Instructions / Assembly

ManualsBrandsARK DESIGN ManualsBifold Doors30 in. x 80.5 in. 3-Lite Tempered Frosted Glass Solid Core White Prefinished Composite Pivot Bifold Door with Hardware

• Make sure the installation area is free of clutter

TOOLS REQUIRED

Phillips Screwdriver Cordless Drill

Tape Measure

Level Pencil

3/16" Drill Bit

PLEASE READ CAREFULLY

General safety rules follow

• Read all instructions carefully

• Protect your eyes when handling metal parts, wear safety goggles

INSTALLATION INSTRUCTIONS

Pivot Closet Doors

Summary of content (8 pages)

PAGE 1
Pivot Closet Doors INSTALLATION INSTRUCTIONS PLEASE READ CAREFULLY General safety rules follow • Read all instructions carefully • Protect your eyes when handling metal parts, wear safety goggles • Make sure the installation area is free of clutter TOOLS REQUIRED Phillips Screwdriver Cordless Drill Tape Measure 3/16" Drill Bit Level Pencil
PAGE 2
IMPORTANT VERIFY THAT ALL PARTS ARE INCLUDED IN THE PACKAGING. IF ANY PARTS ARE MISSING, DO NOT RETURN THIS PRODUCT TO THE STORE.
PAGE 3
1 Top location and track installation A 2-1/4 in 2-1/4 in Step11 Step NOTE The securing screws should face outwards. Insert toptop pivot to both sidessides of theof track. Inserteach each pivot to both the track. Note: The A securing screws should face outwards. Note: The securing screws should face outwards. 2-1/4 in 2-1/4 in Measure and line uptop the center ofsides the pivot to 2-1/4 in and line up Insert each pivot to both of the track.
PAGE 4
2 A Door panel hardware preparation Step 3 1/2 in 1/2 in 1/2 in 1/2 in 2 in 2 in 2 in 2 in B 2 in 2 in 2 in 2 in the edge of the door. This will also ensure the pivot is Note: Secure the mounting plate with the locking latch located 2" from the edge of at the back of the door panel. the door. Use 1-1/4" pan head screws to secure into place.
PAGE 5
3 Jamb pivot bracket and floor bumper installation Step 4 A B Position the bottom jamb pivot braclet 13/16 in from the front of the opening. Using a Phillips Screwdriver, insert 1-1/2 in flat head screws and secure using all three holes. 3-1/2 in Extend the bracket so that the hole location is 2-1/4 in and secure in place by tightening the screw.
PAGE 6
engaged inside the mounting plate. Close the locking latch to secure the panel in place. 4 A Door panel installation and adjustment Step 6 B Open the locking latch on the mounting plate and position the door panel so that the pivot bolt can be engaged inside the mounting plate. Close the locking latch to secure the panel in place. Lower the door panel so that the bottom pivot engages the bottom jamb pivot bracket. The spring action will suspend the door panel.
PAGE 7
the header. 5 Magnetic catch and fascia installation A A With both door panels installed, secure each magnet plate holders to the back of the door panels, flush to the corners using the ⅝" pan head screws. With both door panels closed, position the magnet bracket in place so that the magnetic strips make contact with the plate holders inside the opening and secure the bracket in position using the 2" screws into the header.
PAGE 8
6 Door pull installation A Step 9 Measure up from the bottom of the inside from the opening edge 1-1/2 knob locations. Pilot hole 3/16 in holes from the fro panels and thread the screws in fro Attach the pulls from the front tighte complete the installation. A Measure up from the bottom of the door 36" and inside from the opening edge 1-½" to determine knob locations. Pilot hole 3/16" holes from the front of the door panels and thread the screws in from the back.