Installation Guide

ManualsBrandsAries ManualsAutomotiveActionTrac 79-Inch Retractable Powered Running Boards, Select Chevrolet Silverado, GMC Sierra 1500, 2500, 3500 Crew Cab

NEED ASSISTANCE?

•

844.278.4357

•

PAGE 1

POWERED RUNNING BOARDS

INSTALLATION MANUAL

Parts List

Driver / left running board*

Passenger / right running board*

Mounting bracket, standard

2 Mounting bracket, middle

6 Step bracket

8 L-br acket

2 Def tank bracket

6 T-rails

8 Hex bolt, M8

8 Flat washer, M8

8 Lock washer, M8

4 Clip nut, M8

24 Flat washer, 5/16"

24 Nylock nut, 5/16"

12 Hex bolt, 7/16" x 1"

24 Flat washer, 7/16"

12 Lock washer, 7/16"

12 Hex nut, 7/16"

Rubber grommet

Door sensor

2 Door sensor extension

Magnet

Alcohol wipe

Power switch

Circuit board

Anti-seize

Wire loom

Wiring harness, two-piece

LED light

2 LED light bracket

4 Double-sided foam tape, 3/4" x 3/4"

8 Double-sided foam tape, 1/2" x 1/2"

* Running boards sold separately

Tools Required

Ratchet Drill

Socket set Drill bit set

Zip ties Level

Level of Difﬁculty

Moderate

Notes and Maintenance

Before you begin installation, read all instructions thoroughly.

Proper tools will improve the quality of installation and reduce the time required.

No maintenance required on waterproof harness or water-resistant motors.

If mud or dirt is built up on the steps, simply spray them off and let them air dry.

Mild automotive detergent may be used to clean the product. Do not use dish detergent, abrasive

cleaners, abrasive pads, wire brushes or other similar products that may damage the ﬁnish.

Periodic inspection of all wires and connections should be

performed to ensure there is no visible damage or loose connections.

Refer to the last page of this manual for troubleshooting,

warranty and product registration information.

Refer to the table to the left when securing hardware during the

installation process to help prevent damage to the product or vehicle.

Part Numbers

3025101 (brackets) 3025179 (boards) 3047902 (brackets & boards)

3015101 (brackets) 3015179 (boards) 3037902 (brackets & boards)

Product Photo

Powered Running Boards

(not included)

StandardFront

Standard

Middle

Standard

Standard Rear

Def tank

WARNING

Improper electrical installation may result in personal injury. Unless

you are familiar with the installation and handling of electrical systems,

have this step performed by someone who has that familiarity.

Torque Speciﬁcations

MET

M6 bolt 3 ft-lbs.

M8 bolt 7 ft-lbs.

SAE

5/16" bolt 7 ft-lbs.

7/16" bolt 20 ft-lbs.

Use above torque setting unless otherwise noted

Summary of content (13 pages)

PAGE 1
POWERED RUNNING BOARDS INSTALLATION MANUAL WARNING Level of Difficulty Improper electrical installation may result in personal injury. Unless you are familiar with the installation and handling of electrical systems, have this step performed by someone who has that familiarity.
PAGE 2
Bracket Location Diagram Standard Standard Middle Middle Def tank Def tank Def tank NEED ASSISTANCE? Standard Standard • 844.278.
PAGE 3
Step 1 Starting on the driver side, locate the five mounting locations underneath the vehicle. This installation will use the first, second, fourth and fifth mounting tabs. Note: Each bracket is specific to a mounting location. Refer to page 1 product image for correct locations. Step 2 Starting at the front driver-side mounting location, locate the threaded hole on the inside of the body panel and place an L-bracket on to that panel.
PAGE 4
Step 4 Locate the fifth mounting tab from step 1. Insert an M8 clip nut through the access hole and align it over the adjacent smaller hole. Place an L-bracket on to the body panel. Attach one standard mounting bracket to the L-bracket and vehicle using an M8 hex bolt, flat washer and lock washer. Attach the pinch weld with a 5/16" flat washer and nylock nut. Attach a step bracket using two 7/16" hex bolts, two 7/16" lock washers, two 7/16" flat washers and two 7/16" hex nuts.
PAGE 5
Step 7 Secure the running board to the front mounting bracket using one M8 flat washer and one 5/16" nylock nut on each T-rail stud. Repeat for the middle mounting bracket. Before securing the rear mounting bracket, place an LED light bracket over one of the T-rail studs, as shown in the third image. Secure each T-rail stud with one M8 flat washer and one 5/16" nylock nut. Snug the hardware, but do not fully tighten. Step 8 At this time, adjust the running board to the desired location.
PAGE 6
Step 9 On the front passenger-side mounting location, locate the threaded hole on the inside of the body panel and place an L-bracket on to that panel. Note: On models with def tanks you will not attach to the threaded hole on first mounting location. Attach one standard mounting bracket to the L-bracket and vehicle using an M8 hex bolt, flat washer and lock washer. Attach the pinch weld with a 5/16" flat washer and nylock nut.
PAGE 7
Step 11 Remove the fuse from the wiring harness before installing. Once the fuse is removed, take that section of the wiring harness and attach it to the battery. Route the opposite end of the harness through the firewall into the cab of the vehicle. Zip-tie the wiring harness in place once it is in the desired location. Step 12 Remove the front and rear door trim panels on both sides of the vehicle. Note: Remove any other vehicle components that could interfere with the wiring harness.
PAGE 8
Step 13 Wiring Locations Driver Once the trim panels are removed, take the second section of wiring harness and route it under the carpet, through the vehicle, from the passenger-side rear to the desired location. Passenger Refer to the diagrams below.
PAGE 9
Step 14 On the driver side, take the power wire and sensor wire (orange / yellow) and route it to the front of the vehicle underneath the carpet. If there is no plug in the floor behind the driver seat, skip to step 15. If there is a plug in the floor behind the driver seat continue this step. Take the driver-side rear actuator (red / black) and the LED light (brown / tan) and route it through the floor plug behind the driver seat.
PAGE 10
Step 17 Plug the door sensor into the wiring harness and route it up the door frame, under the carpet. Note: Depending on the vehicle, you may need to use the supplied sensor harness extensions for the two front door sensors. Once the harness and sensor are routed to the desired location, wipe the sensor and door with the provided alcohol wipe. Place two pieces of 1/2" x 1/2" double- sided tape on the sensor and attach the sensor to the vehicle. Repeat this process for the other three doors.
PAGE 11
Step 19 On the driver side, plug the rear actuator (red / black) into the running board and pull the extra wire back into the vehicle. Plug the LED light wire (brown / tan) into the LED light and secure it to the mounting bracket tab with the supplied jam nut. Once all the wiring is installed, cover the wires with slit loom for extra protection. Repeat for the passenger side of the vehicle. Refer to step 13 for wiring call out. Step 20 Locate a spot to install the power switch.
PAGE 12
Step 21 Once all wiring is installed, plug in the circuit board and place it underneath the carpet under the rear passenger seat. Attach the two wiring harnesses and re-install the fuse removed in step 11. Step 22 Congratulations on the installation of your new powered running boards. With the running boards installed, periodic inspections should be performed to ensure all mounting hardware remains tight.
PAGE 13
TROUBLESHOOTING & REGISTRATION Troubleshooting I just installed my steps and they are not coming down when I open the door. My switch is getting power, but the light stays on in both positions. Double check the connections. Check the fuse to make sure it is plugged in. Is the on / off switch getting power? Is the circuit board plugged in? Are the door sensors plugged in? The light is only supposed to be on when the system is turned on. If it is lit in both positions simply switch the red wires on the back.