Owner`s manual

25
SECTION 4: COMPLIANCE
INFORMATION TO USER
This equipment generates and uses radio frequency energy and if not installed and used properly, that is in strict accordance with the
manufacturer’s instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the
limits for a Class B computing device in accordance with the specifications of Subpart J of part 15 of FCC rules, which are designed to provide
reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient the TV or radio antenna.
2. Relocate or move the alarm control away from the receiver.
3. Plug the transformer for the alarm control into a different outlet so that the receiver and the alarm are on different branch circuits.
4. If necessary, the user should consult the alarm dealer or an experienced radio/television technician for additional suggestions. The user
may find the following booklet prepared by the Federal Communications Commission helpful, “How to Identify and Resolve Radio-TV Interfer-
ence Problems.” This booklet is available from the U.S. Government Printing Office - Washington, DC, 20402, Stock #004-000-00345-4.
FCC COMPLIANCE
This equipment complies with Part 68 of the FCC Rules. On the bottom of this equipment is a label that contains, among other information, the
FCC Registration Number and Ringer Equivalence Number (REN) for this equipment. You must, upon request, provide this information to your
telephone company.
The REN is useful to determine the quantity of devices you may connect to your telephone line and still have all of this devices ring when
your telephone number is called. In most, but not all areas, the sum of the REN’s of all devices connected to one line should not exceed five
(5.0). To be certain of the number of devices you should contact your local telephone company to determine the maximum REN for your calling
area.
If your telephone equipment causes harm to the telephone network, the Telephone Company may discontinue your service temporarily.
If possible, they will notify you in advance, but if advance notice is not practical, you will be notified as soon as possible. You will be informed of
your right to file a complaint with the FCC.
Your telephone company may make any changes in it’s facilities, equipment, operations or procedures that could affect the proper
functioning of your equipment. If they do, you will be notified in advance to give you an opportunity to maintain uninterrupted telephone service.
If you experience trouble with this telephone equipment, please contact Sentrol, Inc. P.O. Box 2904, Hickory, N.C. 28601, for information
on obtaining service or repairs. The telephone company may ask that you disconnect this equipment from the network until the problem has
been corrected or until you are sure that the equipment is not malfunctioning.
This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs.
Installations: This device requires a USOC RJ31X jack.
CANADIAN INSTALLATIONS
NOTE: The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment
meets certain telecommunications network protective, operational and safety requirements. The Department does not guarantee the equip-
ment will operate to the user’s satisfaction.
Before installing the equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications
company. The equipment must also be installed using an acceptable method of connection. In some cases, the company’s inside wiring
associated with a single line individual service may be extended by means of a certified connector assembly (telephone extension cord). The
customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or
alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the
user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic
water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspec-
tion authority, or electrician as appropriate.
The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which
is used by the device to prevent overloading. The termination on the loop may consist of any combination of devices subject only to the
requirements that the total of the Load Numbers of all the devices does not exceed 100. The load number for this equipment is LN = 4.
AVIS: L’etiquette du ministere des Communications du Canada identifie le materiel homologue. Cette etiquette certifie que le
materiel est conforme a certaines normesde protection, d’exploitation ed de securite des reseauxde telecommunications. Le
Ministere n’assure toutefois pas que le materiel fonctionnera a la satisfaction del’utilisateur.
Avant d’installer ce materiel, l’utilisateur doit s’assurer qu’il est permis de le raccorder aux installatyons de ‘l’entreprise locale de telecommu-