Triple Metal And Polycotton Wardrobe Assembly lnstructions - Please keep for future reference 343/6004 356/0970 Dimensions Width - 147cm Depth - 54cm Height - 175cm Important - Please read these instructions fully before starting assembly If you need help or have damaged or missing parts,call the Customer helpline：0345 6400800 Issue 1-11/03/14
! Safety and Care Advice Important - Please read these instructions fully before starting assembly components and tools listed on page 2. plastic bags and separate them into their groups. Assemble the unit as close to its final position (in the same room) as possible. Warning: Assemble on a soft level surface cables. to avoid damaging the unit or your floor. and responsibly. Warning: Short hanging rail - 10 kg Long hanging rail - 15 kg space to layout the parts before starting could cause damage.
Components - Parts If you need help or have damaged or missing parts,call the Customer helpline：0345 6400800 Please check you have all the parts listed below 1 Shelf x 1(67.5x53.4cm) 5 Thin rods x 2(86.4cm) 9 Connector x 4 2 6 Shelf x 2(40x54cm) Thin rods x 24(28.2cm) 10 Hook x 1 3 Thin rods x 5(50cm) 7 Thin rods x 3(67.5cm) 11 T-Connector x 2pcs 15 Thin rods x 1(69cm) 18 Thin rods x 2(87.7cm) locking pin 16 Thin rods x 1(42.5cm) 19 Shelf x 1(40x54cm) Thin rods x 2(82.
Assembly Instructions Step 1 Note:It would be useful to ask someone to help you at this stage. 2 a: 1 2 a: Attach shelf into shelf 2 as shown in the figure. 1 Note: Make sure the shelf panel with yellow dot face upwards ! b: Insert vertical rods 6 into shelf 2 as shown. ! b: 6 1 6 6 2 c: Attach shelf 13 to vertical rods 6 Then insert vertical rods 6 and repeat for other shelf 13 .
Assembly Instructions Step 2 a: Attach thin rods 4 and 18 to shelf 2 as shown in the figure. 18 a: 6 6 4 18 6 13 4 6 2 13 1 2 b: Insert thin rods 3 into T-connector 11 Attach assembled thin rods 3 to thin rods 4 . b: 11 3 11 18 3 18 4 4 13 13 c: Attach thin rods 15 and 16 and hook 10 . Then insert the assembled unit into shelf 19 .
Assembly Instructions Step 3 a: Attach assembled shelf 19 to thin rod 6 and thin rods 3 as shown in the figure. Then repeat step1c for the other two shelves 13 assembly. 6 6 6 13 a: 13 18 3 15 19 18 4 4 13 13 17 b: Insert thin rods 5 to T-connector 11 and insert thin rods 17 to thin rods 18 as shown in the figure. 5 6 b: 6 6 5 17 15 4 c: Insert thin rods 3 , 7 , 20 to connector 8 and 9 as shown in the figure.
Assembly Instructions Step 4 a: Attach assembled top frame to thin rod 6 and thin rods 5 17 as shown in the figure. 17 a: 6 5 6 17 5 b: Insert thin rods 7 and 20 into hook 12 . 12 7 b: 12 20 12 12 3 c: Attach assembled hanging rod to thin rods 3 as shown in the figure.
Assembly Instructions Step 5 a: Fitting the cover 14 into assembled frame as shown in the figure. a: Note: It is recommended that two people fit the cover to the frame. 14 b: b: Fasten the ties at bottom.
Assembly Instructions Step 5 Fixing to wall A wall It is recommended that the wardrobe is fixed to a wall. Note: The correct type of fixing must be used for your wall,seek professional advice if doubt. B Top panel Mark the fixing hole on the wall and remove the wardrobe. Drill a hole and insert a wall plug B . ! Warning: Before drilling, check the wall for hidden pipes and cables. Reposition the wardrobe and fix the wall strap using screw A . The assembly is now complete.
