Outdoor Storage User Manual

ManualsBrandsArrow Storage Products ManualsOutdoor StorageArrow Storage Building

The rear floor frame is made up of 2

pieces. The holes in these pieces

will align when the pieces are posi-

tioned with correct amount of over-

lap. The illustration below shows the

proper overall length for the rear.

1 1

1 Overlap

rightright

right and

left rear framesleft rear frames

left rear frames,

align holes, and fasten using 8 bolts

and nuts. Make 3 assemblies. Use 1

assembly for this step.

2 2

2 Position

floor frames floor frames

floor frames as shown

and fasten at each corner using 2

bolts through the bottom and nuts on

top. When installing

side frame 7914side frame 7914

side frame 7914,

be sure set of holes 1" in from end of

frames are installed toward rear of

building.

3 3

3 Fasten side frames together with a

truss supporttruss support

truss support using 4 bolts through

the bottom and nuts on top.

Step 5Step 5

Step 5

BW18

● Parts Needed For ●

Floor FFloor F

Floor F

ame ame

ame

AssembAssemb

Assemb

12x17, 12x24, 12x3112x17, 12x24, 12x31

12x17, 12x24, 12x31

●●

●

8532 Right Rear Frame (1) 8532 Right Rear Frame (1)

8532 Right Rear Frame (1)

●●

●

8531 Left Rear Frame (1) 8531 Left Rear Frame (1)

8531 Left Rear Frame (1)

●●

●

7914 Side Frame (see below) 7914 Side Frame (see below)

7914 Side Frame (see below)

●●

●

7857 Truss Support (see below) 7857 Truss Support (see below)

7857 Truss Support (see below)

#10-32 Square Nut

#10-32x7/16" Bolt

IF YOU ARE BUILDING A 12x24

Fasten additional side frame 7914 and truss

support 7857 to side frame 7914 using the

side connection. Position rear frame at rear

of assembly and fasten using the rear

corner connection.

IF YOU ARE BUILDING A 12x31

Fasten 2 additional side frames 7914 and

truss supports 7857 to side frame 7914

using the side connection. Positon rear

frame at rear of assembly and fasten using

the rear corner connection.

4 4

4 Measure the floor frame diago-

nally. When the measurements

are equal, the floor frame is square.

5 5

5 Select location of side door on

either side, toward the rear of build-

ing. Install

lower door tracklower door track

lower door track and

rampramp

ramp, notch toward outside, using

1/4" bolts and nuts. See Step 12 for

Rear Door Installation.

7834

Position with small holes

toward outside of building

FRONTFRONT

FRONT

#10-32x1/4" Bolt

STEP

NOTENOTE

NOTE

Do not fasten the floor frames to

your foundation at this time.

You will anchor the building

after it is erected.

The floor frame The floor frame

The floor frame

must be squaremust be square

must be square

and level and level

and level

or holes will not align.or holes will not align.

or holes will not align.

●●

●

7837 Side Frame (2) 7837 Side Frame (2)

7837 Side Frame (2)

●●

●

7834 Right Front Frame (1) 7834 Right Front Frame (1)

7834 Right Front Frame (1)

●●

●

7835 Left Front Frame (1) 7835 Left Front Frame (1)

7835 Left Front Frame (1)

●●

●

7517 Lower Door Track (1) 7517 Lower Door Track (1)

7517 Lower Door Track (1)

●●

●

7560 Ramp (1) 7560 Ramp (1)

7560 Ramp (1)

7837

7857

7517

7835

7837

7914

7857

7837

7914

STEP

Rear Frame 140 7/8"

3,6m

Slot

Notch toward outside

of building

8531

8532

8531

8532

Level

7560

7914

7560

Side Frame

7517

SIDE

REAR

7857

NOTENOTE

NOTE

Position of holes, and fasten at

the 1st set of holes. See side

connection.

STEP

Level