INSTALLATION INSTRUCTIONS GRILLE GUARD 07-15 TOYOTA TUNDRA 08-15 TOYOTA SEQUOIA PART # 2067/2067-2
GRILLE GUARD 07-14 TOYOTA TUNDRA, 08-14 SEQUOIA PARTS LIST: 1 Grille Guard 2 1 1 1 1 1 1 4 4 4 Driver/left Frame Mounting Bracket Passenger/right Frame Mounting Bracket Driver/left Top Frame Bracket Passenger/right Top Frame Bracket Driver/left Top Bracket Passenger/right Top Bracket 12-1.75mm x 35mm Hex Bolts 12mm x 32mm OD x 3mm Flat Washers 12mm Lock Washers 4 2 4 4 4 4 4 2 10mm Cam Lever Quick Release Bolts with Special Pivot Washer 10mm x 24mm OD x 2.2mm Flat Washers 10-1.
GRILLE GUARD 07-14 TOYOTA TUNDRA, 08-14 SEQUOIA from below, remove the hardware attaching the bumper cover to the cross member to access the end of the frame and bracket, (Figure 2). 4. Select the passenger side Top Frame Bracket, (Figure 3A). Remove the top (2) factory hex nuts on the outside and the single hex nut on the inside attaching the factory bumper bracket to the end of the frame on the passenger side, (Figure 3B). 5.
GRILLE GUARD 07-14 TOYOTA TUNDRA, 08-14 SEQUOIA 20. Slowly close the hood and check for clearance. Release both Quick Release bolts. Push the Grille Guard into the "closed" position. If needed, loosen the upper bolt on each Frame Mounting Bracket, (Figure 16). WARNING! Do not completely loosen bolts or damage to the truck or Grille Guard may occur. 21. Push the Grille Guard back towards the vehicle and fully tighten all hardware, (Figure 17 & 18).
GRILLE GUARD 07-14 TOYOTA TUNDRA, 08-14 SEQUOIA Passenger/right Side Installation Pictured Remove (2) top factory hex nuts on outside of bumper bracket Front Remove (1) factory hex nut on inside of bracket Passenger side top bracket Front (Fig 3B) Passenger side Top Bracket pictured installed over bumper bracket. Pictured from below (Fig 4) Reuse factory hex nuts to secure Top Bracket to end of frame.
GRILLE GUARD 07-14 TOYOTA TUNDRA, 08-14 SEQUOIA Passenger/right Side Installation Pictured Front (Fig 7) The heavy duty factory tow hooks cannot be reinstalled. (Fig 8A) Passenger side Frame Mounting Bracket Front Front (Fig 8B) Install Frame Bracket with factory tow hook bolts.
GRILLE GUARD 07-14 TOYOTA TUNDRA, 08-14 SEQUOIA Passenger/right Side Installation Pictured Attach Top Bracket to Frame Bracket with: (2) 8mm x 25mm Hex Bolts (2) 8mm Lock Washers (2) 8mm Flat Washers Front Front (Fig 10A) Passenger side Top Bracket and Top Frame Bracket illustrated (2) 8mm x 25mm Hex Bolts (2) 8mm Lock Washers (2) 8mm Flat Washers Insert (1) 12mm Hex Bolt and Washers per side then rotate Grille Guard up and in position (Fig 10B) Driver side 07-13 pictured from above Front Fig 11 Fro
GRILLE GUARD 07-14 TOYOTA TUNDRA, 08-14 SEQUOIA Passenger/right Side Installation Pictured Grille Guard upright (2) 10mm Plastic Washers 10mm Flat Washer 10mm Nylon Lock Nut Insert a 10mm Plastic Washer between the Grille Guard and the Top Bracket and under the Flat Washer on each Quick Release Bolt.
GRILLE GUARD 07-14 TOYOTA TUNDRA, 08-14 SEQUOIA Passenger/right Side Installation Pictured Quick Release in "closed" position Push Grille Guard back to the "closed" position Front Fig 17 Fig 18 Opening and closing the hood-required for 2007-13 models only 23. Lift the levers on the Quick Release bolt to release the clamping pressure, (Figure 14). Pull the Grille Guard out and away from the vehicle to the "open" position, (Figure 15).
