Instructions

Operation
Set description
Initial Service
To set/replace batteries:
1. Unscrew the tailcap.
2. Place the batteries with the positive contact (+) facing the head of the flashlight.
3. Adjust the tailcap and tighten it as far as it can go.
The flashlight is ready for operation.
1. 2.
3.
We DO NOT RECOMMEND to leave power sources inside the flashlight for a long storage period, as batteries (especially, non-rechargeable) can
leak for various reasons and damage the inner parts of the flashlight. If you want to keep your flashlight in a stand-by state with batteries in then
use new and high-quality batteries and store the flashlight in acceptable for batteries operational temperature and revise the batteries' state at
least once a month. If you have noticed any signs of batteries' defects then withdraw them from the flashlight and utilize. It is also recommended
to replace discharged batteries with new ones before the storage as the chance of leakage is higher with discharged batteries.
ь Your flashlight can inconsiderably differ from the pictures in the manual.
ь The producer reserves the right to change the package at his own discretion without modifying this manual.
Items included in the package:
1 - Flashlight
2 - Holster
3 - Clip
4 - 2 spare O-rings
5 - 18650 Li-Ion battery (for Prime C2 Pro Magnet USB)
18350 Li-Ion battery (for Prime C1 Pro Magnet USB)
6 - Magnet USB charger
7 - User manual
3
x2
4 765
2
How to turn on a magnet charger:
Unscrew the tailcap for 1/4 of a circle and turn on a magnet
charger device to the tailcap.
Approximate time for charging a fully discharged battery is 6-8
hours. We recommend using adapters with 1A and higher.
Charger device battery indication:
1. Red color – the charging is going on.
2. Green color – the charging is finished.
3. Red color blinking – unscrew the tailcap for 1/4 for
charging.
Prime Magnet USB
1
1/4
Main
Press & Hold
Click x2
Main вFirefly
в
Any Mode
Main
Click x2
Press & Hold
Firefly
Firefly
гд
Main
Turbo1
гд
Turbo2
OFF вFirefly1
Firefly1 вFirefly2
ез
Firefly3
Press & Hold
Turbo
Click x3
вTurbo
Any Mode
Any Mode
Strobe
Press & Hold
Click x4
вStrobe
Press & Hold
1
2
+
5sec
< 100%
< 75%
Battery level
Switching State Indication
ON / OFF
Strobe1 в Strobe2
ез
Strobe3
Main1 вMain2
ез
Main3
1sec
Low Battery Indication
Warning
Critical
< 25% < 10%
2sec
The flashlight has 4 Sections of modes:
[Section 1] – Firefly modes [Section 3] – Turbo modes
[Section 2] – Main modes [Section 4] – Special modes
In OFF state:
Click: To turn on the last used mode.
Press and hold: To turn on Firefly1 mode in [Section 1].
In ON state:
Click: To turn off the flashlight.
Press and hold: To start cycling through the modes of actual Section.
The same in OFF & ON states:
2 clicks: To turn on the Main mode [Section 2]. Then double clicks will
switch modes between chosen modes in [Section 1] and [Section 2].
3 clicks: To turn on Turbo mode [Section 3].
4 clicks: To turn on Strobe mode [Section 4].
Flashlight has 2 types of operation:
1. General. The flashlight is switched on/off by 1 click.
2. Tactical. The flashlight will switch on in the last used mode only for
the time the button is being pressed. This type of operation is useful
for short-time lighting and setting signals.
To access the Tactical operation type, unscrew the tailcap to 1/4, press
the button and tighten the tailcap again keeping the button pressed.
To return to the General type – press the button and while keeping it
pressed – unscrew the tailcap to 1/4.
Automemorizing. After switching off the last used Mode is memorized
for quick 1-click access at next switching on.
Lock-out function. Unscrew the tailcap to 1/4 for the protection from
accidental switching on. State Indication will be turned off.
Multicolor State Indication. Shows the battery level by short flashes
every 5 seconds.
Switching Multicolor State Indication ON/OFF. It is switched off by
default in OFF-state and Firefly modes. To turn on and off: unscrew the
tailcap to 1/4, press the button and holding the button pressed –
tighten the tailcap and then unscrew it again. The settings will be
memorized even when battery is changed. Ultra-low current
consumption allows color indication to work for more than 25 years.
Warning indication shows the battery level and the temperature inside the flashlight.
Low battery level. When it is < 25%, the color LED will show the warning level – flashing in orange color once in 2 second. With a further
voltage reducing brightness will start to decrease in steps for safety of the battery and user. If brightness will be <25% from nominal
value, the main LED will flash 2 times. Critical battery level <10% is red indicated once a second.
High temperature. When it increases to the warning level – the color LED flashes by orange 3 times once in 2 seconds. At critical level –
it flashes by red 3 times once in 1 second, brightness starts to reduce. After cooling down the brightness increases to usual level.
Constant light. Powerful electronics provide constant brightness even in the Turbo1 mode, using all energy of the battery. And the
Turbo2 mode gives the maximum brightness as the Overboost technology in cars, but until temperature of a flashlight and a discharge
current of the battery don't exceed critical values.
Digital Light Stabilization & Safe Soft-Start System monitors battery voltage, starts the flashlight at an admissible brightness or
decreases it by steps when the voltage dramatically fall down. These actions increase runtime, use all available energy, get longer
lifetime of rechargeable battery and protect it from overdischarge or overheating.
Active temperature control. The flashlight can heat up in Turbo mode quickly. When the temperature become +60°C – the brightness
decreases by small steps. After cooling-down (provided that battery voltage is sufficient) the brightness increases to the Turbo mode
again. This stepping goes cyclically to maintain the user's safety and the flashlight's functionality. In conditions of good air-cooling the
flashlight delivers light without stepping down even in Turbo mode. There are no preset timers for stepping, but real-time active
temperature measurements.
2sec
High Temperature Indication
Warning
Critical
WARM
HOT
1sec