Instructions / Assembly

ManualsBrandsArmstrong CEILINGS ManualsBuilding materialsCountry Classic 6 in. x 48 in. Surface-Mount Tongue and Groove Acoustic Ceiling Plank (960 sq. ft. / Pallet)

BEFORE YOU BEGIN:

• Mineral fiber planks should be handled with care, especially when removing them from the carton and during the

installation process. The edges and face of the planks can damage easily.

• Store and install ceilings in areas with a temperature range of 60° to 85° F and not more than 70% relative humidity.

• Remove ceiling planks from cartons 24 hours before installation and allow to adjust to normal interior conditions of the

installation area.

• Do not apply loose fill or bat insulation so that it rests directly on the back of the planks.

• Do not install ceiling tiles below embedded radiant-heat coils.

• Keep hands clean during tile installation to avoid fingerprints and smudges.

• Handle ceiling planks carefully to protect the face and edges from damage.

• Always cut ceiling tiles face up with a sharp utility knife.

• If you are installing on a sloped ceiling, the Easy Up

Installation System is intended for ceilings with a slope of less

than 10 degrees. Planks should run horizontally across the plane of the ceiling. Planks should not run vertically, with

the long edge running up the slope of the ceiling.

• For Adhesive Applications of mineral fiber only planks directly to existing drywall or plaster ceilings: Ceiling tile

adhesive recommended, such as Henry 237 AcoustiGum

™

Acoustical Ceiling Tile Adhesive. Please follow adhesive

manufacturer’s instructions for application and usage. Armstrong does not guarantee the performance of this or

other adhesive products, either alone or in conjunction with Armstrong

products.

SAFETY TIPS:

• Establish and maintain adequate ventilation in the work area. If high dust levels are anticipated during installation,

such as with the use of power tools, take proper precautions.

• Wear long-sleeve, loose fiting clothing and gloves.

• Wear safety glasses to minimize the risk of eye injury.

• Use a sharp utility knife to ensure clean cuts. When not in use, store properly.

MAINTENANCE HINTS:

• Remove dust and loose dirt with a sot brush or vacuum hose with a sot brush atachment.

• Remove pencil marks, small smudges, or clinging dirt with an ordinary art-gum eraser.

• Clean with a damp sponge, mild soap and lukewarm water if necessary. Do not soak tiles with water.

TOOLS NEEDED TO INSTALL YOUR CEILING

How to install your Mineral Fiber Planks

using the Easy Up

Installation System

or Adhesive

French

Spanish

Gafas de

seguridad

Cinta métrica

Regla

Lápiz

Cuchilla

multiuso

Cordel

Martillo

Localizador

de montantes

Segueta

Mascarilla contra

polvo

Taladro/Pistola

para tornillos

Guantes

Cordel

con tiza

Tijeras para

metales

Tornillo de rosca

gruesa no. 6 para

paneles de yeso

Nivel de carpintero

de 4 pies (1,2 m)

Destornillador

Lunettes

de sécurité

Règle à tracer

Marteau

Crayon

Couteau

tout usage

Ficelle

Ruban

à mesurer

Tournevis

Scie à métaux

Perceuse/Visseuse

Gants

Cordeau

à tracer

Cisaille

à métal

Vis pour gypse

à gros f ilet n° 6

Niveau à bulle

de 4 pi

Localisateur

de montant

Masque

antipoussières

Safety

Glasses

Straight Edge

Hammer

Pencil

Utility

Knife

String

Ta pe Measure

Screw Driver

Hacksaw

Drill/ Screw Gun

Gloves

Chalk

Line

Tin

Snips

#6 Course Thread

Drywall Screws

4' Carpenter’s

Level

Stud Finder

Dust mask

Summary of content (4 pages)

PAGE 1
How to install your Mineral Fiber Planks using the Easy Up® Installation System or Adhesive BEFORE YOU BEGIN: • Mineral fiber planks should be handled with care, especially when removing them from the carton and during the installation process. The edges and face of the planks can damage easily. • Store and install ceilings in areas with a temperature range of 60° to 85° F and not more than 70% relative humidity.
PAGE 2
How to install your Mineral Fiber Planks using the Easy Up® Installation System or Adhesive BEGIN INSTALLATION Locate ceiling joists To locate hidden joists, use either a stud finder or tap on the ceiling until you hear a solid thud. Mark the joist locations with chalk lines. Repeat this to locate other joists and determine their direction. Generally, joists are spaced 16" or 24" on center. Determine border tile size for a balanced appearance Example 1.
PAGE 3
How to install your Mineral Fiber Planks using the Easy Up® Installation System or Adhesive Snap a Chalk Line • Add 1/2" to your border plank width and snap a chalk line across the tracks at that distance from front wall. Cut First Row of Border Planks • Familiarize yourself with the plank edges and face before you begin cutting your first plank. (illus. D) • Trim first plank to the calculated border plank width, face up with a sharp utility knife. Do not cut off flange sides of plank.
PAGE 4
How to install your Mineral Fiber Planks using the Easy Up® Installation System or Adhesive STEP 3: INSTALL WALL MOLDING • Paint or stain decorative molding before installing. • Install molding at the joint between the ceiling and walls. • Nail molding into the wall studs at least every 24". (illus. H) illus. H NOTE: All Armstrong® mineral fiber ceiling tiles can be painted with latex paint. The front and back of the tile should be painted.