Programming instructions

ManualsBrandsArrowhead ManualsComputer equipmentSK1L

7.9.17.9.1

7.9.1

BELL OPERATIONBELL OPERATION

BELL OPERATION

In multi-premise partitioning, each keypad area 1 through 4, can be

assigned an individual bell, provided a Data Output Board DOB is

installed. If individual bell operation is desired, item thirty (30), third

miscellaneous system function select must be set for a 1 -output bell

module installed.

Refer to DOB (Data Output Board) instructions for installation and

wiring.

In multi-premise partitioning, if a single bell is used and an alarm

occurs, it must be silenced from the keypad associated with the zone

that initiated the alarm, unless "Silence All Area Bells" in Item 30,

First Misc. Select, is set for an eight (8) - Silence All Area Bells.

7.9.27.9.2

7.9.2

FIRE ZONESFIRE ZONES

FIRE ZONES

All fire zones are shared in multi-premise partitioning so that the

alarm condition will be displayed at all locations. The alarm can be

silenced from any keypad area.

arning:arning:

arning:

If this system is used f If this system is used f

If this system is used f

or fire pror fire pr

or fire pr

otection,otection,

otection,

special care special care

special care

ust be taken in the installation,ust be taken in the installation,

ust be taken in the installation,

the sensor selection and their the sensor selection and their

the sensor selection and their

placement.placement.

placement.

Follo Follo

Follo

w all NFPw all NFP

w all NFP

A guidelines and make sure that allA guidelines and make sure that all

A guidelines and make sure that all

system components and wiring are prsystem components and wiring are pr

system components and wiring are pr

otected botected b

otected b

y appry appr

y appr

ved fireved fire

ved fire

sensorsensor

sensor

s.s.

7.9.37.9.3

7.9.3

SHARED ZONESSHARED ZONES

SHARED ZONES

Shared zones are defined as any zones that are required to indicate

status at each of the shared keypads of a partitioned system. The

individual zones to be assigned are placed in Item 52. Activated

24hr. zones may be silenced from any keypad.

o silence an alarm created bo silence an alarm created b

o silence an alarm created b

y a shared by a shared b

y a shared b

urur

glarglar

glar

y zone typey zone type

y zone type

the the

the

eature Silence All Area Bells meature Silence All Area Bells m

eature Silence All Area Bells m

ust be elected in item 30 ofust be elected in item 30 of

ust be elected in item 30 of

prpr

ogramming.ogramming.

ogramming.

7.9.47.9.4

7.9.4

INCREMENTING AINCREMENTING A

INCREMENTING A

CCOUNT NUMBERSCCOUNT NUMBERS

CCOUNT NUMBERS

This feature is only used in multi-premise/partitioned installations

only. This allows the #1 Account number to be incremented by one

(1) for each of the partitions. Global research such as AC loss, Low

Battery, etc. are reported to the #1 Account number. This is enabled

by programming an eight (8) in Item 27, Auxiliary Report Selection

for Telephone #2.

Note: Silent Knight receivers using 4 + 2 format are not compatible

with incrementing account numbers.

7.9.5 AUTO-ARMING7.9.5 AUTO-ARMING

7.9.5 AUTO-ARMING

This is a feature to provide an automatic preselected arming

command to be given to the panel. The selected time is placed in

item 58. It is enabled by placing an (8) in item 27, Auxiliary Report

Selection for Telephone #1. Item #60 must be programmed with

each appropriate day that is required for Auto-Arm to occur. If the

system is be supervised with Open/Close reports, the identifier

when this Auto-Arming occurs is user #8.

Remember:Remember:

Remember:

If A If A

If A

uto Arming is to be used,uto Arming is to be used,

uto Arming is to be used,

select appr select appr

select appr

opriateopriate

opriate

zones fzones f

zones f

or User #8 in item #68 of the pror User #8 in item #68 of the pr

or User #8 in item #68 of the pr

ogramming.ogramming.

ogramming.

If the system were to have a zone in violation at the time of arming

a Force Arm report would be generated. The fourth digit in the Close

code (item #20) is the Force Arm report code and would be

transmitted to the central station. This code would precede the zone

identifier for each of the zone(s) that had been Force Armed.

IT IS HIGHLIT IS HIGHL

IT IS HIGHL

Y RECOMMENDED Y RECOMMENDED

Y RECOMMENDED

O USE O USE

O USE

THE FORCE ARMTHE FORCE ARM

THE FORCE ARM

REPORREPOR

REPOR

TING FEATING FEA

TING FEA

TURE TURE

TURE

WITH WITH

WITH

THE ATHE A

THE A

UTUT

O-ARM FEAO-ARM FEA

O-ARM FEA

TURE TURE

TURE

VERIFY SYSTEM SECURITYVERIFY SYSTEM SECURITY

VERIFY SYSTEM SECURITY

Note:Note:

Note:

If a For If a For

If a For

ce Arm occurce Arm occur

ce Arm occur

s it MUST be unders it MUST be under

s it MUST be under

stoodstood

stood

that the alarm system IS NOthat the alarm system IS NO

that the alarm system IS NO

T SECURE and shouldT SECURE and should

T SECURE and should

be inbe in

be in

vestigated to identify whvestigated to identify wh

vestigated to identify wh

No signal wNo signal w

No signal w

ould beould be

ould be

sent if zone contact was made good since thesent if zone contact was made good since the

sent if zone contact was made good since the

restoral could be a "crestoral could be a "c

restoral could be a "c

losed blosed b

losed b

ut not locut not loc

ut not loc

ked" doorked" door

ked" door

The site should be inspected anThe site should be inspected an

The site should be inspected an

y time that a Fory time that a For

y time that a For

cece

Arm signal is sent.Arm signal is sent.

Arm signal is sent.

7.9.6 CONDITIONAL OPENING SIGNAL7.9.6 CONDITIONAL OPENING SIGNAL

7.9.6 CONDITIONAL OPENING SIGNAL

This is a feature to provide a unique code to the central station when

the system has been disarmed after an alarm has occurred. This

would signify to the central station that someone was at the site with

a viable access code. The code generated will be, the digit 1 or 2 in

item #21, followed by the appropriate user code.

Note:Note:

Note:

This fThis f

This f

eature eature

eature

WILL NOWILL NO

WILL NO

T wT w

T w

ork in conjunction with Open/ork in conjunction with Open/

ork in conjunction with Open/

CloseClose

7.10 PANEL OPERATION USING THE SCANPRO7.10 PANEL OPERATION USING THE SCANPRO

7.10 PANEL OPERATION USING THE SCANPRO

DOWNLOADER SOFTWAREDOWNLOADER SOFTWARE

DOWNLOADER SOFTWARE

The panel can be accessed, status viewed and remotely Armed/

Disarmed using the ScanPro Downloader software. If the software

is used to Arm or Disarm and Open/Closes has been selected the

central station will receive the user identifier for user 15.

If Open/Close reporIf Open/Close repor

If Open/Close repor

ting is selected and ScanPrting is selected and ScanPr

ting is selected and ScanPr

o is used to Armo is used to Arm

o is used to Arm

or Disarm the system the Upload/Door Disarm the system the Upload/Do

or Disarm the system the Upload/Do

wnload Code should bewnload Code should be

wnload Code should be

enabenab

enab

led with a special digit so that it wled with a special digit so that it w

led with a special digit so that it w

ould accompanould accompan

ould accompan

y they the

y the

User 15 reporUser 15 repor

User 15 repor

ting codeting code

ting code

This wThis w

This w

ould alloould allo

ould allo

w the central station tow the central station to

w the central station to

be abbe ab

be ab

le to diffle to diff

le to diff

erentiate the twerentiate the tw

erentiate the tw

o usero user

o user

s.s.