HT55™ HAMMER TACKER ENGLISH Click Button to go to page SAFETEY RULES.................................................................................................. P2 HOW TO LOAD STAPLES....................................................................................... P 3 ABOUT STAPLES.................................................................................................. P4 MAINTENANCE & ACCESSORIES........................................................................
SAFETY RULES • Always be cautious of potential hazards such as electrical wiring, slippery footing, damp or wet conditions, etc. • Make sure you know what you are fastening — look for hidden hazards. • Keep work area clean. Cluttered areas and benches invite accidents. • Keep children away. All visitors should be kept a safe distance from work area. • Store idle tools. When not in use, tools should be stored in high or locked-up place — out of reach of children. • Use safety glasses. • Do not overreach.
HOW TO LOAD STAPLES TO LOAD 1. Remove pusher rod from machine by pushing in and up, then pulling out. 2. Insert strip of staples. 3. Replace pusher rod. TO CLEAN STAPLE CHANNEL 1. Remove pusher rod “A” and any remaining staples. 2. While squeezing front end of tool “B”. remove pin “C”. Pin “C” is reversable for right or left handed operation. 3. Pull out entire staple chamber “D” to clean or clear jams. 4. When replacing staple chamber squeeze together as shown “B” and replace Pin “C”.
ABOUT STAPLES HOW TO DETERMINE PROPER STAPLE LEG SIZE In choosing the proper staple leg length for a job there are two basic things to consider: 1. Thickness of material to be stapled. 2. Hardness of the wood. As a general rule, in hardwood, approximately 3/16" to 1/4" penetration into the wood is sufficient...and for softwood – up to approximately 3/8" should be sufficient. However, if the staple used “stands away” from the work – this means that too long a leg length has been used.
MAINTENANCE Your HT55™ is virtually maintenance free. Keep tool clean and free of dust. Wipe clean with a dry cloth do not use harsh chemicals to clean your HT55™. In the unlikely event that you should need service, contact: Arrow Fastener Co., LLC 271 Mayhill Street, Saddle Brook, N.J. 07663 Tel. 201-843-6900 ACCESSORIES Arrow accessories and genuine Arrow T50® Staples are available at retail outlets, hardware stores, lumberyards and wherever fine tools are sold.
REGLAS DE SEGURIDAD • Siempré debe estar alerta a posibles riesgos tales como cables electricos, pisos resbalosos, condiciones humedas o mojadas, etc. • Asegúrese de saber lo que esta fijando, esté pendiente de riesgos ocultos. • Mantenga limpia el área de trabajo. Las áreas y bancas desordenadas propician accidentes. • Mantenga alejados a los niños. Todo visitante debe permanecer a una distancia del área que no presente peligros. • Almacene las herramientas que no están en uso.
CÓMO CARGAR GRAPAS TO LOAD 1. Remove pusher rod from machine by pushing in and up, then pulling out. 2. Insert strip of staples. 3. Replace pusher rod. TO CLEAN STAPLE CHANNEL 1. Remove pusher rod “A” and any remaining staples. 2. While squeezing front end of tool “B”. remove pin “C”. Pin “C” is reversable for right or left handed operation. 3. Pull out entire staple chamber “D” to clean or clear jams. 4. When replacing staple chamber squeeze together as shown “B” and replace Pin “C”.
SOBRE GRAPAS COMO DETERMINAR EL TAMAÑO DE PATA DE LA GRAPA PROPIO Para escojer el tamaño de pata de la grapa apropiada para el trabajo – hay dos cosas básicas que considerar: 1. Espesor del material quese va a engrapar. 2. Dureza de la madera. Como regla general, en maderas duras, una penetración en la madera de 3/16" a 1/4" es suficiente...y para maderas blandas hasta approximadamente 3/8" debe ser suficiente.
MANTENIMIENTO Su HT55™ prácticamente no necesita mantenimiento. Mantenga su herramienta limpia y libre de polvo. No utilice químicos agresivos para limpiar su HT55™, sólo use un paño seco. En el improbable caso de que usted debe necesitar servicio, póngase en contacto con: Arrow Fastener Co., LLC 271 Mayhill Street, Saddle Brook, N.J. 07663 Tel.
INSTRUCTIONS DE SÉCURITÉ • Soyez toujours vigilant à cause de possibles sources de danger tels que les câblages electriques, les sols glissants. I’humidité, etc. • Assurez-vous de bien connaître le produit que vous fixez cherchez les dangers cachés. • Veillez à ce que l’aire de travail soit propre. Les locaux et plans de travail encombrés sont propicés aux accidents. • Veillez à ce que les enfants restent a l’écart. Tous les visiteurs doivent se tenir à une distance raisonnable des zones de travail.
COMMENT CHARGER DES AGRAFES TO LOAD 1. Remove pusher rod from machine by pushing in and up, then pulling out. 2. Insert strip of staples. 3. Replace pusher rod. TO CLEAN STAPLE CHANNEL 1. Remove pusher rod “A” and any remaining staples. 2. While squeezing front end of tool “B”. remove pin “C”. Pin “C” is reversable for right or left handed operation. 3. Pull out entire staple chamber “D” to clean or clear jams. 4. When replacing staple chamber squeeze together as shown “B” and replace Pin “C”.
AU SUJET DES AGRAFES COMMENT CHOISIR L’A GRAFE APPROPRIÉE AU TRAVAIL À RÉALISER. Le choix de l’agrafe dépend de deux éléments: 1. L’épaisseur du matériau à agrafer. 2. La résistance du bois.En règle générale, avec les bois durs il faut utiliser des agrafes de 6mm à 8mm. Pour les bois tendre des agrafes 10mm suffisent. Cependant s’il y a un espace entre l’agrafe et le matériau cela signifie qu’une patte d’agrafe trop longue a été employée.
ENTRETIEN Votre HT55™ ne nécessite pratiquement aucune maintenance. Conservez l'outil propre et dépoussiéré. Essuyez avec un chiffon sec et n'employez pas de produits chimiques abrasifs pour nettoyer votre HT55™. Dans le cas peu probable où vous avez besoin de service, contactez: Arrow Fastener Co., LLC 271 Mayhill Street, Saddle Brook, N.J. 07663 Tel.
