User's Manual

CLEANING THE RIFLE:
Before cleaning your rifle, be certain it is completely unloaded. Clear the action several times to be sure no cartridge remains in the chamber.
With normal use, it is not necessary to clean the bore of your rifle. However, if your rifle gets wet, or if any foreign material gets into the action, barrel cleaning as
described below is recommended.,
To clean the bore of the barrel, use a cleaning rod and patch. Clean the barrel with powder solvent, then wipe it dry, wipe lightly with gun oil after cleaning.
09 | MAINTENANCE
In cleaning the action, the steps listed below should be followed carefully to assure proper
disassembly, cleaning and reassembly.
1. Remove magazine from the rifle.
2. Unscrew magazine cover housing hold down screw
(1677 and AK018A) and remove magazine box cover
housing from the rifle. 3. Unscrew pistol grip screw
(AK022A) and remove pistol grip and trigger guard from
the rifle.
4. Remove rod placed under the barrel. The rod can be
removed by rotating it counterclockwise and pushing it
inward (toward the lower handguard) and then lifting up
knurled end first, pull it away from the handguard.
5. Loosen the gas tube front retainer set screw (1605)
and slide the retainer forward. Then pull out the gas tube
(dummy) (AK003) from its recess in the rear sight base.
6. Loosen the lower handguard front cover retainer tube
set screw. Slide forward the retainer tube and front
cover and you now remove the lower handguard away
from the rifle.
7. Unscrew the lower butt pad retainer screw (for
standard model only).
8. With the use of extra long and heavy duty nutdriver,
swing out the butt pad and insert the nutdriver into the
hole of the buttstock and loosen the nut of stockbolt.
(AK021A) which is inside the buttstock (for standard
model only).
9. Now you can separate the buttstock from the rifle (for
standard model only).
10. Loosen out the four screws in the receiver cover
right side. Then separate the left side receiver cover
from the rifle assembly together with the right side
receiver cover.
FURTHER DISASSEMBLY OF THE ACTION AND OF THE SIGHT (FRONT & REAR)
ARE NOT RECOMMENDED AND SHOULD ONLY BE ATTEMPTED BY A
COMPETENT GUNSMITH OR AUTHORIZED SERVICE CENTER.
CAUTION:
SHOULD BE EXCERCISED IN REATTACHING THE RECEIVER CAP. YOU HAVE TO
COMPRESS THE SPRINGS GENTLY AND FIRMLY TO ACOID BUCKLING OR KINKING
OF SPRINGS, LET THE THREADS OF RECEIVER CAP TOUCHES THE THREAD OF THE
RECEIVER AND ROTATE THE CAP CLOCKWISE TO TIGHTEN. TO REASSEMBLE THE
OTHER PARTS, FOLLOW THE STEPS STATED ABOVE FROM NO. 14 IN THE REVERSE
ORDER.
CAUTION:
11. Now, separate rifle assembly from the (right side)
receiver cover by lifting the rifle up and away (muzzle
end first) from the receiver cover.
12. Punch out trigger stop pin (1648) and trigger pin
(1647).
13. Unscrew the two hold down screws of trigger
housing (1658 & AK1657). The trigger housing assembly
can now be separated from the receiver-barrel
assembly. Carefully take note of the trigger spring and
follower located at the rear end of trigger housing.
14. Unscrew receiver cap lock screw (1618).
15. Loosen out the receiver cap. Be careful in removing
receiver cap as it is under pressure by compressed
spring inside.
16. The spring assembly and the bolt assembly can now
be removed from the receiver. Keep the part in the
same order you have taken them out of the receiver to
avoid confusion in reassembly.
17. The barrel, receiver and action are now ready for
thorough cleaning. The action should be cleaned in
solvent (or any equivalent cleaning oil), dried and oiled
lightly prior to reassembly.
18. To reassemble, insert the bolt and firing pin (bolt face
end first) into the receiver, then followed by the spring
assembly unit. Then insert firing pin spring / spring guide
into the boltrear center hole, insert recoil spring guide
sleeve, recoil spring and recoil spring retainer sleeve (in
that order) and finally, the receiver cap.
SEE FULL VIDEO TUTORIALS ON OUR
WEBSITE
SCAN QR