Owner's Manual & Assembly Instructions C01 Model No. EN65-A HM65S ENB65 NW65 709311207 BUILDING DIMENSIONS * Size rounded off to the nearest foot *Approx. Size Foundation Size 6' x 5' 74" x 57" 1,8m x 1,4m 188cm x 145cm Storage Area Sq. Ft. Cu. Ft. 27 2,5m2 142 4,0m3 HM65-A SA65-A CAUTION: SOME PARTS HAVE SHARP EDGES. CARE MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ SAFETY INFORMATION PROVIDED IN THIS MANUAL BEFORE BEGINNING CONSTRUCTION.
BEFORE YOU BEGIN.... A2 Owner's Manual Before beginning construction, check local building codes regarding footings, location and other requirements. Study and understand this owner's manual. Important information and helpful tips will make your construction easier and more enjoyable. Assembly Instructions: Instructions are supplied in this manual and contain all appropriate information for your building model.
PLAN AHEAD.... A3 Watch the Weather: Be sure the day you select to install your building is dry and calm. Do not attempt to assemble your building on a windy day. Be careful on wet or muddy ground. Teamwork: Whenever possible, two or more people should work together to assemble your building. One person can position parts or panels while the other is able to handle the fasteners and the tools.
SAFETY FIRST.... A4 Safety precautions are important to follow throughout the construction of your building. •Care must be taken when handling various pieces of your building since some contain sharp edges. Please wear work gloves, eye protection and long sleeves when assembling or performing any maintenance on your building. •Practice caution with the tools being used in the assembly of this building. Be familiar with the operation of all power tools.
CARE & MAINTENANCE.... A5 Web Finish: For long lasting finish, periodically clean and wax the exterior surface. Touchup scratches as soon as you notice them on your unit. Immediately clean the area with a wire brush; wash it and apply touch-up paint per manufacturer's recommendation. Roof: Keep roof clear of leaves and snow with long handled, soft-bristled broom. Heavy amounts of snow on roof can damage building making it unsafe to enter.
ACCESSORIES.... A6 WEB ROOF STRENGTHENING (heavy snow load) KITS FLOOR FRAME KITS Extra roof beams and gable braces designed for added protection against heavy snow accumulation. Increases the strength of your roof by 50%. ANCHOR KITS Model No. AK4 Anchor Kit contains heavy-duty steel augers, 60' (18m) of steel cable and 4 cable clamps. No digging or concrete pouring, just insert cable under roof, over roof beams, into augers and twist augers into the ground.
THIS PAGE WAS LEFT BLANK INTENTIONALLY 7
THIS PAGE WAS LEFT BLANK INTENTIONALLY 8
Foundation C09 The Foundation For Your Building OPTION 1: ARROW FLOOR FRAME KIT: (Order No. FB5465) Arrow has the best base for your building in this simple kit. It keeps stored items above the ground. This kit should be used with one of the following: A. To support a plywood deck B. To be filled with sand. We recommend the combined use of 1. an ARROW FLOOR FRAME KIT and 2. an ARROW ANCHORING KIT as an effective method of securing the building to the ground. Allow 1 - 2 hours for construction.
Anchoring A10 Anchoring Down The Building It is important that the entire floor frame be anchored after the building is erected. Below are recommended ways of anchoring. Arrow Anchoring Kit: (Model No. AK4 or 60298) Recommended for use with any suggested base. Contains: 4 Anchors with Cable, Clamps and installation instruction. Anchoring into Wood/Post: Use 1/4" Wood Screws. There are 1/4" (0,63cm) dia. holes provided in the frames for proper anchoring. 1. 2.
Hardware C11 Remove from bag of screws and save for the last step 65103 #8-32 Hex Nut (61) 65900A #10Bx1/2" Black Screw (8) (Packed with Screws) 65923 #8-32x3/8" Bolt (61) 65004 #8Ax5/16" Screw (176) 66045 Handle (2) 66646 Washer (181) (5 sheets of 40) 65109 #8-32 Acorn Nut (6) (Packed with Screws) 67468 Peak Cap (2) (Arrow Logo) 66769 Door Slide (4) 66382 Lower Door Guide (4) 66183 Roof Trim Cap (2 right & 2 left) 67293 Weather Stripping (1) 66029 Plug (2) (Packed with Screws) 11
Parts List C12 Assembly Key No.
Assembly by Key No.
● Parts Needed For ● Step 1 ● 9396 Door Track (1) Door Track Assembly C14 The door track assembly supports the sliding doors and reinforces the front wall. Hint: The holes in the top side of the door track are for fastening the gable to the top of the front wall in a later step. 66769 1 Position door slides onto the legs, Long Leg on Top from the end of door track, as shown in the end view. 9396 Short Leg on Bottom STEP 1 66769 END VIEW 2 Set this piece aside for later use.
Step 2 ● Parts Needed For ● Floor Frame ● 9403 Front Floor Frame (1) ● 9399 Rear Floor Frame (1) ● 9402 Side Floor Frame (2) C15 RIGHT REAR 9402 1 Assemble the four corners of the floor frame using two screws at each corner as shown. At the front corners fasten bolts through from the bottom with nuts on top. 9399 9402 9399 STEP 1 9402 FR ON T RIGHT FRONT 9402 9403 9403 2 Measure the floor frame diagonally. When the diagonal measurements are equal, the floor frame is square.
Step 3 ● 9388 Front Corner Panel (2) ● 9392 Rear Corner Panel (2) ● 9364 Wall Panel (2) ● Parts Needed For ● Corners/Wall Panels C16 NOTE The remainder of the building assembly requires many hours and more than one person. Do not continue beyond this point if you do not have enough time to complete the assembly today. A partially assembled building can be severely damaged by light winds. 9392 WideSide STEP REAR 2 Each screw and bolt in the wall requires a washer.
Step 4 ● 9397 Rear Wall Angle (1) ● 9925 Rear Wall Channel (1) ● 9926 Side Wall Channel (2) ● 9400 Side Wall Angle (2) ● Door Track Assembly (1) ● Parts Needed For ● Frames C17 The main frame pieces give rigidity to the side walls and provide a surface for attaching the gables which support the roof. 1 Fasten the rear wall angle across the inside top of the rear wall using screws. 2 Fasten the rear wall channel across the middle of the rear wall using screws.
● Parts Needed For ● Step 5 ● 8995 Wall Panel (2) Wall Panels C18 1 Fasten the wall panels at the top and bottom with screws. Crimped Rib Underneath 2 Fasten the center of each panel to the wall channel with screws. Fasten overlapping ribs as before.
Step 6 ● Parts Needed For ● ● 9900 Door Jamb (2) Door Jamb C19 The door jambs reinforce the door opening and provide an attractive trim. Follow these steps for both door jambs. STEP 1 (3) bolts TOP VIEW Door Track 1 Fasten a door jamb to the front panel with three bolts, nuts and acorn nuts, as shown. Push a plug into hole at center of jamb, closest to door opening. Hex Nut Acorn Nut Plug 9900 Bolt Plug 9900 2 Fasten the top of the door jamb to the door track with two screws.
Step 7 ● 5996 Right Gable (2) ● 5997 Left Gable (2) ● 6658 Gable Brace (2) ● Parts Needed For ● Gables/Braces C20 The gables go on top of the front and rear walls to support the roof beam. NOTE The gables are packed nested together and might be mistaken as one piece. Carefully separate them before continuing. STEP 1 Gable 6658 Gable Brace 1 Lift and fasten a right and left gable, under angle at corner, to the door track with screws.
Step 8 ● Parts Needed For ● ● 5964 Roof Beam (1) ● 5982 Roof Angle (1) Roof Beam/Angle C21 1 Fasten the roof beam, small holes on top, to the gable brace of the front gable. STEP 3 2 Fasten the other end of the roof beam to the gable brace of the rear gable. Roof Angle 3 Fasten the roof angle to the roof beam as shown using screws.
Step 9 ● Parts Needed For ● ● 6442 Right Roof Panel (1) Right Roof Panel C22 Installing the roof panels is best done with a step ladder. Begin installing roof panels at the back right corner of the building. Each screw and bolt in the roof requires a washer. STEP 1 NOTE Measure the building diagonally again and make adjustments to make sure the building is square and level. This will make the roof panels fit better, and holes will align.
Step 10 ● Parts Needed For ● Left Roof Panel ● 6443 Left Roof Panel (1) C23 1 Install a left roof panel 6443 at the left rear corner of the roof.
● Parts Needed For ● Step 11 Front of Roof ● 6443 Left Roof Panel (1) ● 6442 Right Roof Panel (1) C24 1 Cover the joint at the peak with weather stripping tape. Unroll the tape and press it down over the opening at the ridge as you install each roof panel. Do not cut the tape at this time. 2 Install a left and right roof panel in the sequence and positions shown in Step 9. Follow fastener sequence and instructions in Steps 9 thru 11 while fastening roof panels.
● Parts Needed For ● Step 12 Ridge Cap/Roof Trim ● 6869 Ridge Cap (1) ● 6015 Side Roof Trim (2) C25 1 Install the ridge cap on the com- STEP pleted roof section using bolts and nuts. 1 Peak Cap 6869 STEP 2 Fasten the roof panel ribs, peak cap and ridge cap together using bolts and nuts. Fasten the remaining peak cap in the same manner.
Step 13 ● 6657 Door Handle Brace (2) ● 10487 Right and Left Doors (2) ● 10499 Horizontal Door Brace (4) ● Parts Needed For ● Door Assembly C26 The steps on this page tell how to assemble the right door. You will perform exactly the same procedures for the left door. Each screw and bolt in the door requires a washer. Proceed as follows: 10499 66045 6657 66045 6657 1 Attach the door handle brace and handle to the door with 1 bolt as 66382 shown. Don't tighten the bolt yet.
Step 14 ● Parts Needed For ● Door Installation & Adjustment ● Right Door Assembly (1) ● Left Door Assembly (1) C27 Horizontal Door Brace Gable Door Track Door Slide 1 Door From inside the building, put the bottom of the right door assembly (on your left when you are inside the building) behind door jamb into the front frame track. STEP STEP 1 2 2 Position the top of the door so that that holes in the door line up with the holes in the door slides.
C28 EN65-A HM65S ENB65 NW65 SOME FACTS ABOUT RUST Rusting is a natural oxidizing process that occurs when bare metal is exposed to moisture. Problem areas include screw holes, unfinished edges, or where scrapes and nicks occur in the protective coating through normal assembly, handling and use. Identifying these natural rusting problem areas and taking some simple rust protection precautions can help to stop rust from developing, or stop it quickly as soon as it appears. HM65-A SA65-A 1.