Installation Guide

ManualsBrandsAries ManualsAutomotiveActionTrac 65-Inch Retractable Powered Running Boards, Select Jeep Wrangler JK

ARIESAUTOMOTIVE.COM

•

NEED ASSISTANCE?

•

844.278.4357

•

PAGE 1

INSTALLATION MANUAL

Parts List

1 Driver / left running board*

1 Passenger / right running board*

2 Mounting bracket, front

2 Mounting bracket, middle

2 Mounting bracket, rear

6 T-rails

12 Hex bolt, 1/4"

12 Flat washer, 1/4"

12 Nylock nut, 1/4"

12 Nylock nut, 5/16"

6 Hex bolt, M8 x 24.5mm

18 Flat washer, M8

6 Lock washer, M8

4 Door sensor

4 Magnet

2 Alcohol wipe

1 Power switch

1 Circuit board

1 Anti-seize

1 Wire loom

1 Wiring harness, two-piece

2 LED light

2 LED light bracket

4 Double-sided foam tape, 3/4" x 3/4"

8 Double-sided foam tape, 1/2" x 1/2"

* Running boards sold separately

Torque Speciﬁcations

Metric

M6 bolt 3 ft-lbs.

M8 bolt 7 ft-lbs.

M10 bolt 16 ft-lbs.

SAE

1/4" bolt 3 ft-lbs.

5/16" bolt 7 ft-lbs.

3/8" bolt 16 ft-lbs.

1/2" bolt 28 ft-lbs.

Use above torque setting unless otherwise noted

Tools Required

Ratchet Drill

Socket set Drill bit set

Zip ties Level

Level of Difﬁculty

Moderate

Notes and Maintenance

Before you begin installation, read all instructions thoroughly.

Proper tools will improve the quality of installation and reduce the time required.

No maintenance required on waterproof harness or water-resistant motors.

If mud or dirt is built up on the steps, simply spray them off and let them air dry.

Mild automotive detergent may be used to clean the product. Do not use dish detergent, abrasive

cleaners, abrasive pads, wire brushes or other similar products that may damage the ﬁnish.

Periodic inspection of all wires and connections should be

performed to ensure there is no visible damage or loose connections.

Refer to the last page of this manual for troubleshooting,

warranty and product registration information.

Refer to the table to the left when securing hardware during the

installation process to help prevent damage to the product or vehicle.

Part Numbers

3025170 (brackets) 3025165 (boards) 3036570 (brackets & boards)

Product Photo

ActionTrac

™

Powered Running Boards

(not included)

Front

Rear

Middle

WARNING

Improper electrical installation may result in personal injury. Unless

you are familiar with the installation and handling of electrical systems,

have this step performed by someone who has that familiarity.

Summary of content (10 pages)

PAGE 1
INSTALLATION MANUAL WARNING Level of Difficulty Improper electrical installation may result in personal injury. Unless you are familiar with the installation and handling of electrical systems, have this step performed by someone who has that familiarity.
PAGE 2
Step 1 Starting on the passenger side, locate the three mounting locations underneath the vehicle. Note: Each bracket is specific to a mounting location. Refer to page 1 product image for correct locations. Step 2 Starting at the front passenger-side mounting location, attach the mounting bracket through the two holes on the vehicle rocker panel using two 1/4" flat washers and 1/4" nylock nuts. Once the bracket is attached, mount one M8 bolt, M8 lock washer and M8 flat washer with anti-seize.
PAGE 3
Step 4 With the passenger-side brackets installed, take the passenger-side running board and insert three T-rails into the slot as shown. Note: Position each T-rail as close to the mounting bracket location as possible. Step 5 With help, carefully place the running board onto the mounting brackets. Align the T-rails with the mounting brackets on the vehicle. Slide the top mounting track on the board over the top flange on each bracket.
PAGE 4
Step 7 At this time, adjust the running board to the desired location. With the running board in position, it is recommended to tighten all brackets to the vehicle first, followed by the running board connections. Repeat steps 1 through 7 on the driver side. Step 8 Remove the fuse from the wiring harness before installing. Once the fuse is removed, take that section of the wiring harness and attach it to the battery. Route the opposite end of the harness through the firewall into the cab of the vehicle.
PAGE 5
Step 9 Remove the fasteners securing the front and rear door trim panels on both sides of the vehicle. There are five clips on each side of the vehicle securing the trim panels, three for the front and two for the rear. Note: It may be easier to move the seats all the way back when removing the front trim panel and all the way forward when removing the rear trim panel.
PAGE 6
Step 11 On the driver side, take the power wire and sensor wire (orange / yellow) and route it to the front of the vehicle underneath the carpet. Take the driver-side rear actuator (red / black) and the LED light (brown / tan) and route it through the floor plug behind the driver seat. Step 12 On the passenger side, take the sensor wire (gray / green) and route it to the front of the vehicle underneath the carpet.
PAGE 7
Step 14 Plug the door sensor into the wiring harness and route it up the door frame, under the carpet. Note: If installing a door delete switch, refer to part #3020000-INS at this time. Once the harness and sensor are routed to the desired location, wipe the sensor and door with the provided alcohol wipe. Place two pieces of 1/2" x 1/2" double- sided tape on the sensor and attach the sensor to the vehicle. Repeat this process for the other three doors.
PAGE 8
Step 16 On the driver side, plug the rear actuator (red / black) into the running board and pull the extra wire back into the vehicle. Plug the LED light wire (brown / tan) into the LED light and secure it to the mounting bracket tab with the supplied jam nut. Once all the wiring is installed, cover the wires with slit loom for extra protection. Repeat for the passenger side of the vehicle. Refer to step 12 for wiring call out. Step 17 Locate a spot to install the power switch.
PAGE 9
Step 18 Once all wiring is installed, plug in the circuit board and place it underneath the carpet under the rear passenger seat. Attach the two wiring harnesses and re-install the fuse removed in step 8. Step 19 Congratulations on the installation of your new ActionTrac ™ powered running boards. With the running boards installed, periodic inspections should be performed to ensure all mounting hardware remains tight.
PAGE 10
TROUBLESHOOTING & REGISTRATION Troubleshooting I just installed my steps and they are not coming down when I open the door. My switch is getting power, but the light stays on in both positions. Everything is plugged in and the switch is turning on and off, but the steps still won't deploy. I tested the motor, and it works. I checked the sensors individually, and the system still won't work. The steps don't deploy unless I do it manually with 12V power.