Safety Instructions

d. Press the (Open/Close) button on the control panel, or the EJECT button on the remote control again
to close the CD tray.
e. Press " " to select your desire song；fast forward, press to fast forward through a track. You can then
press the playback button to start playback.
f. Press NEXT/F.F or PREV/F.R button to select your desire song.
g. Press "VOL+/-" to control the sound level.
h. Press "REP" once to repeat one song, the REP indication at the top left corner on the led display will flash.
Press "REP" one more time to repeat all songs in the track and the REP indication at the top left corner
on the led display will appear. Press "REP" again to cancel repeat function(When the songs are in MP3
format, you can repeat the songs in a folder).
i. To play songs randomly, press "REP" button until the led display "RAN" on the bottom of the display.
j. For programming, press "STOP" button to stop playback. Press "PRG/R" to enter programming mode.
The led display will flash and indicate "P 01", select the song that you want to program and then press
"PROG" again. Press "Play/Pause " to stop programming and start to playback the programmed
songs. This unit can program up to 20 songs（ Further info on this function on page 13）.
NOTE: Do not forcibly push the CD tray to close it as this may cause a malfunction.
USB/SD operation.
a.
Press "MODE" button until led display indicate " USB - - -"or “SD---”, then display will
show
number of folder, then number of songs and start playback.
b. Press "Next or Prev" or "F+/-10" to select your desire song.
c. Press "REP" once to repeat one song, the REP indication at the top left corner on the led display will
flash. Press the "REP" display "REP FOLDER" repeat album;Press "REP" one more time to repeat all
songs in the track and the REP indication at the top left corner on the led display will appear. Press
"REP" again to cancel repeat function.
d. To play songs randomly, press "REP" button until the led display "RAN" on the bottom of the display.
e. For programming, press "STOP" button to stop playback. Press "PRG/R" to enter programming mode.
The led display will flash and indicate "P 01", select the song that you want to program and then press
"PRG/R" again. Press "Play/Pause" to stop programming and start to playback the programmed
songs. This unit can program up to 20 songs.（ Further info on this function on page 13）.
NOTE: If the USB or SD drive contains audio files which are not compatible with the Jukebox, the Jukebox will
not be able to read them, so they will not be included in the count of tracks on the disc, and they will not play.
IMPORTANT: For optimum performance it is recommended to only use a USB 2.0 flash drive (not a 3.0
version).
NOTE: If the SD card contains audio files which are not compatible with the Jukebox, the Jukebox will not be
able to read them, so they will not be included in the count of tracks on the disc, and they will not play.
Please note: THE USB socket outputs dc voltage of 5V1A .
8
REMOTE CONTROL DIAGRAM
13
Note：The best transmission distance of the remote control:
within 5 meters without barrier (Angle plus or minus 30°).
PROGRAM:
a. While playing back from a music source(In the case of
CDMP3 or USB/SD playback state), press the stop button.
b. Press the program button to enter the program mode. The
word PROG will flash in the bottom left corner of the
display screen. A position number will also be flashing on
the screen (eg: p01).
c. Press the next or back buttons to select which track you
want to program into position. When you have made
your selection, press the program button to save it..
d. You can then repeat the same steps to fill in more
positions.
e. When done, press play to begin your music playback.
You can do this at any stage once you have
programmed the amount of tracks you want.
f. At any stage during the program process you can
press stop to cancel.
g. 'FULL' will display on the LCD screen when the Max
amount of memory location have had been filled.