Use and Care Manual

(1 x 2 gallon Part A + 1 x 1 gallon Part B). Please note that the inner jugs are not filled to the top on purpose,
however they do contain the correct amount of epoxy. This packaging allows for safe shipment of the
materials. We do not recommend mixing all 2 gallons of Part A with the 1 Gallon of Part B at the same time as
it will pre harden, and this is not covered under warranty. Please keep in mind the working time once
mixed is approximately 15-25 minutes.
5a. MIXING A & B EPOXY
Rotate and shake the Part A Jug so the colored pigment that has settled at the bottom of the jug is spread
evenly in the Part A jug. Next, pour into the mixing bucket the amount of Part A you plan to use and mix with a
metal mixer to continue combining the pigment so you have a consistent color.
Pour 2 parts from Part A and 1 part of part B into a larger container or bucket that can hold at least the total
amount you are mixing. We STRONGLY recommend mixing up no more than HALF of the contents of each A
and B bucket, and then applying to the floor, and then repeating to avoid pre-hardening and having to rush
through the project.
ℹ Hint: Our packaging always is pre-measured at the proper mix ratio, but we do not recommend that you
mix up all of the ArmorPoxy at a time.
Mix the two components together for 2 to 3 minutes on medium to high speed with the drill attachment, but
not any longer. Move the mechanical mixer up and down and along the sides of the bucket through the
contents while spinning the container so that you get ALL of the material mixed, not just the material at the
bottom of the pail. Make sure to run the mixer along the sides of the pail too. Be careful to not mix at too high
of a speed, which could cause bubbles to form.
ℹ Hint: When mixing the Part A and Part B together you will notice ‘veins’ appear. These veins should
dissipate once mixing is complete. Be sure to scrape the sides and bottom of the containers to assure that all
the material is properly mixed. Improperly mixed resins will not harden properly or show color variations when
applied. If in doubt, mix a little longer. All Armorpoxy products are tested prior to shipping for hardening.
Improper hardening is not covered under the warranty as the only thing that can cause this is improper mixing
or very high floor moisture levels.
After the components are measured and mixed together you have approximately 25 MINUTES of working time
to apply at 70°F. Working times are shorter the warmer it is, and longer if it’s cooler. Work diligently and get
the mixed epoxy onto the floor. Once the epoxy is on the floor, you’ll have more working time than when it’s in
the bucket due to the floor’s temperature. Once the epoxy is out of the bucket and on the floor, work quickly
to avoid premature hardening and product failure. Premature hardening is not covered under warranty. You
can mix as much or as little of the material as you like, as long as you hold the mix ratio (2:1).
ℹ Hint: High Temperatures will shorten the amount of working time
ℹ Hint: Do not mix in direct sunlight. Keep mixed and unmixed material in the shade
ℹ Hint: Higher ambient temperatures can cause hardening prematurely. Getting the mixed material onto the
floor quickly will also help to slow down the curing process and extend working times.
ℹ Hint: Armorpoxy’s ArmorPower is a 100% solids resin and is a ‘thick’ coating. If you find that it is too thick
to apply due to temperature or other conditions, you can thin it a bit by adding up to 1/2 cup of xylene (also
known as xylol) to each gallon. Thinning will enhance workability and working time. Do not over-thin.
ℹ Hint: You must mix thoroughly. Make sure to move the mixer up & down throughout the mixture. Make sure
to mix along the sides and bottom. After completing mechanical mixing, use mixing sticks supplied to assure
7