Owner`s manual

nication. Le materiel doit egalement etre installe en suivant une method acceptee de raccordement.Dans certains cas, les fils interieurs
de l’entreprise utilises pour un service individuel a ligne unique peuvent etre prolonges au moyen d’un dispositif homologue de raccordement
(cordon prolongateur telephonique interne). L’abonne ne doit pas oublier qu’il estpossible que la conformite aux conditions enoncees ci-
dessus n’empechent pas la degradation du service dans certains situations. Actuellement, les entreprises detelecommunication ne permettent
pas que l’on raccorde leur materiel a des jacks d’abonne, sauf dans les cas precisprevus pas les tarrifs particuliers de ces entreprises.
Les reparations de materiel homologue doivent etre effectuees pas un centre d’entretien canadien autorise designe par le fournisseur. La
compagnie de telecommunications peut demander a l’utilisateur dedegbrancher un appareil a la suite de reparations ou de modifications
effectuees par l’utilisateur ou acause de mauvais fonctionnement.
Pour sa propre protection, l’utilisateur doit s’assurerque tous les fils de mise a la terre de la source d’energie electrique, des lignes telephonique
et de scanalisations d’eau metalliques, s’il y en a, sontraccordes ensemble. Cette precaution est particulierement importante dans les regions
rurales.
AVERTISSEMENT. - L’utilisateur ne doit pas tenter de faire ces raccordements lui-meme; il doit avoir recoursa un service d’inspection
des installation selectriques, ou a electricien, seelon le cas.
L’indice de charge (IC) assigne a chaquedispositif terminal indique, pour evciter toutesurcharge, le pourcentage de la charge totale quipeut
etre raccordee a un circuit telephoniqueboucle utilise par ce dispositif. La terminaison du circuit boucle peut etre constituee de n’importquelle
combinaison de dispositifs, pourvu que lasomme des indices de charge de l’ensemble de sdispositifs ne despasse pas 100.
L’Indice de charge de cet produit est 4.
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the radio interference
regulations of the Canadian Department of Communications.
Le present appareil numerique n’emet pas de bruits radioelectriques despassant les limites applicables aux appareils numeriques de Classe
B prescrites dans le reglement sur le brouillage radioelectriques edicte par le Ministere des Communications du Canada.
UL COMPLIANCE
Follow the instructions below when installing and programming an AV9000 Alarm Control Panel to meet installation requirements.
HARDWARE CONSIDERATIONS FOR UL COMPLIANCE
1. Do not plug the Basler transformer into a receptacle controlled by a switch.
2. Use a 12 volt 7AH battery (Yuasa NP7-12) in order to have a standby time of at least 4 hours.
3. Use a UL listed bell across terminals 8 and 9. Terminals 8 and 10 are not to be used for a sounding output device since a constant and
pulsing output is not available.
4. Maximum combined Auxiliary, keypad, and fire outputs (terminals 4, 5 and 11) is 400 mA at 12.5 VDC.
5. Use P/N EOL 2200 end-of-line resistor (optional) for all fire zones and P/N 123-000222 (enclosed) for all burglary type zones of protection.
6. Maximum bell load is 300mA at 12.5 VDC. Use UL listed Bell or sounding device. Suggested Bells: Wheelock MB-G10-12-R or
Amseco MSB-10G.
7. Use UL listed 9-14VDC 4-wire smoke detector and UL listed end-of-line relay module.
8. The optional single or double gang plastic GEM box used for mounting the EKP1 keypad must be UL listed.
9. Use a UL listed momentary keyswitch if keyswitch operation is desired. A UL Listed EKP1 or EKP1L keypad must still be used with
the system and both must be installed within the protected area.
10. Keypads must be installed within the protected area.
11. Tamper switch must be installed on the control panel cabinet.
PROGRAMMING CONSIDERATIONS FOR UL COMPLIANCE
1. Maximum Exit time allowed is 60 seconds. (Memory Location 130 and/or 131).
2. Maximum Entry time allowed is 40 seconds. (Memory Location 128 and/or 129).
3. Program all alarm sounding devices to operate for a minimum of 4 minutes. (Memory Location 132).
4. Program manual shutdown on the fire alarm time out. (Memory Location 205 should select a “7”).
5. Program Fire power reset through the keypad (1 & 3). (Memory Location 206 should select a “7”).
6. Program the panel to report to the Central Station on loss of AC power and low battery. (Memory Locations 116, 117, 114, 115, 134 190 and/
or 191).
7. Program the panel to report all fire zone trouble conditions to the Central Station. (Memory Location 101, 190 and/or 191).
8. Dialing attempts for 1 and 2 must be a minimum of 5 and a maximum of 10 attempts. (Memory Location 143).
9. Test message interval must be programmed to 1 every 24 hours. (Memory Locations 136-140, 190-192 and 122-123).
10. Single bell operation must be programmed in order to get a pulsing output for fire and constant output on burglary violations. (Memory
Location 141 should be anything but a blank and Location 142 should be blank).
11. 24 hour fire zones cannot be programmed as bypassable zones.
12. For correct dialer report prioritization, fire zones are to be assigned to the lower numbered zones, Panics on the next lowest numbered
zones, and burglary zones on the highest numbers. Example: Zone 1 = Fire, Zone 2 = Panic, zones 3-8 = burglary.