Volition TM Network Solutions TM VOL-N100VF+TX TM VF-45 + RJ-45 Wake On LAN Fast Ethernet Adapter User Guide
Table of Contents Introduction Package Checklist Hardware Description LED Functions Installing the Hardware NIC Driver Installation and Configuration Windows 98 A. Installing the driver B. Changing the media type Windows Millennium A. Installing the driver B. Changing the media type Windows 2000 A. Installing the driver B.
Introduction The 3M VOL-N100VF+TX WOL PCI 100Mbps NIC is a dual-port and dual-speed Fast Ethernet card for PCI local bus compliant computers. This plug-n-play device is auto-configurable upon power up. The RJ-45 port supports NWAY Auto Negotiation to automatically select the optimum speed and communication mode of an attached device. The VOL-N100VF+TX WOL NIC is capable of advanced Wake On LAN functions. It is also PCI 2.2 compliant and complies with the WfM 2.0 standard.
VOL-N100VF+TX VF-45TM Activity Link 100/10 Mbps Full Duplex/Collision RJ-45 LED Functions The following table describes the operation of the VOL-N100VF+TX PCI 100Mbps NIC status LEDs: LED Status Description LNK Solid Green Indicates a valid network connection. Off Indicates no valid network connection. Flashing Amber Indicates incoming and outgoing network traffic. Off Indicates that there is no network traffic.
4. a) Connecting to the RJ-45 Port. Connect the VOL-N100VF+TX PCI 100Mbps NIC directly to a 10BASE-T or 100BASE-TX hub or switch using UTP cable (Category 3, 4, 5e or 5 for 10BASE-T; Category 5e/5 for 100BASE-TX). The maximum allowable length of UTP cable connections is 100 meters (328 ft). This connection can be made directly to the device, or indirectly via a wall outlet that has the proper wiring for an RJ-45 connector.
VOL-N100VF+TX 1. Right click on the “Network Neighborhood” icon on your Desktop. 2. Select “Properties” from the drop-down menu. 3. Click on the listed adapter “3M VOL-N100VF+TX PCI 100Mbps NIC.” 4. Click on the “Properties” button. 5. Click on the “Advanced” tab. 6. The “Media Type” selector is the first configurable option in the list.
. After selecting the desired “Media Type”, click “OK” to close the current window. 8. Close the “Network” window by clicking “OK.” 9. Reboot your PC when prompted to do so. Note: The media type change will not take effect until the PC is rebooted. Windows 2000 A. Installing the driver: 1. Upon boot-up, the “Found New Hardware Wizard” window will appear. 2. Insert 3M Driver CD-ROM into the PC’s CD-ROM drive and click “Next.” 3. Select “Search for a suitable driver for my device”, then click “Next.” 4.
VOL-N100VF+TX Remote LAN Wakeup Remote LAN Wakeup capability is a key feature of a centrally managed PC environment. This technology enables networked PCs to be “woken up” from a sleep or powered-off state so they can be managed from a central location, at any time of the day or night. To employ Remote LAN Wakeup, three elements are required: • Desktop management software that can send a “wake-up” frame to a PC.
Using 3M NIC Diagnostics The 3M Diagnostics program, “DIAG.EXE”, is a MS-DOS program that verifies the basic functions and components of the 3M VOL-N100VF+TX PCI 100Mbps NIC. This program can be found in the “\DIAGS” subdirectory of the 3M Driver CD-ROM. It is highly recommended that this useful program be run before placing a call into the 3M Helpdesk.
VOL-N100VF+TX Instructions for Running the “Network Test” • The Network Test requires a minimum of two (2) PCs in order to both send and receive data. • Press to start the test on two (2) PC’s installed with 3M VOL-N100VF+TX NICs • Once the test has begun, the following statistics can be observed on the screen: • Frames transmitted • Frames received • Transmit Throughput • Receive Throughput • Collisions • Allignment errors • Press again to stop the Network Test.
Known Resolutions for Common Problems The troubleshooting section below shows solutions for three well known Problem Symptoms that can be associated with a network interface card: 1. No link 2. Have link, but no usable network connection 3. Have link AND a usable network connection, but there is poor network performance Note: The Link LED on should not be lit when there is no link Possible causes of a “No Link” problem… Solutions… 1.
VOL-N100VF+TX Possible causes of a “No Link” problem… Solutions… 5. There might be a problem with the network cabling. • View the Link LED. • The Link LED will be solid green if the NIC is currently linked to another network device. • Run the 3M NIC Diagnostics • Monitor the test results for the: Link Test • If this test FAILs, first ensure that you have selected the proper Media Type. Chose the “Auto Select” media type if in doubt of what media type to select.
Note: The Link LED on the NIC should be lit green when there is link. Possible causes of a “Link, but no Solutions… usable network connection” problem... 1. The NIC drivers may not be properly installed. Note: There will be “Link, but no usable network connection” only when the Link LED is lit and the Link test is a PASS. • First ensure that the operating system you are using Windows 98/ ME/2000. • Install the NIC drivers per the installation instructions of this User Guide. • Run the 3M NIC Diagnostics.
VOL-N100VF+TX Recommendations Recommendation Reason for the Recommendation If multiple NICs are needed in the same PC, multiple VOL-N100VF+TX NICs should be used This will rule out the possibility of a NIC compatibility problem existing between different types of NICs. EMI Certification FCC Class B Certification This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1. This device may not cause harmful interference, and 2.
Specifications Network Interface 10BASE-T RJ-45 (UTP cable; Categories 3, 4, 5e or 5) 100BASE-TX RJ-45 (UTP cable; Category 5e/5) 100BASE-FX VF-45TM (62.5/125 or 50/125 micron multimode fiber cable) Bus Interface 32-bit PCI Bus Master PCI Interrupt Channel INTA LED Indicators Link, Activity, Speed, Duplex/Collision Size 121.5 x 120 mm (4.8 x 4.7 in.) Weight 66 g (2.3 oz) Operating Voltage 3.
3M, Volition, VF-45TM, and the “dot wave” symbol are trademarks of 3M Important Notice Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Warranty; Limited Remedy; Limited Liability This product will be free from defects in material and manufacture for a period of one year from the date of purchase.
