4 Burner Gas BBQ with side burner Assembly Instructions - Please keep for future reference 345/1663 Dimensions Width - 130cm Depth - 55.5cm Height - 97cm Important - Please read this instructions fully before starting assembly If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800.
Safety and Care Advice Important - Please read this instructions fully before starting assembly • • • • • • • • • • • • • • • • • • • • • Assembly time: approx. 45 mins. Retain these instructions for future reference. For outdoors use only – do not use indoors. Do not use below ground level and confined spaces. For use with LPG bottled gas only. A regulator of 37mbar must be used for propane. Do not use within 1m of any flammable structure or surface.
Safety and Care Advice or tension. The hose should hang freely with no bends, folds, or kinks that could obstruct free flow of gas. Apart from the connection point, no part of the hose should touch any hot barbecue parts. Always inspect the hose for cuts, cracks, or excessive wear before use. If the hose is damaged, it must be replaced with hose suitable for use with LPG and meet the national standards for the country of use. The length of the hose shall not exceed 1.5m. N.B.-The date on U.K.
Safety and Care Advice Manual Ignition Instruction for Main Burner • Insert lit match through the match-lighting hole at the side or bottom of the barbecue body. • Push in and turn the control knob anti-clockwise to the max position, the left hand centre burner should ignite. • After the left hand centre burner is lit, push and turn the leftmost control knob to max position, the second burner should ignite automatically. • Repeat same procedure to light the right hand centre and the rightmost burner.
Safety and Care Advice Care and Maintenance Regularly clean your barbecue between uses and especially after extended periods of storage. Ensure the barbecue and its components are sufficiently cool before cleaning. Do not leave the barbecue exposed to outside weather conditions or stored in damp, moist areas. • Never douse the barbecue with water when its surfaces are hot. • Never handle hot parts with unprotected hands. Cooking Grill Clean with hot soapy water.
Safety and Care Advice Fixings All screws and bolts, etc. should be checked and tightened on a regular basis. Storage Store your barbecue in a cool dry place. It must be inspected on a regular basis as damp or condensation can form which may result in damage to the barbecue. It may be necessary to dry the barbecue and the inside of the cover if used. Mould can grow under these conditions and should be cleaned and treated if required.
Components - Parts If you have damaged or missing components, call the Customer Helpline: 08456 400800.
Components - Parts Please check you have all the panels listed below 13 Wheel x 2 16 Front canvas x1 19 Side table front support x1 22 Side burner knob x 1 7 14 upper support x 2 15 Control panel assembly x 1 18 Side table x1 17 Bottom shelf x1 20 Side table rear support x1 23 Side burner electrode x 1 21 Side burner assembly x1 24 Side burner x 1 25 Side burner grate x1
Components - Fittings Please check you have all the panels listed below Note: The quantities below are the correct amount to complete the assembly.
Assembly Instructions Step 1 Put the left front leg 11 and left rear leg 12 on the bottom shelf 17 using 10mm bolts B . 12 Fix the bolts tightly by the screwdriver. 11 17 B B FRONT Step 2 Put the right front leg 9 and right rear leg 10 on the bottom shelf 17 using 10mm bolts B . Fix the bolts tightly by the screwdriver.
Assembly Instructions Step 3 Fix the leg caps 8 to the right front leg 9 and right rear leg 10 . 10 Hammer the leg caps 8 slightly to make it fix on the legs. 9 8 FRONT 8 Step 4 Insert the wheels 13 to the left front leg 11 and the left rear leg 12 using the axles G . 12 11 Then fix the axles G by Rpin F .
Assembly Instructions Step 5 14 14 Connect the upper support 14 with the left front leg 11 and left rear leg 12 using 25mm bolts A and M6 nuts C . C A C C A C Repeat the same connection of the upper support 14 with the right front leg 9 and right rear leg 10 using 25mm bolts B and M6 nuts C . A 12 11 A 10 9 Fix the bolts tightly by the screwdriver. FRONT Step 6 Fix the control panel assembly 15 on the upper supports 14 using 40mm bolts D .
Assembly Instructions Step 7 a: Fix the 25mm bolts A on the grill and M6 nuts assembly 1 . C a: A C A C 1 A C A b: Set the grill assembly C 1 on the upper supports 14 and fix it by 40mm bolts D and M6 nuts C . b: (Do not tighten the bolts at this stage.) Align all valves on the control panel assembly 15 against each venturi of the burner. C C C 1 Important: Make sure the valve tip goes into the venturi tube completely with good alignment.
Assembly Instructions Step 8 Put the grease cup hanger 6 through the hole of the the grill assembly 1 . 6 Hang the grease cup 7 on the grease cup hanger 6 . 1 6 7 Step 9 Place the heat tent 5 on top of each burner of the grill assembly 1 . Align the heat tent 5 with tabs on its end against slots on the firebowl back. 5 1 Rest the heat tent 5 on the pre-assembled bolts fixed on step 7a.
Assembly Instructions Step 10 2 Put the washers L between the lid handle 2 and the lid of the grill assembly 1 . L L Align the holes and fix the lid handle 2 on the lid of the grill assembly 1 using 10mm bolts E . E E Fix the bolts tightly by the screwdriver. 1 Step 11 Assemble the side table front support 19 and the side table rear support 20 to the side table 18 . Secure the supports with 10mm screws K .
Assembly Instructions Step 12 Install the side table assembly made in step 11 to the upper support 14 by 15mm shoulder bolts I . 14 I I I 18 I Step 13 Install the side burner assembly 21 to the upper support 14 using 15mm bolts H .
Assembly Instructions Step 14 a: Fix the side burner valve on the side burner panel of the side burner assembly using 8mm bolts J . b: Put the side burner knob on the side burner assembly 21 . 22 a: 21 J J b: 21 22 c: Put the side burner 24 and the side burner electrode 23 through the hole of side burner assembly 21 .
Assembly Instructions Step 14 d: d: Align the venturi of the side burner valve. 24 against the Important: Make sure the valve tip goes into the venturi tube completely with good alignment. J Then tighten the side burner on the side burner assembly using 8mm bolt J . 24 23 Burner venturi Connect the electrode of the main burner and the side burner electrode 23 to the electrode end of ignitor on the control panel assembly 15 .
Assembly Instructions Step 15 Put the cooking grill 3 and the warming rack 4 on the grill assembly 1 . 4 3 1 Step 16 Attach the front canvas 16 to the left front leg 11 and right front leg 9 . Secure the position with the velcro on canvas edge.
Assembly Instructions Step 17 Assembly is complete. If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800.
Technical Specification Model Number KS12012 Gas Category I3P (37) Type of Gas Propane Gas Pressure 37 mbar Pin Number 359/BU/1015 Injector Size (Main Burner) 0.84mm Injector Size (Side Burner) 0.74mm Total Heat Input 13.9 kW 4 Burner Heat Input 11.6 kW Side Burner Heat Input 2.3 kW Gas Consumption 992 g/h Country of Destination GB and IE Do not use this barbecue outside England and Ireland.
Troubleshooting Problem Burner will not light using the ignition system Possible Cause Solution LP gas cylinder is empty Replace with full cylinder Faulty regulator Have regulator checked or replace Obstructions in burner Clean burner Obstructions in gas jets or gas hose Clean jets and gas hose Electrode wire is loose or disconnected Reconnect wire on electrode or ignition unit.
