Programming instructions

ManualsBrandsArrowhead ManualsComputer equipmentSK1L

8.278.27

8.27

AUXILIARY CODE REPORT SELECTION (1-8)AUXILIARY CODE REPORT SELECTION (1-8)

AUXILIARY CODE REPORT SELECTION (1-8)

Selection of which auxiliary codes are to be reported to which phone

number. The code for the desired auxiliary code must also be

programmed. Use the following chart to select which of the

sese

venven

ven

groups of items will report their code(s) to the assigned phone

number.

1 Emergency Codes, Duress

2 Open, Close, Station

3 Zone Trouble, AC, Low Battery, Upload

4 History

(For comm(For comm

(For comm

unications to ScanPrunications to ScanPr

unications to ScanPr

o onlo onl

o onl

.).)

5 Test Timer A

6 Test Timer B

7 Zone status, Bypass

EXAMPLE:EXAMPLE:

EXAMPLE:

Sel #1 = 2,7 Reports Open,Close,Station,

Zone status, and Bypass codes to phone # 1.

Sel #2 = 1 Reports Emergency and Duress codes

on phone # 2.

Sel #3 = 4 Reports phone # 3.

Selecting 8 fSelecting 8 f

Selecting 8 f

or eacor eac

or eac

h of the Phone Numberh of the Phone Number

h of the Phone Number

s is fs is f

s is f

or three specialor three special

or three special

optional items and are identified belooptional items and are identified belo

optional items and are identified belo

w:w:

For Phone #1 =Enable for

uto-Armuto-Arm

uto-Arm

For Phone #2 =Allows Incrementing of Account Number by

Partition

For Phone #3 =Disables “Fail to Communicate” indication from

keypad

8.288.28

8.28

ANSWER ON RING NUMBER (0-15)ANSWER ON RING NUMBER (0-15)

ANSWER ON RING NUMBER (0-15)

The system may be programmed to automatically pickup and

answer the telephone line after 1 to 15 rings. This function must be

programmed if remote up/downloading is desired. If an answering

machine is connected to the same phone line as the system, the

system must be programmed for a minimum of 2 rings greater than

the answering machine ring counter. A value of “0” will disable the

ring detector.

8.298.29

8.29

EMERGENCY KEY BELL ENABLE (1-8)EMERGENCY KEY BELL ENABLE (1-8)

EMERGENCY KEY BELL ENABLE (1-8)

If programmed, each emergency key pair can activate the burglary

or fire output. In single bell operation, the Fire bell has priority. Use

the following table to select type of operation. See Keypad Users

Manual for details on use of emergency key pairs.

Key pair Burglary Bell Key pair Fire Bell

(1&3) 1 (1&3) 5

(4&6) 2 (4&6) 6

(7&9) 3 (7&9) 7

(*&#) 4 (*&#) 8

8.308.30

8.30

MISCELLANEOUS SYSTEM FUNCTION SELECTMISCELLANEOUS SYSTEM FUNCTION SELECT

MISCELLANEOUS SYSTEM FUNCTION SELECT

(1-8) - FUNCTION GROUP 1(1-8) - FUNCTION GROUP 1

(1-8) - FUNCTION GROUP 1

Use the following chart to set the first system function group:

1 No EOL resistor 5 Zones 9-16 installed

2 Secure upload 6 2nd

EEPROM INSTALLED

3 Installer privacy code 7 Latched fire bell

4 50 hertz AC 8 Bell shutoff any keypad

1 When this feature is selected, only normally closed burglary

zones can be used.

2 When this feature is selected, the following Up/Download

sequence is performed:

A. A Computer calls the remote system.

B. The remote system acknowledges the call then hangs up.

C. The remote system then calls back Computer (using the

third telephone number) to perform the Up/Download opera-

tion.

3 When this feature is selected and the P1 jumper (located on the

system circuit board) is moved to “program” position,the Install

ers access code is NOT displayed (instead user 1 is displayed).

4 Select this feature when the system is powered from 50 Hz AC

source (i.e. European installations).

5 Select this feature to enable zones 9-16.

6 Select this feature if both

EEPROMS are installed. The 2nd

EEPROM is necessary when Zones 9-16 are installed, 32 user

codes are used, or expanded history is desired.

7 When this feature is selected, an access code must be used to

shut-off the fire bell.

8 When this feature is selected, users at any partition keypad

may silence any alarm that occurs from the system.

8.308.30

8.30

MISCELLANEOUS SYSTEM FUNCTIONMISCELLANEOUS SYSTEM FUNCTION

MISCELLANEOUS SYSTEM FUNCTION

SELECT (1-8) - FUNCTION GROUP 2SELECT (1-8) - FUNCTION GROUP 2

SELECT (1-8) - FUNCTION GROUP 2

Use the following chart to set the second system function group:

1 Automatic bell test 5 Disable auto-scroll

2 Multi-premise 6 Disable ring back

3 Tone dial 7 1 & 3 for smoke reset

4 European rotary dial 8 Enable keypad tamper

1 After the system is armed, the bell(s) turn on for approximately

five seconds. This feature should not be used in a multi-premise

installation.

2 Enable multi-premise operation.

3 Select this digit to enable Tone dialing. When this function is not

programmed, the system defaults to rotary dialing.

4 Enable European rotary dialing (70 millisecond break and 30

millisecond make timing). If not programmed, the system

defaults to standard 60/40 make break rotary dialing.

5 Select this feature to disable keypad status scrolling.

6 Disables ring back to acknowledge a successful transmission.

Ring back is an output from the keypad and remote audible

warning (remote audio piezo).

7 Select this digit to enable smoke reset from the keypad. To

reset, press 1 & 3 simultaneously.

8 Select this digit to enable the keypad tamper switch.

****

** **

NO NO

TE:TE:

TE:

This fThis f

This f

eature is onleature is onl

eature is onl

y ay a

y a

ailabailab

ailab

le fle f

le f

or the Euror the Eur

or the Eur

opeanopean

opean

verver

ver

sions of the SC800/1600 panels.sions of the SC800/1600 panels.

sions of the SC800/1600 panels.

When selected,When selected,

When selected,

the the

the

[*&#] ke[*&#] ke

[*&#] ke

y pair alarm y pair alarm

y pair alarm

WILL NOWILL NO

WILL NO

function. function.

function.