Programming instructions

ManualsBrandsArrowhead ManualsComputer equipmentSK1L

SECTION 3:SECTION 3:

SECTION 3:

SETUP AND SETUP AND

SETUP AND

TESTING SYSTEMTESTING SYSTEM

TESTING SYSTEM

3.13.1

3.1

POWERING UP THE CONTROLPOWERING UP THE CONTROL

POWERING UP THE CONTROL

Before applying power to the system, recheck all wiring connec-

tions, verifying polarity.

Plug the AC transformer into an

unswitched 120vac receptacle.

Connect the battery leads to the battery. Red lead to the positive (+)

terminal, black lead to the negative (-) terminal of the battery. If the

battery is not fully charged, allow 36 hours for the battery to fully

charge. The keypad will now display system status.

NONO

TE:TE:

TE:

Re Re

verver

ver

sing battersing batter

sing batter

y wires will cause the factory wires will cause the factor

y wires will cause the factor

y replace-y replace-

y replace-

abab

le fuse FL1 to ble fuse FL1 to b

le fuse FL1 to b

lolo

Program the EEPROM for the desired system configuration and

features. Refer to the SC programming instructions, Section

8 of

this manual. After programming is complete, restore the system

back to the normal mode.

3.23.2

3.2

TESTING THE LOCAL SYSTEMTESTING THE LOCAL SYSTEM

TESTING THE LOCAL SYSTEM

The system can be armed and disarmed from the keypad using the

factory default code [1111] or any user code previously assigned.

The system may also be armed and disarmed using a keyswitch,

if so programmed. Leave the system disarmed.

NONO

TE:TE:

TE:

BefBef

Bef

ore testing commore testing comm

ore testing comm

unication to the centralunication to the central

unication to the central

reporrepor

repor

ting station,ting station,

ting station,

connect the telephone connection connect the telephone connection

connect the telephone connection

cabcab

cab

le into the RJ31-X jacle into the RJ31-X jac

le into the RJ31-X jac

k.k.

Testing the system using the keypad:

Arm the system in the test mode.

Press

[PPPP] + [PPPP] +

[PPPP] +

▲

■

▲

The audible warning device will pulsate continuously during TEST,

except when testing an Entrance Delay zone. During Entrance Delay

time, the audible warning device will change to a steady sound (for

4 seconds in the TEST MODE), and then return to a pulsating sound.

All loops may now be tested independently. Violate each loop

separately. The Arm led will flash and the zone in alarm will be

indicated. No need to reset panel after each zone test. Bell or Siren

will shut off in 4 seconds and another zone can be tested.

NONO

TE:TE:

TE:

Zones violated while in the Zones violated while in the

Zones violated while in the

TEST MODE will not reporTEST MODE will not repor

TEST MODE will not repor

to the Central Reporto the Central Repor

to the Central Repor

ting Station.ting Station.

ting Station.

After all zones are tested, After all zones are tested,

After all zones are tested,

Disarm the panel.Disarm the panel.

Disarm the panel.

All audib All audib

All audib

le warning dele warning de

le warning de

vices will shut off andvices will shut off and

vices will shut off and

the Arm LED will turn offthe Arm LED will turn off

the Arm LED will turn off

THE THE

THE

TEST MODE IS NOTEST MODE IS NO

TEST MODE IS NO

T AT A

T A

AILABLE IN AILABLE IN

AILABLE IN

THE MULTHE MUL

THE MUL

TI-PREMISETI-PREMISE

TI-PREMISE

ARAR

TITION MODE TITION MODE

TITION MODE

BUT BUT

BUT

THE COMMAND CAN BE USED THE COMMAND CAN BE USED

THE COMMAND CAN BE USED

CLEAR A "FCLEAR A "F

CLEAR A "F

AIL AIL

AIL

O COMMUNICAO COMMUNICA

O COMMUNICA

TE" INDICATE" INDICA

TE" INDICA

TION.TION.

TION.

3.33.3

3.3

TESTING COMMUNICATION TO THE CENTRALTESTING COMMUNICATION TO THE CENTRAL

TESTING COMMUNICATION TO THE CENTRAL

REPORTING STATIONREPORTING STATION

REPORTING STATION

Arm the panel. Violate a zone. The Siren/Bell should turn on, the arm

led will flash and the zone in alarm will be indicated, the premise

telephone should be inoperative (DEAD). After the Central Report-

ing Station receives a good transmission of this violation, it will send

a "Kiss-off" signal back to the panel and disconnect from the

telephone line, returning premise phone back to normal.