Premium 4 Burner Gas BBQ Assembly Instructions - Please keep for future reference 450/9411 464/6549 Dimensions Width - 123.5cm Depth - 56.7cm Height - 107.5cm Important - Please read this instructions fully before using the appliance If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800. Please visit the website www.argos.co.uk for more information.
Safety and Care Advice Important - Please read this instructions fully before using the appliance • • • • • • • • • • • • • • • • • • • • • • • • • • • • • Assembly time: approx. 45 mins. Retain these instructions for future reference. This product is for outdoor use only. Do not use indoors. Do not use the barbecue or store gas bottles below ground level. LP gas is heavier than air so if a leak occurs the gas will collect at a low level and could ignite in the presence of a flame or spark.
Safety and Care Advice The maximum dimension of the gas bottle is dia 31.5cm and height 58cm. 2 Key 1= maximum diameter 2= maximum height 1 Never mount the gas bottle under the barbecue on the base shelf as this could result in serious injury to the user, other people and/or property. Always place the gas bottle at the left or right hand side of the appliance. The gas bottle should be sited as far away from the appliance as possible without straining the hose.
Safety and Care Advice Operation Warning • Before proceeding, make certain that you understand the IMPORTANT INFORMATION section of this manual. • Your barbecue is not designed to be used with more than 50% of the cooking area as a solid plate — this includes baking dishes. Full coverage will cause excessive build-up of heat and damage the barbecue. This is not covered by warranty.
Safety and Care Advice • • Push in and turn the control knob anti-clockwise until you feel resistance pause 4 seconds. Then continue turning the control knob until a click is heard and the burner is lit. If the burner fails to ignite after above procedure, turn the knob to the OFF position and close the gas valve. Wait 5 minutes and then repeat the above steps. If the barbecue still fails to light, please refer to the manual ignition instruction in the section below.
Safety and Care Advice When flare-ups do occur, they can usually be extinguished by applying baking soda or salt directly onto the flame tamer. Always protect your hands when handling anything near the cooking surface of the barbecue and take care to protect yourself from the flames. If a fat fire occurs, please see the instructions given below. Fat Fires Empty and clean the drip tray, of food debris after each cooking session.
Safety and Care Advice Cooking Surfaces & Warming Rack When the barbecue has cooled, clean with hot soapy water. To remove any food residue, use a mild cream cleaner on a non-abrasive pad. Do not use scouring pads or powders as they can permanently damage the finish. Rinse well and dry thoroughly. Due to the weight of the cooking surfaces, we do not recommend cleaning in a dishwasher. It is quite normal for surface rust to be present on the cooking surface.
Safety and Care Advice Barbecue Hood or Lid Use a non-abrasive cloth or pad and clean with hot, soapy water. Do not use scouring pads or powders as they can permanently damage the finish. Trolley Wipe with a cloth wrung out in hot soapy water and dry. Fixings All screws and bolts, etc. should be checked and tightened on a regular basis. Storage Ensure the barbecue is properly cooled before covering or storing. Store your barbecue in a cool dry place.
Components - Parts If you have damaged or missing components, call the Customer Helpline: 03456 400800 Please check you have all the panels listed below 1 Grill Assembly x 1 4 Heat tent x 4 7 Side table assembly x 1 10 Side table panel x 1 2 Warming rack x 1 3 5 Grease cup x 1 6 8 Side burner knob x 1 11 Side burner panel x 1 Cooking grill x 2 Side burner grate x 1 (included in side burner assembly) 9 Side burner assembly x 1 12 Cart rear support x 1 8
Components - Parts Please check you have all the panels listed below 13 Left cart assembly x 1 16 Front panel x 1 17 Condiment compartment x 1 19 20 Wheel x 2 Axle x 1 22 Leg cap x 2 9 14 Right cart assembly x 1 23 Side burner electrode wire x 1 15 Bottom shelf assembly x 1 18 Condiment rail x 1 21 Wheel cap x 2
Components - Fittings Please check you have all the panels listed below Note: The quantities below are the correct amount to complete the assembly.
Assembly Instructions Step 1 Put the cart left cart assembly 13 on the bottom shelf assembly 15 using 35mm bolts B . Check the orientation of the panel assembly and fix the bolts tightly by the screwdriver. 13 B 15 B B FRONT Step 2 Put the cart right cart assembly 14 on the bottom shelf assembly 15 using 35mm bolts B . Check the orientation of all panel assemblies and fix the bolts tightly by the screwdriver.
Assembly Instructions Step 3 Fix the front panel 16 between the front leg of the left cart assembly 13 and the front leg of the right cart assembly 14 using 12mm bolts A . FRONT 14 A 13 A 16 A A Step 4 Fix the Condiment compartment 17 between the front leg of the left cart assembly 13 and the front leg of the right cart assembly 14 using 12mm bolts A and M6 nut E .
Assembly Instructions Step 5 21 Apply the wheels 20 to the front leg and the rear leg of the right cart assembly 14 using the axle 19 . D 19 20 Then fix the axle 24 by the axle nuts D and cover the wheels 20 by the wheel caps 21 . D 20 21 14 FRONT Step 6 B Apply the leg caps 22 to the front leg and rear leg of the left cart assembly 13 . Secure them by using 35mm bolts B . B 22 Fix the bolts tightly by the screwdriver.
Assembly Instructions Step 7 FRONT Fix the cart rear support 12 on the rear leg of the left cart assembly 13 and the rear leg of the right cart assembly 14 using 12mm bolts A . A A A Do not tighten the bolts at this stage. A 12 13 14 Step 8 Insert condiment rail 18 from the left of the left front leg 13 . Cover the insert hole with plastic cap F .
Assembly Instructions Step 9 Set the grill assembly 1 onto the left cart assembly 13 and the right cart assembly 14 using 35mm bolts B . 1 Secure all the bolts of step 7 and step 9 tightly by the screwdriver. B B 13 B B 14 Step 10 FRONT a: Screw 4pcs of 12mm bolts A onto the left side of the grill assembly 1 . a: Have half of the bolt threads go into the bolt holes. Do not tighten at this stage. b: Align the 12mm bolts A properly with the side table assembly 7 .
Assembly Instructions Step 11 1 a: a: Screw 4pcs of 12mm bolts A onto the right side of the grill assembly 1 . Have half of the bolt threads go into the bolt holes. Do not tighten at this stage. b: Align the 12mm bolts A A A A A b: properly with the side burner assembly 9 . 9 A Fix the bolts tightly by the screwdriver after the alignment is done. A A A Step 12 a: Fix the 10mm bolt the side table panel Note: Do not tighten the bolts. 10 C on a: .
Assembly Instructions Step 13 a: Fix the 10mm bolt C the side burner panel Note: Do not tighten the bolts. 11 on . b: Hang the side burner panel 11 on the side burner assembly 9 . a: 11 C b: Slide the 10mm bolt C leftwards until the panel is fixed on the side burner assembly 9 . c: Fix the side burner panel 9 C 11 c: 9 11 on the main control panel of the grill assembly 1 using 10mm bolts C .
Assembly Instructions Step 14 c: Fix the side burner valve on the side burner panel 11 using those two screws loosen on procedure 14a. d: Align the side burner venturi against the valve. c: 11 d: Important: Make sure the valve tip goes into the burner venturi completely with good alignment. Then tighten those two screws on the side burner after the alignment. e: Install the side burner electrode wire 23 to the side burner electrode and the igniter.
Assembly Instructions Step 15 Put the side burner knob on the side burner panel 8 11 . 8 11 Step 16 Put the side burner grate 6 on the side burner assembly 9 and align with the holes.
Assembly Instructions Step 17 2 Put the heat tent 4 , cooking grill 3 and warming rack 2 on the grill assembly 1 . 3 4 1 Step 18 Put the grease cup 5 at the bottom of the grill assembly 1 .
Assembly Instructions Step 19 Assembly is complete. ALL JOINTS AND CONNECTIONS MUST NOW BE LEAK TESTED BEFORE USING THE BARBECUE. Leak test annually, and whenever the gas bottle is removed or replaced. Always place the gas bottle at the side of the appliance. The gas bottle should be sited as far away from the appliance as possible without straining the hose. The hose length should not exceed 1.5 metres.
Technical Specification Model Number KS15048 Gas Category I3+(28-30/37) Type of Gas Propane Gas Pressure 37 mbar Pin Number Butane 28-30 mbar 1008/CP/2791 Injector Size (Main Burner) 0.86mm Injector Size (Side Burner) 0.94mm Total Heat Input 15.22 kW 4 Burner Heat Input 11.72 kW Side Burner Heat Input 3.5 kW Gas Consumption 1085 g/h Country of Destination GB and IE Do not use this barbecue outside Great Britain and Ireland.
Troubleshooting Problem Burner will not light using the ignition system Possible Cause Solution LP gas cylinder is empty Replace with full cylinder Faulty regulator Have regulator checked or replace Obstructions in burner Clean burner Obstructions in gas jets or gas hose Clean jets and gas hose Electrode wire is loose or disconnected Reconnect wire on electrode or ignition unit.
