Outdoor Storage User Manual

The rear floor frame is made up of 2
pieces. The holes in these pieces
will align when the pieces are posi-
tioned with correct amount of over-
lap. The illustration below shows the
proper overall length for the rear.
1 1
1 1
1 Overlap
right right
right right
right and
left rear framesleft rear frames
left rear framesleft rear frames
left rear frames,
align holes, and fasten using 8 bolts
and nuts. Make 3 assemblies. Use 1
assembly for this step.
Step 4Step 4
Step 4Step 4
Step 4
BW17
● Parts Needed For ●
Floor FFloor F
Floor FFloor F
Floor F
rr
rr
r
ame ame
ame ame
ame
AssembAssemb
AssembAssemb
Assemb
ll
ll
l
y 12x10y 12x10
y 12x10y 12x10
y 12x10
●●
●●
●
8532 Right Rear Frame (1) 8532 Right Rear Frame (1)
8532 Right Rear Frame (1) 8532 Right Rear Frame (1)
8532 Right Rear Frame (1)
●●
●●
●
8531 Left Rear Frame (1) 8531 Left Rear Frame (1)
8531 Left Rear Frame (1) 8531 Left Rear Frame (1)
8531 Left Rear Frame (1)
●●
●●
●
7837 Side Frame (2) 7837 Side Frame (2)
7837 Side Frame (2) 7837 Side Frame (2)
7837 Side Frame (2)
●●
●●
●
7834 Right Front Frame (1) 7834 Right Front Frame (1)
7834 Right Front Frame (1) 7834 Right Front Frame (1)
7834 Right Front Frame (1)
●●
●●
●
7835 Left Front Frame (1) 7835 Left Front Frame (1)
7835 Left Front Frame (1) 7835 Left Front Frame (1)
7835 Left Front Frame (1)
●●
●●
●
7517 Lower Door Track (1) 7517 Lower Door Track (1)
7517 Lower Door Track (1) 7517 Lower Door Track (1)
7517 Lower Door Track (1)
●●
●●
●
7560 Ramp (1) 7560 Ramp (1)
7560 Ramp (1) 7560 Ramp (1)
7560 Ramp (1)
17
#10-32 Square Nut
#10-32x1/4" Bolt
7837
8531
4 4
4 4
4 Select location of side door on
either side, toward the rear of build-
ing. Install
lower door tracklower door track
lower door tracklower door track
lower door track and
rampramp
rampramp
ramp, notch toward outside, using
1/4" bolts and nuts, as shown. See
Step 12 for Rear Door Installation.
2 2
2 2
2 Position
floor frames floor frames
floor frames floor frames
floor frames as shown
and fasten at each corner using 2
bolts through the bottom and nuts
on top.
3 3
3 3
3 Measure the floor frame diago-
nally. When the diagonal mea-
surements are equal, the floor frame
is square.
7834
Position with small holes
toward outside of building
7835
FRONTFRONT
FRONTFRONT
FRONT
7837
7517
7560
8532
Level
#10-32x7/16" Bolt
SIDE
REAR
Slot
Notch toward outside
of building
Side Frame
7517
7560
8531
Rear Frame 140 7/8" 3,6m
8532
STEP
11
11
1
STEP
44
44
4
STEP
33
33
3
STEP
22
22
2
NOTENOTE
NOTENOTE
NOTE
Do not fasten the floor frames to
your foundation at this time. You
will anchor the building after it is
erected.
The floor frame The floor frame
The floor frame The floor frame
The floor frame
must be squaremust be square
must be squaremust be square
must be square
and level and level
and level and level
and level
or holes will not align.or holes will not align.
or holes will not align.or holes will not align.
or holes will not align.