Nova™ Microcinerator Operating Instructions Consignes d' utilisation Instrucciones de operaciones Bedienungsanleitung S3010 - 100V S3011 - 120V S3022 - 220V S3024 - 240V © 2005 Argos Technologies Inc. www.argos-tech.com Argos Technologies, Inc.
Contents Page Subject 2 3 4 5 5 6 7 8 9 10 11 12-13 14 15-16 Product Description and Environmental Conditions Materials and Specifications Symbols Used Warranty Information Getting Started Part Descriptions Sterilizing Loops and Needles Tilting the Burner Head Maintenance, Care & Safety Precautions Trouble Shooting Replacement Parts Ordering Information Accessories Repair Service Replacing the Sterilizing Element Product Description Thank you for purchasing the Nova™ Microcinerator.
Materials and Specification Voltages Part No S3010 Part No S3011 Part No S3022 Part No S3024 - 100V, 50 HZ, 235W, 2.3 amps – 120V, 60 HZ, 200W, 1.6 amps – 220V, 50 HZ, 200W, .94 amps – 240 V, 50 HZ,200W, .83 amps Dimensions: Packed: 300x300x200, 2.3kilos Unpacked 240(max)x200x180, 1.2kilos Ceramic Element Insulation Colour: Basic Composition: Recommended Use Limit: Melting Point: Typical Dry Density: Specific Heat Capacity at 1093˚C (2000˚F): Tensile Strength – 6.
Symbols Used Easily touched high temperature parts T A Time Lag Fuse Amperes Protective Conductor Terminal IMPORTANT: If this product is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired. All personnel who operate and maintain the equipment are trained in its operation and safe use.
WARRANTY INFORMATION The Nova™ Microcinerator is guaranteed free from defects in workmanship and materials for a period of one year after the customer receives the product. This DOES NOT include the Sterilizing Element, which is guaranteed for six months. In order to qualify for warranty repair, the customer must return the warranty card supplied with the unit that includes all of the information required to validate proof of purchase.
Part Descriptions © Argos Technologies Inc 2005 Note: to ensure optimum performance your Nova™ Microcinerator should be left on all day. During periods of prolonged non-use however, the unit should be turned off to extend the life of the heating element.
Sterilizing Loops and Needles 1. 2. 3. Carefully insert the loop or needle at least halfway into the sterilizing element to avoid aerosoling any residual contaminants. Take care not to scrape the element walls as this may reduce the efficiency of the heating unit. The loop or needle will be sterilized in 5 to 7 seconds. Heating your loop or needle until it glows is not necessary. Loops when not in use can be placed in the loop storage holes located in the legs of the base unit.
Tilting the Burner Head The burner head angle can be altered to suit your working style. Allow the burner to cool for 1 hour before adjusting. Turn the burner tilt adjustment lever counter clockwise approximately ½ turn as shown and tilt the burner head to the desired position. © Argos Technologies Inc 2005 To lock the burner head, turn the burner tilt adjustment lever clockwise until the head is secure. Caution, do not over tighten the burner adjustment lever.
Maintenance, Care & Safety Precautions WARNING!! The Nova™ Microcinerator should never be submerged in water or any other cleaning compounds. To clean use a damp cloth only and avoid introducing any fluids into the unit. As with any electrical instrument, it is important not to allow any liquid to enter the Nova™ Microcinerator. Doing so may cause damage to the electrical components, electrical shocks to the user or create a fire hazard.
Trouble Shooting Switch not illuminated – Check Fuse and replace if required. Burner not heating – If the burner is not heating and glowing red and the switch is illuminated the burner element may need to be replaced. Check the number in the Replacement Parts section and order from your vendor. Note that only qualified personnel should perform repairs. Note that there are no user serviceable parts inside of the unit.
Replacement Parts Ordering Information Replacement parts should be ordered from your local distributor Nova™ Microcinerator Part No. S3010 S3011 S3022 S3024 S3010A S3011A S3022A S3010H S3011H S3022H S3024H S3012 S3013 Description 100V Nova™ Microcinerator 120V Nova™ Microcinerator 220V Nova™ Microcinerator 240V Nova™ Microcinerator Replacement Fuse 3.15 Amp – Asia Replacement Fuse 2.
Accessories 3 Place Slide Dryer – Part Number S3012. Use the heat already generated by your sterilizer to dry your slides. Aluminium Loop Rest – Part Number S3013. Guides the loop into the optimum sterilizing position and protects your loop handles from overheating and melting.
The Slide Dryer and Loop Rest can be used together.
Repair Service Should your Nova™ Microcinerator require service or repair, please contact Argos Technologies customer service. They will issue a Return Authorization Number and advise on the proper packaging and method of shipment. Customer Service: in US: 800-886-8675 outside US: 847-783-0456 Argos Technologies, Inc. 1551 Scottsdale Court Suite 200 Elgin IL 60123 Attn: Technical Service Be sure to list your RA number on the shipping label.
Replacing the Sterilizing Element Important – Only qualified personnel should carry out repairs to this product. Always switch the unit “off” and disconnect from the power source and allow to cool for 1 hour before carrying out any repairs, cleaning or maintenance.
Tools required: • • 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. Cross headed (Philips) screwdriver 7mm AF (9/32” AF) spanner or socket wrench Remove screws (1). Remove front face (2). Remove the suction feet screws (7) and suction feet (6). Remove screw (8). The base plate (5) can now be removed. Disconnect the sterilizing element (3) wires from the on/off switch (12). Note the connections.
