Aria By C H A N N EL VI S I O N TM Flush Mount Amplifier Spkrs Active Loc al In IR In 24VDC A0350 Flush Mount Amplifier 10
The A0350 Flush Mount Amplifier can be used with Channel Vision’s CAT5 audio hubs to provide a powerful 50Watts per channel in the listening zone. Alternatively, the A0350 can be added to the SP525, SP650, and SP800 Free Standing Speakers to create a high-quality amplified speaker system.
Rear Panel Features and Connections: Left & Right Audio Trim Pots... Control the maximum output level of the amplifier. If audio input level is quiet, the trim pots will have little noticeable effect. A0350 Aria By C H A N N E L V I S ION TM Flush Mount Amplifier Spkrs Active Local In IR In 24VDC Volume Jumper... Set J6 to pins 1&2 to select default power up volume. Set J6 to pins 2&3 to select previous volume level on power up.
IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions for future reference. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this device near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with these instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
Accessories & Complementary Products (sold separately) Vid 1 Vol + Vid 2 Vid 3 Vol - Vid 4 Pwr Mute C HANNEL V ISION TM POWER MODEL A0501 1 S O U R C E 2 3 4 ZONE POWER MUTE A0127 ... IR repeating keypad. The A0127 contains the IR codes to operate the volume controls in the Amplified Wireless Audio Receiver. You may also use a standard IR receiver or a 3rd party keypad.
A0350 Installation The A0350 can be installed in the wall using a standard 2-gang junction box or low-voltage mounting ring. The Flush Mount Amplifier can also be installed into the back of Channel Vision’s SP525, SP650, or SP800 Free Standing Speakers.
Using the A0350 Behind a TV The A0350 can be flush-mounted behind a wall-mounted TV to power in-wall speakers. By connecting the audio outputs from the TV to the RCA inputs of the A0350, the TV’s audio signal will be amplified to the in-wall speakers. If the TV has variable audio outputs, the sound level will simply be controlled by the TV’s volume buttons.
Using the A0350 in a Stand-alone System The A0350 can be flush-mounted in a room to power in-wall speakers. By connecting the audio outputs from an audio source to the RCA inputs of the A0350, the audio signal will be amplified to the in-wall speakers. Most audio sources only offer a fixed audio output, A0350 volume level can be adjusted by using an A0127 keypad or by connecting an IR-2400 and using a compatible remote such as model A0505.
Using the A0350 with a CAT5 Audio Hub The A0350 can accept the signal from one Channel Vision’s CAT5 Audio Hubs, such as the P-2044. Audio and IR signals are transmitted through the CAT5 cable, while power is connected directly to the front of the A0350. Alternatively, power can be connected via a pair of 16AWG wires to the power screw terminals on the back side of the A0350.
Using the A0350 with a CAT5 Audio Hub - Alternate Setup The A0350 can accept the signal from one Channel Vision’s CAT5 Audio Hubs, such as the P-2044. An A0125 keypad can be wired in the CAT5 line along with other input modules to accommodate a more traditional CAT5 Audio wiring scheme. If an additional 2-conductor 16 AWG wire is run between the A0350 and main equipment location, the A0350 power supply can be remotely located and connected via the rear-panel screw terminals.
Troubleshooting: Problem: Hum in System Troubleshooting: Plug all parts of the system into the same outlet to see if the hum goes away. Try lifting the ground with a ground lifting plug. Cause: The different components in the system are connected to different electrical grounds. This forces electrical currents to find alternate paths to ground causing an audible 60Hz hum. Solution: Plug products into an electrical circuit with a common ground. Problem: CAT5 Audio input is not working.
1 Channel Vision Technology will repair or replace any defect in material or workmanship which occurs during normal use of this product with new or rebuilt parts, free of charge in the USA, for one year from the date of original purchase. This is a no hassle warranty with no mail in warranty card needed. This warranty does not cover damages in shipment, failures caused by other products not supplied by Channel Vision Technology, or failures due to accident, misuse, abuse, or alteration of the equipment.
