| AF-9400PV2R Users’ Manual Notice This manual can help you to become familiar with how-to-use and the many great features of the personal video recorder AF-9400PV2R. All the safety and operating instructions should be read before the AF-9400PV2R is operated. Please keep the manual in a fixed place so that it can be easily referred to later. The following symbols will serve as follows: Indicates any other additional important or helpful information. Indicates warning information.
Contents | 3 Safety and Precautions Install on an even plane. Don’t install in the cold or under direct sunlight. Leave a minimum 10cm gap all around the product. Don’t disassemble, repair, or reorganize the product.
| AF-9400PV2R Users’ Manual Table of Contents Chapter 1. Before You Begin ························ 5 1.1 Features ············································ 6 1.2 Package Contents ···························· 8 1.3 Names of Each Part ························· 9 1.3.1 Front Panel ···································· 9 1.3.2 Rear Panel ··································· 10 1.4 Names of Remote Button ··············· 12 1.4.1 Names of Remote Button ············ 12 1.4.
Chapter 1 Before You Begin
| AF-9400PV2R Users’ Manual 1.1 Features With the new AF-9400PV2R you can watch different programs at two rooms simultaneously. You may also record two programs each other at the same time or watch one while recording the other on the built-in hard disk. Enjoy the convenience of Radio Frequency remote control! It doesn't get any better than this.
Ch1.
| AF-9400PV2R Users’ Manual 1.2 Package Contents Please check to make sure the following contents are in the product package. z z Product contents may be subject to change. Cables not specified above must be purchased separately.
Ch1. Before You Begin | 9 1.3 Names of Each Part 1.3.1 Front Panel 1. Power Switches the product on/off. 2. CH ▲/▼ Changes the TV/Radio channel Up/Down. 3. VOL ◄/► Increases or decreases TV/Radio volume level or change the value of an item in menu mode. 4. OK Selects a menu or confirms the user’s action and displays the channel list during watching a TV. 5. MENU Displays the menu OSD. 6. EXIT Exits from the current menu or cancels the current operation in menu mode. 7. CI Slots Inserts two CI modules. 8.
| AF-9400PV2R Users’ Manual 1.3.2 Rear Panel 1. LNB IN 1, 2 Connect a coaxial cable of your LNB to this connector up to two cables. 2. LNB OUT 1, 2 Connect LNB OUT to another set-top box or LNB OUT1 to LNB IN2 via a Loop-through cable 3. USB ( ) Connect USB to your PC to copy MP3 file on PC. 4. AUDIO L/R ( ) Connect AUDIO L/R to the matching Audio Inputs of your TV/VCR via a RCA cable. 5. VIDEO ( ) Connect VIDEO to video input of your TV or VCR via a RCA cable. 6.
Ch1. Before You Begin | 11 11. S/PDIF ( ) Connect S/PDIF to audio input of your amplifier with optical digital port via an optical cable. ) 12. ANT IN ( Connect ANT IN to your TV antenna or cable TV system. ) 13. TV OUT ( Connect TV OUT to your TV antenna input, and then the room changing function is in operation. 14. RF RCU RECEIVER ( ) Connect the port to the phone-jack of RF receiver. 15. VIDEO ( ) Connect VIDEO to video input of TV2 or VCR via a RCA cable. 16.
| AF-9400PV2R Users’ Manual 1.4 Names of Remote Button 1.4.1 Names of Remote Button STANDBY To switch the product On or Standby. MUTE ( ) To mute the sound. NUMERICAL BUTTONS To enter a TV/Radio channel number or characters. HELP To display all help icons. TV/RAD To switch the product TV or Radio. SAT To select the specific satellite. FAV You can register the favorite channels by pressing the “MENU” button, and then change the channel mode by pressing the “FAV” button.
Ch1. Before You Begin | 13 CH ▲/▼ Teletext ( To change the TV/radio channels Up/Down. To display the teletext information about the channel if applicable. VOL ◄/► To increase or decrease TV/Radio volume level or change the value of an item with preprogrammed values. The “◄” button can be used as a backspace to cancel the numerical input. Subtitle ( , hereafter “Blue”) To display the provided subtitle language lists of the current channel. PVR To show the recorded file or MP3 file list.
| AF-9400PVR Users’ Manual Repeat ( To show the PIP channel list. ) Whenever you press the button, the repeat mode changes sequentially such as a specified block repeat→all block repeat→ the repeat mode Off. Cutting Data ( Swapping PIP and Main Screen ( ) To swap between the PIP screen and the Main screen. ) To cut the desired section from the recorded file. Changing the Position of the PIP ( ) To change the position of the PIP screen.
Ch1. Before You Begin | 15 1.4.2 Remote Control Extender 1) Introduction This Remote Control Extender uses the smartest and easiest technology in extending the remote control operation. By installing the transmitter in the battery pocket only, your remote control now detects the key signals and transmits them far away. This extender kit (called Remote Control Extender) includes transmitter (battery type), receiver (UFO shape), two 2/3 rechargeable batteries and AAA sleeve.
| AF-9400PV2R Users’ Manual 2. floor to floor - control satellite / cable in living room from the second floor 3) Installing the RF Transmitter Your remote control will use several AAA size batteries, normally 2 to 4. Please install RF transmitter instead of a battery (one of batteries only). Below shows the battery AAA size using in normal remote control.
Ch2. Connections | 17 5) Function Switch Selection (A, B, C) You will find slide switch on the bottom of receiver if you remove the plastic case. The positions A, B, C are used to set the receiver to different remote controls. The factory setting is on position C (Most of remote control use position C) A: 56KHz (a few special remote) B: 38KHz (most of remote controls) C: sensitivity lower (external interference etc) 6) erference To determine whether your extender is causing the interference.
| AF-9400PV2R Users’ Manual 3. Install the full-charged battery in transmitter and insert old battery into the 2/3 AAA pocket for recharging. Lose the cover. While the battery is recharging, the LED CHG (BAT) will blink in the receiver. LED will blink when the recharging battery is inserted in the pocket. Full recharging time is approx. 12 hours and 6-8 hours when the battery is not fully flat. After replacement of rechargeable battery, you need to test the function.
Ch2.
| AF-9400PV2R Users’ Manual This chapter describes how to connect the product to your home entertainment system. Choose the most appropriate procedure depending on your environments. : If you encounter with any problems or have any questions during connecting the product, please contact your local product distributor. 2.1 Connecting a TV & VCR [ For TV1 ] 1. Connecting a TV with RF ( ) 1) Connect the TV antenna to the ANT IN of the product. 2) Connect the RF-IN of TV to the TV OUT of the product.
Ch2. Connections | 21 2. Connecting a TV and VCR with RF ( ) 1) Connect the TV antenna to the ANT IN of the product. 2) Connect the RF-IN of VCR to the TV OUT of the product. 3) Connect the RF-OUT of VCR to the RF-IN of TV. 4) Connect the Video and Audio of TV to the VIDEO and AUDIO L/R of the product. 5) Go to section 2.2 Connecting to Dish, and then connect your dish. 3. Connecting a TV and VCR with a Scart Cable ( ) 1) Connect the TV antenna to ANT IN of the product.
| AF-9400PV2R Users’ Manual [ For TV2 ] 4. Connecting a TV 2 with a RF ( ) 1) To split antenna signal both TV1 and TV2, connect the Splitter to the TV OUT of the product. 2) Connect the RF-OUT of the Splitter to the RF-IN of TV2. And connect the other port of the Splitter to the RF IN of TV1. 3) Connect the Video and Audio of TV to the VIDEO and AUDIO L/R of the product. 4) To use the RF remote control for TV2 viewer, connect the RF RCU Receiver of the product to the RF remote control receiver.
Ch2. Connections | 23 2.2 Connecting a Dish AF-9400PV2R provides three antenna modes(Loop, twin, T1/T2). Refer to Chapter 3.4 System Setup for detailed information. Case1) One Antenna and a loop-through cable: If you connect one antenna cable to the LNB1 IN and connect the LNB1 Out to the LNB2 IN with a loop-through cable. When the channel of LNB1 is recorded, you can switch and view channels which have the same polarity or transponder with the recorded channel.
| AF-9400PV2R Users’ Manual 2.3 Connect the Optical S/PDIF If you watch a program encoded by a Dolby Digital, you can enjoy the higher quality sound of the Dolby Digital audio. Connect the optical S/PDIF to Dolby digital decoder or Digital television. 2.4 Connect the USB Connect the USB to your PC to copy MP3 file from PC.
Ch2. Connections | 25 2.5 Starting Up 1. Connect the power cord of the product to a power outlet and press the “Power” button at the rear panel to turn the product on. 2. The first time you power up the product, it will display the initial screen, then some parameters for system configuration should be set. Refer to the following chapter for detailed information about the basic settings.
| AF-9400PV2R Users’ Manual
Ch1.
| AF-9400PV2R Users’ Manual If you use the product for the first time after connecting, you have to perform basic settings. Once the setup procedure is finished successfully, you can start watching TV or listening to radio. Turn on your TV and the product. Follow the instruction on the screen. Press the “MENU” button to save the previous input information and exit the basic settings.
Ch3. Basic Settings | 29 3.2 Time Setting You can set the current time. 1. Select Time Mode between GMT Offset and Local time using the “◀▶” button. 2. Select the appropriate GMT Offset value using the “◀▶” button or enter the local time using the “0~9” button. 3. Press the “Red” button to move to the next setting. Or press the “EXIT” button to return to the previous screen. 3.3 Output Setting You can set the audio and video output such as video, TV screen mode, SPDIF, TV type, RF Type and etc.
| AF-9400PV2R Users’ Manual 3.4 System Setup You can set the antenna’s properties such as system, tuner, longitude, latitude, and etc. z z z z z System: Fixed, DiSEqC, USALs Tuner: T1/T2, Loop, Twin Longitude, Latitude : You can enter the value using the “0~9” button. Move : Stop, East, West Limit Setting : Disable, Enable, Set East, Set West 1. Select the system value using the “◀▶” button. The default value is ‘Fixed’. 2. Select the tuner according to the connection type using the “◀▶” button.
Ch3. Basic Settings | 31 3.5 Antenna Setting ( ) You can set the antenna's properties to watch the program. This setting is provided to the only TV1 viewer. : If TV1 viewer selects Search to ‘Enable’ at the Setup-TV2 Control menu, TV2 viewer can also set the antenna setting. Refer to Chapter 5.3.8 TV2 Control for more information. 1. Select the Satellite name using the “◀▶” button. 2. Show the tuner value according to the tuner type at the previous step(1, 2/Loop/Twin).
| AF-9400PV2R Users’ Manual 8. Select the desired item using the “OK” button and press the “Red” button to search the channels. 9. When completing Channel Search, the following message will appear. Move cursor to the “OK” button and press the “OK” button to save the changes. If you encounter with any problems or have any questions when setting up the antenna, please contact your local product installer or distributor. Now you have completed all steps required for watching TV or listening to radio.
Ch1.
| AF-9400PV2R Users’ Manual [Basic Functions ] 4.1 Changing Channels There are several ways to change the channels. If you are TV2 viewer, the ‘2’ symbol will appear. z z z Press the “▲▼ ” button on the remote control to access the channels sequentially. Enter your desired channel number using the “0~9“ buttons directly. Press the “OK” button to display TV channel list, and then select the desired channel. 4.2 Adjusting Volume You can change the volume level of the current channel.
Ch4. Operations | 35 4.3 Viewing Program Information You can view the 3 steps information window by pressing the “INFO” button while watching a program. Press the “EXIT” or “INFO” button to hide the program information. Step 1: Basic Information The Basic Information is displayed as following on the screen. Step 2: EPG Information You can see EPG information about the current program. Press the “INFO” button to view EPG information during the Basic information is displayed.
| AF-9400PV2R Users’ Manual 4.4 Switching TV and Radio Press the “TV/RADIO” button to switch TV or Radio. If you are TV2 viewer, the ‘2’ symbol will appear. 4.5 Freezing Screen/Zooming Screen You can zoom in or out the current screen. 1. Press the “EXIT/ZOOM” button to select zooming mode. 2. Press the “Red” button to zoom in the screen or the “Green” button to zoom out the screen. Or press the “◄►▲▼” button to change the position of the frame. 3.
Ch4. Operations | 37 4.6 Changing Subtitle Language If the current program provides Subtitle information, you can select the subtitle language. 1. Press the “ ” button to display the subtitle language list. 2. Select the desired subtitle language using the “▲▼” button, and press the “OK” button. The subtitle language will be displayed at the bottom of the screen. Subtitle language 3. Select ‘OFF’ from the subtitle language list not to display subtitle from the screen.
| AF-9400PV2R Users’ Manual 4.7 Changing Audio Language If the current program provides multiple audio languages, you can select the desired language. 1. Press the “ ” button to display the audio language list. 2. Select the desired audio language using the “▲▼” button, and press the “OK” button. The audio language will be changed immediately. : You can select a default audio language by pressing the “MENU” button and selecting the Setup–Language Setting–Audio menu in order. Refer to Chapter 5.3.
Ch4. Operations | 39 [ Advanced Functions ] 4.9 Managing Channel List 4.9.1 Displaying Channel List You can see various channel lists and change the channels from the channel list more conveniently. 1. Press the “OK” button while watching a program to display the selected channel list. 2. Move to the desired channel using the “▲▼” button and press the “OK” button to change the channel. Press the “FAV” button to switch among the channel modes such as ‘ALL, FAV1~4, etc’. Refer to Chapter 4.
| AF-9400PV2R Users’ Manual 4.9.2 Searching Channel You can search the specific channel among various channel lists more conveniently. 1. Press the “OK” button while watching a program to display the selected channel list. 2. Press the “Green” button to sort the channel lists by alphabetic order. : Press the “Red” button to sort the channel groups by FTA/CASI or Tuner. 3. Press the “2(abc)~9(wxyz)” button to search the channel lists which have same initial.
Ch4. Operations | 41 4.9.3 Viewing Multi-Channels Window You can display multi-channels window and select a channel to watch. 1. Press the “OK” button while watching a program to display the selected channel list. 2. Press the “Yellow” button to display the number of the multi-channel among 2, 4, 9, 10, 13, or 16. Move to the desired number of window using the “▲▼” button and press the “OK” button to display multi-channels. 3. Move to the desired channel using the “◄►” button to watch the program.
| AF-9400PV2R Users’ Manual 4.9.4 Changing Satellite Group You can change the satellite group. 1. Press the “OK” button while watching a program to display the selected channel list. 2. Press the “SAT” button while the channel list is displayed to view the satellite group lists. 3. Select the desired channel group using the “OK” button to display its sub-groups. 4. Press the “EXIT” button to return to the previous screen.
Ch4. Operations | 43 4.9.5 Editing Channels You can edit(such as lock, delete, move, and rename) all channels or each channel. Press the “EXIT” or “MENU” button to save the changes and return to the previous menu. 1. Press the “MENU” button. 2. ①!Move to the Edit menu using the “◄►” button, and press the “OK” button. ②!Select the Edit Channel menu using the “OK” button.!③ Enter your password using the “ 0~9” buttons. The default password is 0000.
| AF-9400PV2R Users’ Manual 4.10 Managing Favorite Channel Lists You can create and edit favorite channel list(s) or group(s). 1. Press the “MENU” button. 2. ①!Move to the Edit menu using the “◄►” button, and press the “OK” button. ②!Select the Edit Favorite menu using the “OK” button.!③ Enter your password using the “ 0~9” buttons. The default password is 0000. If you select Menu Lock to ‘No’ at the Setup-Lock Control, you don’t have to enter the password. Refer to Chapter 5.3.
Ch4. Operations | 45 4. You can edit favorite channel list(s) or group(s). If you want to add channel(s), select the desired channel, and then press the “OK” button. 5. Whenever you press the “MENU” or “EXIT” button after editing favorite channel, the confirmation message will appear. Move cursor to the “OK” button and press the “OK” button to save the changes.
| AF-9400PV2R Users’ Manual 4.11 Changing Channel Mode You can change the channel mode by group. 1. Whenever you press the “FAV” button, the channel mode changes sequentially such as ALL→FAV1→ FAV2→…→All. 2. Press the “OK” button to display All Channel or Favorite Channel lists according to the current channel mode.
Ch4. Operations | 47 4.12 Viewing Program Guide The Program Guide shows program information about each channel-by date and time. 1. Press the “EPG” button. z Red : Views daily schedule for the selected channel. z Green: Views the channel window. z Blue: Views the Media highway EPG. It is available only when the program provides the media highway EPG service. 2. Press the “Red” button to view daily schedule for the selected channel. z ▲▼ : Moves to other desired channel.
| AF-9400PV2R Users’ Manual 4.13 Viewing PIP The advanced PIP function allows you to watch two different screens at once, even if you don’t have a VCR connected to your TV. If you change the main screen channel into the one of different transponder, the PIP screen will be disappeared automatically. You can see the PIP screen at radio mode, recording mode and playback mode. 1. Press the “ ” button to show the PIP screen and the PIP channel information bar on the screen.
Ch4. Operations | 49 3. Press the “ ” button to change the PIP channel. The PIP channel lists will appear. You can move to the desired channel using the “▲▼” button, and then press the “OK” button. You can choose the only channel on the PIP channel lists. The number of PIP channels is variable according to the main screen channel state. 4. Press the “ ” button to change the position of the PIP screen.
| AF-9400PV2R Users’ Manual 4.14 Recording & Playback AF-9400PV2R provides three recording modes such as the instant recording, the normal recording, and the reservation recording. : z If TV1 viewer selects PVR to ‘Enable’ at the Setup-TV2 Control menu in TV1, TV2 viewer can record the program. Refer to Chapter 5.3.8 TV2 Control for more information. z The recorded files of TV1 and TV2 are summed up to 4 files simultaneously. 4.14.
Ch4. Operations | 51 4.14.2 Normal Recording The normal recording function saves the programs up to 4 programs at once. You can also watch program using functions such as rewind, fast forward, replay, pause, and recording. 1. Press the “MENU” button to set the recording options. ① Move to the HDD menu using the “◀▶” button, and press the “OK” button. ②!Move to the Recording sub-menu using the “▲▼” button, and press the “OK” button.! ③ Set the recording options, and press the “MENU” button.
| AF-9400PV2R Users’ Manual z ‘1’ means the file is recording by TV1 viewer and ‘2’ means the file is recording by TV2 viewer. z If you are TV1 viewer, you can stop recording all files in ‘1’ and ‘2’. If you are TV2 viewer, however, you can stop recording the files in only ‘2’. 4. ① Move to the desired file using the “▲▼” button, and press the “ “EXIT” and “OK” button then the recording is stopped. : There is limitation to change the channel during the recording. ” button.
Ch4. Operations | 53 4.14.3 Reservation Recording The reservation recording function saves the desired programs automatically. You can watch program using functions such as rewind, fast forward, replay, pause, and recording. 1. Press the “MENU” button to set the reservation recording options. ① Move to the Setup menu using the “◀▶” button, and press the “OK” button. ②!Move to the Timer Setting sub-menu using the “▲▼” button, and press the “OK” button.
| AF-9400PV2R Users’ Manual 3. Set the Mode to ‘Record’ using the “◀▶” button, and then set the Cycle, Time, and Duration. 4. Whenever you press the “MENU” button after completing setup, the following message will appear. Move cursor to the “OK” button and press the “OK” button to save the changes. 4.14.4 Recorded File Playback You can play the recorded file by selecting a desired file. But you can’t play the recorded files on TV1 and TV2 simultaneously. 1.
Ch4. Operations | 55 ① You can record the playback file during the playback. ② The file name on recording is in different color. ③ You can’t change the channel during the recorded file playback. You should stop the playback, and then change the channel. ④ If you choose the recording file, the channel is changed to the same channel. 3. Press the “ ” button to display the progress bar. And you can perform time shift operations like ), pause ( ), repeat( ), and replay( ).
| AF-9400PV2R Users’ Manual 4.14.5 MP3 File Playback You can listen to the MP3 file by selecting a desired file. 1. Press the “PVR” button to display the file list. Or press the “OK” button during the playback. 2. Press the “◀▶” button to show the MP3 file list. The MP3 list appears. Select the desired file to playback using the “▲▼” button, and then press the “OK”. 3. The MP3 progress bar appears. 4. Press the “MENU” button to exit the MP3 file playback.
Ch4. Operations | 57 4.14.6 Bookmark You can search positions very quickly and easily by bookmark during the recorded file playback. 1. Press the “ ” button at the desired position to set a bookmark during a recorded file playback. The bookmark OSD will appear on the upper right corner during on air mode. : Up to 64 bookmarks for one recorded file can be set up. 2. Press the “ ” button again to delete a bookmark. 3. Press the “ ” button to go to the next bookmark. 4.14.
| AF-9400PV2R Users’ Manual 4.15 Switching Rooms This function is helpful to get rid of your trouble. You don’t have to move the cables any more. Just only pressing the button, you can switch rooms between the TV1 and the TV2. You can watch the other room’s program and exchange the various configuration of TV such as Favorite channel, Lock, Language, and etc. 1. Press the “ ” button. The programs of the TV1 and TV2 viewer are exchanged. You can watch the other room’s program.
Ch4. Operations | 59 4.17 Viewing Teletext Teletext Service is text data service from Service Provider. It is available only when the program provides teletext data service. 1. Press the “ ” button. Teletext Service Data is displayed. Select the desired language using the “▲▼” button, and press the “OK” button. 2. Select the page using the “0~9” buttons(100~899). 3. Press the “EXIT” button to the previous screen. 4.18 Changing STB/TV This function is used for receiving a signal through the RF modulator.
| AF-9400PV2R Users’ Manual
Ch1.
| AF-9400PV2R Users’ Manual This chapter describes how to search for channels, edit channel, setup for language(OSD, Timer, etc.), show tools, and etc. The setting menus are different according to TV1 and TV2. 1. Press the “MENU” button to display the Menu OSD. 2. Move to the appropriate Menu using the “◀▶” button, and then press the “OK” button to select the menu. 3. Move to the appropriate Menu using the “▲▼” button, and then press the “OK” button to select the sub-menu. 4.
Ch5 Settings | 63 5.1 Search Channel ( ) You can set the antenna's properties and search channel. z Antenna Setting: Sets the Antenna properties. z Automatic Search: Searches the satellite automatically. z Manual Search: channel manually. Searches the z Advanced Search: Finds the specific channel. z System Setup : Sets Antenna angle. : The menu isn’t provided to TV2 viewer according to the default value.
| AF-9400PV2R Users’ Manual : If you select ‘T1/T2’ at the Search Channel-System setup menu, you should set the antenna setting of ‘1’ and ‘2’ separately. Select ‘1’ to search the channels for ‘T1’, and then select ‘2’ to search the channels for ‘T2’. 3. Set the transponder value for the satellite using the “◀▶” button. 4. Set the LNB power and frequency type using the “◀▶” button. : When using Universal LNB, select Universal for LNB type (9750/10600 (MHz)).
Ch5 Settings | 65 5.1.2 Automatic Search ( ) After antenna setting, you can automatically search for satellites. ①! Move to the Search Channel menu using the “◀▶” button, and press the “OK” button. ②!Move to the Automatic Search sub-menu using the “▲▼” button, and press the “OK” button.! ③ Enter your password using the “ 0~9” buttons. The default password is 0000. z ▲▼: Moves to other satellite. z ◀▶: Moves to other column. z OK: Selects the satellite z Red: Starts to search the satellite.
| AF-9400PV2R Users’ Manual 5.1.3 Manual Search ( ) After antenna setting, you can search channel(s) from the selected satellite if you know the transponder information. ①! Move to the Search Channel menu using the “◀▶” button, and press the “OK” button. ② Move to the Manual Search sub-menu using the “▲▼” button, and press the “OK” button.! ③ Enter your password using the “ 0~9” buttons. The default password is 0000.
Ch5 Settings | 67 5.1.4 Advanced Search ( ) You can find the desired channel by entering Video, Audio and PCR PID directly. ①! Move to the Search Channel menu using the “◀▶” button, and press the “OK” button. ②! Move to the Advanced Search sub-menu using the “▲▼” button, and press the “OK” button.! ③ Enter your password using the “ 0~9” buttons. The default password is 0000. z z z Tuner : 1, 2/Loop/ twin Video, Audio, PCR PID: You can enter the value using the “0~9” button. Refer to chapter 4.
| AF-9400PV2R Users’ Manual 1. Enter the Longitude and Latitude value directly using the “0~9” button. 2. When the entering angle values are finished, the confirmation message will appear. Move cursor to the “OK” button and press the “OK” button to save the changes. 5.2 Edit Channel You can edit channel(s), favorite channel(s), transponder and remove satellite. The setting menus are different according to TV1 and TV2. z Edit Channel: Locks/deletes/moves/renames channel.
Ch5 Settings | 69 5.2.2 Edit Favorite You can create and edit favorite channel list(s) or group(s). Refer to Chapter 4.10 Managing Favorite Channel Lists for more information. 5.2.3 Edit Transponder ( ) You can create, edit, and delete transponder and satellite. The menu is provided to only TV1 viewer. 1. ① Move to the Edit menu using the “◀▶” button, and press the “OK” button. ②!Move to the Edit Transponder sub-menu using the “▲▼” button, and press the “OK” button.
| AF-9400PV2R Users’ Manual 5.2.4 Remove Satellite ( ) You can remove the channel(s). The menu is provided to only TV1 viewer. 1. ①! Move to the Edit menu using the “◀▶” button, and press the “OK” button. ②!Move to the Remove Satellite sub-menu using the “▲▼” button, and press the “OK” button.! ③ Enter your password using the “ 0~9” buttons. The default password is 0000. 2. Press the “OK” button to select the satellite. 3. Press the “Red” button to select the deleted channel(s) for the satellite. 4.
Ch5 Settings | 71 5.3 Setup You can setup additional function such as Language Setting, OSD Setting, Output Setting, Time & Timer Setting, Lock Control, Media Highway EPG, and TV2 Control. The setting menus are different according to TV1 and TV2. z Language Setting: Selects the language. z OSD Setting: Sets the OSD. z Output Setting: Sets the connected devices. z Time & Timer Setting: Sets the time and timer. z Lock Control: Sets the system lock. z Media Highway EPG: Views the media highway EPG.
| AF-9400PV2R Users’ Manual 5.3.2 OSD Setting You can set the interval for the program information bar hide-out. z ◀▶: Selects the desired value. z ▲▼: Moves to other items. z MENU: Exits the menu. z EXIT: Returns to the previous screen. 5.3.3 Output Setting You can set the connected devices such as TV screen mode, Dolby AC-3 decoder, and etc. The setting items are different according to TV1 and TV2. z ◀▶: Selects the desired value. z ▲▼: Moves to other items. z MENU: Exits the menu.
Ch5 Settings | 73 5.3.4 Time Setting You can set the current time. Refer to Chapter 3.2 Time Setting for more information. 5.3.5 Timer Setting You can set the timer. z ◀▶: Selects the desired value. z ▲▼: Moves to other items. z 0~9: Enters the time. z MENU: Exits the menu. z EXIT: Returns to the previous screen. 5.3.6 Lock Control You can prevent wrong usage by using the Install/Menu/IRD Lock and Password. z ◀▶: Selects the desired value. z ▲▼: Moves to other items. z MENU: Exits the menu.
| AF-9400PV2R Users’ Manual 5.3.7 Media Highway EPG ( ) You can view the media highway EPG. The menu is provided to only TV1 viewer. z ◀▶: Selects the desired value. z ▲▼: Moves to other items. z MENU: Exits the menu. z EXIT: Returns to the previous screen. 5.3.8 TV2 Control ( ) You can set the TV2 control menu. The menu is provided to only TV1 viewer. z Search: Enables TV2 viewer to search the channels. z Edit: Enables TV2 viewer to edit the channels.
Ch5 Settings | 75 5.4 Tools You can view the product information, restore to the default setting, upgrade the program, and etc. z Information: Shows the product version. z Factory Setting: Restores to the default setting. z Software Transfer: Transfers the program. This menu is provided only to TV1. z Utility, Game: Provides the convenient utilities(calendar and calculator) and game. ①! Move to the Tools menu using the “◀▶” button, and press the “OK” button.
| AF-9400PV2R Users’ Manual 5.6 HDD You can view the hard disk information, the hard disk format, the recording, and the instant recording. z HDD Information: Shows the hard disk information such as the model name, the remained storage, and etc. z HDD Format: Formats the hard disk. z Recording: Records the programs. z Instant Recording: Records the programs temporarily. z Descrambling: Descrambles the scrambled file. ①! Move to the HDD menu using the “◀▶” button, and press the “OK” button.
Ch1.
| AF-9400PV2R Users’ Manual 6.1 Trouble Shooting If the product does not work properly after checking it, please contact your local dealer. Don't open the product. It may result in a dangerous electric shock and will invalidate your warranty Problem The display on front panel does not light up. No picture, no sound. Possible Causes What to do The main power cable is not connected. Check that the main power cable is plugged in to the wall outlet.
Ch6. Appendix | 79 6.2 Specification 1. Tuner & Demodulator RF input Connector F-type X 2 female RF Loop-through Connector F-type X 2 female RF Frequency Range 950Mhz to 2150 MHz Input Impedance 75 Ω normal Input Signal Level -65 dBm to -25 dBm Loop-through Gain 0 dB Typical / ±5dB Max IF Frequency Zero IF Vertical : 13.0Vdc LNB POWER Horizontal : 18.0Vdc Current : 500mA(MAX) Overload Protection LNB Control DiSEqC 1.0, 1.1, 1.
| AF-9400PV2R Users’ Manual 3. HDD Type ATA – UDMA66 HDD Size 3.5 inch of 80Gbyte and More HDD of VENDOR Samsung, Seagate, Maxtor 4. Conditional Access System PCMCIA 2 slots of DVB CI standard Smart Card Reader 1 Smart card reader for embedded CAS (*optional) 5.
Ch6. Appendix | 81 6. 0/12V 0/12V 12V, 50mA 7. RF RCU Receiver RF 433.92MHz(30+ meters) 8. RF-Modulator RF-Connector 75Ω , IEC 169-2,Male/Female Frequency 470 to 860MHz Output Channel CH21~69 for the Demodulator TV Standard PAL BG/I/DK , NTSC Preset Channel CH 21 (or TBD), Changeable by Menu 9.
| AF-9400PV2R Users’ Manual ARN/AF-9400PV2R/EOSD2.0_REV1.
