SK1L LCD KEYPAD Owner's Manual use with SC800 & SC1600 Control panels IT IS IMPORTANT FOR YOUR SAFETY TO TEST YOUR SYSTEM AND IT'S COMPONENTS REGULARLY.
General Description The SK1L is a digital arming station that provides full system control and displays full system status from one or more convenient locations. A brief description of the functions of each light and the LCD display is shown in Figure 1. Additionally, built into each SK1L is a miniature sounding device which, when active, indicates various conditions such as a Pre-Alarm Warning, Fault Condition, Test Modes of operation, or Door Annunciation.
System Configuration This page should be marked by your installer at the time of installation to define the Panel that was installed, and the options that were programmed.
--Green READY Light when ON indicates that all protected areas are secure and system is ready to be armed. A blinking ready light indicates a Fault Condition. --Red General ARMED Light when ON indicates system is armed or on. A blinking armed light indicates that an alarm has occurred. --The "LCD DISPLAY" indicates system status in Alpha Numeric characters, with zone arming, zone bypassing, alarms and trouble conditions all being displayed.
RECOMMENDATION: If, when arriving home, the burglar alarm is sounding, contact police from a nearby location. DO NOT ENTER YOUR RESIDENCE. Arming System with Ready Light On or Off If the READY light is on, all zones may be armed by entering your Access Code, using the key sequence in Figure 3. If the READY light is not on you must either go and close the door or window that is open or BYPASS the zone and eliminate it from the system for this ARMING.
All the other burglary zones except zone 3 will ARM and the display will show ARMED. Zone 3 is now deactivated. If the window is closed and opened again, an alarm condition will not result, as this zone will be bypassed until the system is disarmed and rearmed. When the system is disarmed the bypass is removed. Zone Bypass (cont'd) Bypassing zones with zone numbers higher than 9 require the use of the "Two Digit" key pair prior to inputting the zone number.
Figure 7 Instant/Delay Mode The system will normally arm in the Delay Mode when leaving the premises. This will delay arming, allowing time to exit. When entering, the alarm will be delayed allowing time to disarm the system. The audible warning device will sound during the entrance delay reminding you to disarm the system. The Instant Mode is primarily used in residences. It is used during sleeping hours when an entrance delay is not wanted.
The LCD display will be scrolling through the zones that were tripped.To exit test mode enter your access code. It is important for your safety that you test your system regularly. Testing Communicator Check with your installer as to how to test, and how often to test the communicator portion of your system. Various central monitoring stations have different procedures for testing the communicator. Your installer is familiar with this procedure.
Chime Mode Your installer may have designated certain burglary zones to briefly activate the mini-sounder contained in each keypad. These zones typically annunciate that a door has been opened or closed while the panel was disarmed. To turn on the chime operation, enter the following key sequence: Figure 10 If chime operation is not desired, simply enter the following key sequence: Figure 11 Fault Condition A Fault Condition could, if unheeded, potentially render your system inactive.
AC OFF: Indicates the A.C. power to your alarm system has been disrupted. LOW BATTERY: Indicates a low battery condition FAIL COMMUNICATE: Indicates failure to communicate to the central monitoring station. IT IS IMPORTANT FOR YOUR SAFETY THAT YOU HAVE YOUR INSTALLER CORRECT ANY FAULTS AS SOON AS POSSIBLE. Duress (Ambush) Duress is used during a hold-up when youre ordered to disarm your system. When used, a silent alarm is transmitted to the central monitoring station.
Emergency Alarm Key Pairs There are four special emergency codes that can be initiated at the keypad. THESE EMERGENCY ALARM KEY PAIRS MUST BE PRESSED SIMULTANEOUSLY, (a feature designed to minimize false alarms). . For example: Pressing the ENTER# first and then pressing the STAR* key while the ENTER# is still held down will NOT send an emergency signal. The special key pair combinations are marked with a circle, square, diamond, or triangle.
Partitioned Mode Your installer/dealer may have assigned specific zone(s) for you. Other users are sharing the same alarm system. There is very little interaction between users, and arming and bypassing zones can be done without interfering with other users. Bypassing zones is explained in the section on conventional mode. Entering the Access Code and then pressing ENTER# will arm or disarm all of your zones.
Remote Downloader Functions The panel can be programmed over the phone line using a computer. There are times when you may be instructed by the Monitoring Center to use one of these special commands for that purpose. The panel can be instructed to call the computer or to answer when the computer calls. These functions should only be used when instructed to do so by personnel at either the Monitoring Center or Installation Company.
Emergency Evacuation Plan The National Fire Protection Agency recommends the following guidelines to be prepared for an actual fire. 1. Draw a floor plan of the building marking all doors and windows. 2. Evaluate all possible escape routes from building, trying each route. 3. Select two (2) escape routes from each room. 4. Second floor rooms should have a rope ladder that reaches the ground. 5. Draw a sketch of the escape route and familiarize everyone in the home with it. 6.
WARRANTY AND LIABILITY LIMITATIONS AND DISCLAIMER LIMITED WARRANTY Sentrol, Inc. warrants to the purchaser that under normal use and service, its products will be free from defects in material and workmanship as follows: Control Panels and accessories - 24 months from date of manufacture; Sensors and accessories - 60 months from date of manufacture. Sentrol, Inc.’s warranty obligation is limited to repairing or replacing (at Sentrol, Inc.
DISCLAIMER OF WARRANTIES THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PURCHASE. ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. NO OTHER PERSON OR ENTITY HAS BEEN AUTHORIZED BY SENTROL, INC. TO MODIFY OR CHANGE THE TERMS OF THIS WARRANTY.
