WWW.WARSENSOR.COM WARSENSOR WSF Manual ARMOTECH and WARSENSOR are trademarks owned by AI-MOK Paintball Ltd.; All ARMOTECH and WARSENSOR products are manufactured by ARMOTECH Taiwan Co., Ltd. only. © 2004 - 2005 AI-MOK Paintball Ltd. All rights reserved 1 WARSENSOR WSF User Manual Revision 1 printed Mail: info@warsensor.
WWW.WARSENSOR.COM Safety First! WARNING WARSENSOR PAINTBALL MARKERS ARE NOT A TOY. ANY MISUSE MAY CAUSE SERIOUS INJURY OR DEATH. THE USER AND ANY PERSON WITHIN RANGE MUST WEAR EYE PROTECTION DESIGNED FOR PAINTBALL USE. READ THIS OWNERS’S MANUAL COMPLETELY BEFORE LOADING, PRESSURIZING, OR OPERATING YOUR WARSENSOR PAINTBALL MARKER.
WWW.WARSENSOR.COM • Never shoot at domestic animals or wildlife • Never mark objects outside the confines of the game or authorized shooting areas • Never look down the barrel of a marker • Before disassembly, storage, or transport of this marker, remove ALL paintballs from the marker, barrel, and loader: remove power source: and remove all gas or air from the power system.
WWW.WARSENSOR.COM Introduction to the WSF Your Package should Include the Following: Features: Package Contents: - Rear snap cocking system -Tactical Style -Vertical Power Feed -R.I.S. Handle -Delrin Bolt -4 Sides Sight Rail -Matte Finish Hard Anodizing -12” Aluminum, Micro-Honed Barrel -Velocity Adjuster -Aluminum Double Trigger Frame -Rubber Contoured Grip -Quick Strip Pin -Bottom-Line Set Up -Operates on HPA, N2 or CO2 -Warsensor Field Marker -Vertical Feed System -R.I.S.
WWW.WARSENSOR.COM Section 1 -Removing Internals -Lubrication -Re-assembly WSF Prepping Please De-gas, or remove all compressed air in your marker. Also Please have the safety in the “on” position. (Red ring on safety not visible) Before any internals are removed from the marker, all external parts need to be removed for easier access to the rest of the marker. To remove your barrel: Turn the barrel in a counter-clockwise motion to remove.
WWW.WARSENSOR.COM To remove R.I.S. Handle: Put the 6mm (CR-V6) allen wrench into the bottom of the R.I.S. handle. Turn in a Counter-Clockwise motion to remove (Note: It might be a little tough to remove at first, but stick with it.). To remove trigger group and bottom-line: To remove trigger group and bottom-line: Start off on the trigger group; take the smallest allen wrench (5/32) and take off both trigger screws (that are holding the trigger to the gun).
WWW.WARSENSOR.COM To remove Vertical Feed System: The Vertical Feed System has 2 screws, one on each side. To remove it, you use the smallest allen wrench (5/32) on the screws and turn them counter-clockwise. 7 WARSENSOR WSF User Manual Revision 1 printed Mail: info@warsensor.
WWW.WARSENSOR.COM To Disassemble the WSF Step 1: Remove rear Quick Strip pin. (Warning: Rear velocity adjuster is under pressure due to spring. Please secure when removing.) Step 2: Remove Internals. (Note: They will all come out together.) Step 3: Lube all necessary parts. (O-rings Only!) 8 WARSENSOR WSF User Manual Revision 1 printed Mail: info@warsensor.
WWW.WARSENSOR.COM Note: Repeat all steps in reverse for proper assembly of internal section. Pay close attention to the orientation of the striker and bolt assembly. The bolt has an air hole that needs to be facing down when installed or marker will not function! Striker Assembly Bolt Assembly 1st striker 2nd striker buffer 3rd striker spring 4th spring guide (pin) 5th velocity cap Bolt (all one part) To re-assemble please make sure your bolt and striker are connected properly.
WWW.WARSENSOR.COM Section 2 -Cocking Marker -Applying air source -Leaks Warning: The power system used on the Warsensor Field Marker contains HPA/CO2/N2. Never work on or disassemble the marker with compressed air source connected. This marker has a volumizer chamber which will retain pressure. Please make sure your marker is properly clear of all compression before disassembly. If working with CO2, avoid CO2 gas or escaping liquid to contact the skin, this will cause freezer burn on the contacted skin.
WWW.WARSENSOR.COM To run the power source off of the gun, without use of bottom-line. First you must remove the bottom-line asa from the trigger group. To run the power source off the gun, without use of bottom-line. You must then remove the rest of the bottom-line from the gun This is what you should be left with after you have removed the bottom-line. (Note: You may now attach a bottle, or remote line nipple directly to the gun) 11 WARSENSOR WSF User Manual Revision 1 printed Mail: info@warsensor.
WWW.WARSENSOR.COM Cocking your WSF To Cock your WSF: Firmly take the rear cocking bolt. Pull back, and release. Your marker is now cocked. Please make sure that your safety is on and you have your barrel plug in. Leaks Leaks when gassing up marker: If you are gassing up your marker and you hear leaking, please remember to cock your marker before you gas your marker up. Leaks out of the barrel. If you happen to have a leak out of your barrel, it might be because of the Cup Seal.
WWW.WARSENSOR.COM Section 3 -Adjusting Detent -Securing Hopper To adjust detent: Take pliers or a wrench and turn the angel style detent left to allow more movement and right to allow less movement. If balls roll out of your barrel, you must adjust your detent to allow less movement. To secure hopper: 1. Place hopper in adjustable feed neck. 2. Twist the feed neck collar right to secure hopper. 13 WARSENSOR WSF User Manual Revision 1 printed Mail: info@warsensor.
WWW.WARSENSOR.COM Section 4 -Adjusting Velocity -Checking FPS CHRONOGRAPHING INTRODUCTION This not only addresses some of the questions about chronographs and their proper use, but also to inform players how "less than ethical players" purposely circumvent safety rules. I realize that it may give people "ideas" on how to cheat, but if everyone knows about these nasty techniques, maybe more people will pick up on them.
WWW.WARSENSOR.COM so the radar beam is not interrupted by bushes, walls, tress and other obstacles. Always remember, the chronograph is NOT and impact sensor, so don't shoot it. IF THE MAXIMUM LIMIT IS 300 FEET PER SECOND (FPS) IS IT OKAY TO SET MY PAINTMARKER TO 300 FPS? ABSOLUTELY NOT! Due to ambient air temperature changes throughout the day, the effect of rapid firing on pressure and temperature of the CO2, along with a dozen other things, will effect the velocity by up to 15 fps.
WWW.WARSENSOR.COM bore, of the barrel is smaller than your paint, it will slow the velocity as well (because of increased friction between the barrel and the moving ball). Switching to a barrel which is of a larger bore (but similar outward appearance) will result in a drastic raising of velocity. Sometimes as much as 25 fps. PAINT. Old paint, which has swollen slightly, will give slower velocities. (Again, because of increased friction.) Load fresh paint and velocities start to climb.
