 - 21 - 64206680 E-Mail：shsales@ artdio.com.
