Precision Edge Owner/Operator Manual Manuel Du Propriétaire/Utilisateur Model 986101 – Edger ENGLISH FRANÇAIS 03818800B 2/09 Printed in USA
TABLE OF CONTENTS SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . 4 STORAGE . . . . . . . . . . . . . . . . . . . . . . 15 ASSEMBLY. . . . . . . . . . . . . . . . . . . . . . . 7 TROUBLESHOOTING . . . . . . . . . . . . . 16 CONTROLS AND FEATURES . . . . . . . . 8 SERVICE PARTS . . . . . . . . . . . . . . . . . 16 OPERATION . . . . . . . . . . . . . . . . . . . . . . 9 SPECIFICATIONS . . . . . . . . . . . . . . . . 17 MAINTENANCE SCHEDULE . . . . . . . . 13 WARRANTY . . . . . . . . . . . .
PRODUCT REGISTRATION The Ariens dealer must register the product at the time of purchase. Registering the product will help the company process warranty claims or contact you with the latest service information. All claims meeting requirements during the limited warranty period will be honored, whether or not the product registration card is returned. Keep a proof of purchase if you do not register your unit.
Before Attempting To Operate Your Unit: 1. Make sure all assembly has been properly completed. 2. Understand all Safety Precautions provided in the manuals. 3. Review control functions and operation of the unit. Do not operate the unit unless all controls function as described in this manual. 4. Review recommended lubrication, maintenance and adjustments. 5. Review Limited Warranty Policy. 6. Fill out a product registration card and return the card to the Ariens Company or go to www.ariens.com.
SAFETY DECALS AND LOCATIONS ALWAYS replace missing or damaged Safety Decals. Refer to figure 2 for Safety Decal locations. 1 Always keep feet away from rotating parts. Emission Control System Certification Label Tampering with emission controls and components by unauthorized personnel may result in severe fines or penalties. Emission controls and components can only be adjusted by EPA and/or CARB authorized service centers.
Do not tilt when starting the engine or switching on the motor, unless the edger has to be tilted for starting. In this case, do not tilt it more than absolutely necessary and lift only the part which is away from the operator. Do not start the engine when a bystander is standing in front of the blade(s). Do not put hands or feet near or under rotating parts.
ASSEMBLY WARNING: AVOID INJURY. Read and understand the entire Safety section before proceeding. Check Engine Oil 1. Fill engine crankcase with oil. See engine manual. Check Engine Fuel 1. Fill fuel tank. See Check Engine Fuel on page 7. Tools Required • 1/2" Wrench • Needle Nose Pliers Check Safety Interlock System WARNING: Safety interlock failure and improper operation of unit can result in death or serious injury. Check system before each use to make sure it is functioning properly.
CONTROLS AND FEATURES 1 2 3 13 11 12 11 4 5 10 9 8 6 7 Figure 4 1. Operator Presence Control 2. Cutting Depth Adjuster 3. Cutting Angle Adjuster 4. Blade 5. Oil Fill/Dipstick 6. Front Wheel Adjuster 7. Oil Drain Plug 8. Engine Shut Off Switch 9. Recoil Starter 10. Fuel Shut Off 11. Rear Wheel Height Adjuster 12. Choke 13.
OPERATION Cutting Depth Adjuster WARNING: AVOID INJURY. Read and understand the entire Safety section before proceeding. Controls how deeply the blade cuts into grass. 1. Pull the lever slightly to disengage the lock pin from the bracket and then pull the lever back to raise the cutting head and cut a shallower groove. 2. Pull the lever slightly to disengage the lock pin from the bracket and then push the lever forward to lower the head and cut more deeply.
Cutting Angle Adjuster Rear Wheel Height Adjuster Controls the cutting angle of the blade for decorative edging. 1. Push the lever forward to unlock the head and then rotate it left or right to set the desired edging angle. NOTE: The head pivots from about 70 degrees to 180 degrees. IMPORTANT: Make sure the front wheel does not contact the blade when angling the blade for a beveled edge. Sets the rear wheel height to support the edger when working along curbs or other uneven terrain. 1.
Front Wheel Adjuster Engine Controls Positions the front wheel on the axle to balance the unit when working along curbs or other uneven terrain. NOTE: Make sure the front wheel rolls on the work surface. IMPORTANT: Make sure the cutting blade will not contact wheel before starting the engine. 1. With the engine shut off, remove the pin from the axle and position the front wheel on the right or left side of the axle as needed, and secure in position with the hair pin.
Oil Drain Plug Oil drain plug provides a convenient location to drain oil. 1. Place a pan under the opening in the unit frame, remove the plug, remove the oil fill cap/dipstick and allow the oil to drain completely. 2. Replace the plug and then fill engine with appropriate engine oil for your conditions. See Engine Manual for types of oil and operating ranges. Do not overfill. Oil Drain Plug STARTING AND SHUTTING OFF ENGINE Shutting Off the Engine 1. Stop unit. 2. Disengage blade. 3.
TRANSPORTING UNIT FOR BEST PERFORMANCE ALWAYS shut off engine, and close fuel shutoff valve or drain fuel when transporting unit on a truck or trailer. Tie unit down securely. Do not tie down by linkages, guards, cables or other parts that may be damaged. Whenever possible keep the wheels on a hard, flat surface. Edge thawed ground. Frozen or rocky ground can damage blade. Dry, hard surfaces will raise a lot of dust. When possible edge ground that is moist but not muddy or saturated.
SERVICE AND ADJUSTMENTS WARNING: AVOID INJURY. Read and understand the entire Safety section before proceeding. Blade Change WARNING: Blades are sharp and can cut you. Wear sturdy gloves warning 1. Stop engine, wait for all moving parts to stop and hot parts to cool. Make sure the engine shut off switch is in the off position. 2. Block the blade with a wooden block. 3. Remove the mounting hardware and blade from the unit. 4.
Oil Change 2. Place an appropriate pan under the oil drain opening, and remove oil drain plug from engine. 3. After all oil has drained, replace the drain plug. 4. Fill engine with appropriate engine oil for your conditions. See Engine Manual for types of oil and operating ranges. Do not overfill. NOTE: Follow instructions provided in the engine owner’s manual. 1. Stop engine, wait for all moving parts to stop and hot parts to cool. Make sure the engine shut off switch is in the off position.
TROUBLESHOOTING PROBLEM Engine Won’t Start PROBABLE CAUSE 1. Engine start switch turned off. 2. Fuel tank empty. 3. Blade engaged. Blade Won’t Rotate CORRECTION 1. Turn switch on. See Starting the Engine on page 12. 2. Fill engine with appropriate fuel. See engine owner’s manual for fuel type and capacity. 3. The cutting depth adjuster is out of the neutral position. See Cutting Depth Adjuster on page 9. 1. Loose or damaged belt. 2. Seized bearings. 3. Sliding shaft seized. 1. Replace belt.
SPECIFICATIONS Model 986101 Description Engine Edger Subaru OHC SP170 10 (169) Displacement - in3 (cc) Fuel Capacity - gal. (L) Engine Oil - oz. (L) .90 (3.4) 20 (0.60) See Engine Manual for Type Blade 9" Blade Cutting Positions 4 Cutting Angle 70 - 180 degrees Length- in. (cm) 44.75 (113.7) Width- in. (cm) 19.75 (50.2) Height - in. (cm) 38.0 (96.5) Weight - lbs (kg) 72.0 (32.
Two-Year Limited Lawn and Garden Walk Behind Warranty This warranty statement applies only to 21-Inch Walk Behind Lawn Mowers, Wide Area Walks, Super Striper Mowers, Tillers, String Trimmers, Log Splitters, Edgers and Power Brushes Ariens Company (Ariens) warrants to the original purchaser that Ariens and Gravely brand consumer products manufactured and sold by Ariens after December 31, 2007 will be free from defects in material and workmanship for a period of two years after the date of purchase.
Exclusions – Items Not Covered by This Warranty • • • • • Engines and engine accessories are covered only by the engine manufacturer’s warranty and are not covered by this warranty. Parts that are not genuine Ariens or Gravely service parts are not covered by this warranty.
Ariens Company 655 West Ryan Street Brillion, WI 54110-1072 920-756-2141 Fax 920-756-2407 www.ariens.
