Owner's Manual & Assembly Instructions BS1 Model No. YS410-A 697.68602 Missing Parts, Questions on Assembly? Call: 1-800-851-1085 Do not return to dealer, they are not equipped to handle your requests. 707741209 Storage Area: 38 Sq. Ft. 3,5 m2 227 Cu. Ft. 6,4 m3 BUILDING DIMENSIONS * Size rounded off to the nearest foot *Approx.
BEFORE YOU BEGIN.... A2 Owner's Manual Before beginning construction, check local building codes regarding footings, location and other requirements. Study and understand this owner's manual. Important information and helpful tips will make your construction easier and more enjoyable. Instructions are supplied in this manual and contain all appropriate information for your building model.
PLAN AHEAD.... A3 Watch the Weather: Be sure the day you select to install your building is dry and calm. Do not attempt to assemble your building on a windy day. Be careful on wet or muddy ground. Whenever possible, two or more people should work together to assemble your building. One person can position parts or panels while the other is able to handle the fasteners and the tools. Teamwork: These are some basic tools and materials you will need for the construction of your building.
SAFETY FIRST.... A4 Safety precautions are important to follow throughout the construction of your building. •Care must be taken when handling various pieces of your building since some contain sharp edges. Please wear work gloves, eye protection and long sleeves when assembling or performing any maintenance on your building. •Practice caution with the tools being used in the assembly of this building. Be familiar with the operation of all power tools.
CARE & MAINTENANCE.... A5 Web For long lasting finish, periodically clean and wax the exterior surface. Touchup scratches as soon as you notice them on your unit. Immediately clean the area with a wire brush; wash it and apply touch-up paint per manufacturer's recommendation. Finish: Roof: Keep roof clear of leaves and snow with long handled, soft-bristled broom. Heavy amounts of snow on roof can damage building making it unsafe to enter.
ACCESSORIES.... A6 WEB ROOF STRENGTHENING (heavy snow load) KITS FLOOR FRAME KITS Extra roof beams and gable braces designed for added protection against heavy snow accumulation. Increases the strength of your roof by 50%. ANCHOR KITS Model No. AK4 Anchor Kit contains heavy-duty steel augers, 60' (18 m) of steel cable and 4 cable clamps. No digging or concrete pouring, just insert cable under roof, over roof beams, into augers and twist augers into the ground.
THIS PAGE WAS LEFT BLANK INTENTIONALLY
THIS PAGE WAS LEFT BLANK INTENTIONALLY
Base BS09 The Base For Your Building OPTION 1: ARROW FLOOR FRAME KIT: (Order No. FB47410) Arrow has the best base for your building in this simple kit. It keeps stored items above the ground. This kit should be used with one of the following: A. To support a plywood deck B. To be filled with sand. We recommend the combined use of 1. an ARROW FLOOR FRAME KIT and 2. an ARROW ANCHORING KIT as an effective method of securing the building to the ground. Allow 1 - 2 hours for construction.
Anchoring BR10 Anchoring Down The Building It is important that the entire floor frame be anchored after the building is erected. Below are recommended ways of anchoring. Anchoring into Wood/Post: Use 1/4" (6 mm) Wood Screws. There are 1/4" (6 mm) dia. holes provided in the frames for proper anchoring. Arrow Anchoring Kit: (Model No. AK100 or 68383) Recommended for use with the concrete base. Contains: Corner gussets, perimeter clips, hardware, 1/4" masonary drill bit and installation instruction.
Hardware BS11 65103 #8-32 Hex Nut (66) 65941 #6-32 Hex Nut (23) (Packed with Screws) 65923 #8-32x3/8" (10 mm) Bolt (66) 65004 #8Ax5/16" (8 mm) Screw (302) 66714 #6-32x7/16" (11 mm) Flat Hd Bolt (16) (Packed with Screws) 66645 #6-32x3/4" (19 mm) Flat Hd Bolt (7) (Packed with Screws) 66646 Washer (278) (8 sheets of 40) 66022 Gray Foam Tape (1) 66684 Spring Latch (2) 66462 Hasp (1) 66016 Facia Cap (1 Right and 1 Left) 66463 Swivel Staple (1) 66604 Hinge (4) 66057 Trim Cap (1) 67293 Foil Tape (1)
Parts List BS12 Assembly Key No.
Assembly by Key No.
Step 1 ● 9794 Horizontal Door Brace (4) ● 9788 Right Door (1) ● 9787 Left Door (1) ● 67729 Foam Board (2) ● Parts Needed For ● Door Assembly BR14 END VIEW #6-32x3/4" (19 mm) Flat Head Bolt Hasp #6 Hex Nut Foil Tape 1 Position hinges on sides of right and left door panels as shown and fasten with 7/16" (11 mm) flat head bolts outside and #6 hex nuts inside. 2 Slide foam board into door pan- STEP els, foil facing outward, equally spaced on both sides. See caution.
Step 2 ● 9796 Ramp (1) ● 9795 Floor Frame (2) ● 8976 Side Floor Frame (4) ● Parts Needed For ● Floor Frame Assembly BS15 1 Overlap the side floor frames as shown. The holes in these pieces will align when the pieces are positioned with correct amount of overlap. See the illustration below for the proper overall length of the side floor frames. Join the frames by inserting five bolts and nuts in each frame set as shown.
● Parts Needed For ● Step 3 Corner Posts/Rear Siding ● 9793 Corner Post (2) ● 8075 Rear Siding (1) BR16 NOTE The remainder of the building assembly requires many hours and more than one person. Do not continue beyond this point if you do not have enough time to complete the assembly today. A partially assembled building can be severely damaged by light winds. 9793 9793 1 Fasten two corner posts to the rear corners of the floor frame assembly using four screws.
● 6481 Gusset (4) ● 9793 Corner Post (2) ● 8433 Siding Stud (1) ● 8434 Siding Stud (1) ● 8431 Side Siding (4) ● Parts Needed For ● Step 4 Corner Posts/Studs/Siding BS17 1 Attach a gusset to each end of the two corner posts using one screw. TOP VIEW 2 Fasten one corner post assembly to the front corner of the floor frame assembly using two screws. Lightly fasten tab end of siding stud to side floor frame using two screws.
● Parts Needed For ● Step 5 Headers/Frames/Jambs BS18 1 Fasten side eave frames behind top of corner post with a bolt and nut, and over siding stud using a screw, top leg facing inside building. Note: For left end door location, fasten side eave frames as shown. For right end door location fasten side eave frames on opposite side of building.
● 8431 Side Siding (4) ● 8075 Rear Siding (1) ● 8067 Siding Stud (5) ● 8068 Siding Stud (4) ● Parts Needed For ● Step 6 Side/Rear Siding/Studs BS19 1 Position the side siding (6 board) STEP 2 to corner posts and stud, flat edge of siding upward and bottom resting on 1st side siding. See figure. Always follow this pattern. Fasten siding to corner posts using screws and stud using bolts and nuts. Do not fasten flat edge now. Position 2nd side siding on opposite side of building and fasten as before.
● 8061 Left Gable (1) ● 8060 Right Gable (1) ● 8438 Side Peak Frame (2) ● 8066 Roof Frame (4) ● 8435 Roof Frame (1) ● Parts Needed For ● Step 7 Gables/Peak/Roof Frames BS20 NOTE The gables are packed nested together and might be mistaken as one piece. Carefully separate them before continuing. Side Peak Frame Fasten at Lower Hole Position of Side Peak Frame 1 Lift and fasten a left gable on top STEP of header, with lower leg under side eave frame at corner, using screws.
● Parts Needed For ● Step 8 ● 8431 Side Siding (4) Side Siding/Foam Tape BS21 Foam Tape Installing the siding to the roof is best done with a step ladder. 4th Side Siding NOTE Measure the building diagonally again and make adjustments to make sure the building is square. This will make the siding fit better, and holes will align. Protective Paper Apply Gray Foam Tape STEP 1 After the 3rd side siding is fastened to the 2nd, roll it over on the roof and fasten as before.
Step 9 ● 8432 Top Siding (2) ● 8439 Peak Trim (2) ● 8442 Rear Siding Trim (1) ● 8078 Right Wall Trim (1) ● 8079 Left Wall Trim (1) ● 8076 Right Roof Trim (1) ● Parts Needed For ● Top Siding/Trim BS22 ● 8077 Left Roof Trim (1) ● 8440 Bottom Siding Trim (1) ● 8441 Top Siding Trim (1) 1 Fasten remaining top siding (5 board), to the top side of building. STEP STEP 2 Fasten peak trim to peak of roof STEP using screws thru siding into frame.
● Parts Needed For ● Step 10 Door Stop ● Right Door Assembly (1) ● Left Door Assembly (1) ● 9792 Door Stop (1) BR23 1 Position doors in corners of door opening as shown and fasten hinges with 7/16" (11 mm) flat head bolts and #6 hex nuts. Be sure the heads on hinge pins are all installed toward top. 2 Position door stop to left door, with tapered end up and hems toward inside of building, and fasten using four screws. Fasten a spring latch at the top and bottom of door stop, using three screws.
Anchoring and Floor Frame BR24 Anchoring Anchor your building at this time. Floor Frame If you have purchased a Floor Frame Kit you need to install it at this time.
SOME FACTS ABOUT RUST XA35hw SOME FACTS ABOUT RUST Rusting is a natural oxidizing process that occurs when bare metal is exposed to moisture. Problem areas include screw holes, unfinished edges, or where scrapes and nicks occur in the protective coating through normal assembly, handling and use. Identifying these natural rusting problem areas and taking some simple rust protection precautions can help to stop rust from developing, or stop it quickly as soon as it appears. 1.
