Kensington - 5 Drawer Chest Assembly Instructions - Please keep for future reference 397/6337 392/6648 Dimensions Width - 48.5cm Depth - 39.4cm Height - 118.7cm MADE IN BRITAIN Important - Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928.
Safety and Care Advice Important - Please read these instructions fully before starting assembly • Warning: This unit weighs approximately 37kgs. Please lift with care. • Make sure you have enough space to layout the parts before starting. • Check you have all the components and tools listed on pages 2 and 3. • Do not stand or put weight on the product, this could cause damage. • Remove all fittings from the plastic bags and separate them into their groups.
Components - Panels If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Please check you have all the panels listed below 3 Top (DF2403) (70.8 x 39.4cm) 1 Left Side (DF3754) (117.2 x 37.4cm) 2 Right Side (DF3755) (117.2 x 37.4cm) 4 Rail (DF2406) (64.6 x 9.
Components - Fittings If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Assembly Instructions Step 1 A Prepare the 5 drawer fronts Screw 2 metal dowels A into each of the drawer fronts 7 . A A x5 7 Note: Tighten the metal dowels up fully against the panels. Step 2 Prepare the drawer sides C Insert a small locking nut C into the hole shown on the left drawer side 8 and the right drawer side 9 . C C Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Assembly Instructions Step 4 Fit the drawer base x5 11 Slide the drawer base 11 down the grooves in the drawer sides 8 and 9 and down into the groove in the drawer front 7 . 9 8 7 Step 5 Fit the drawer back Fit the drawer back 10 between the drawer sides 8 and 9 . Make sure that the drawer base 11 fits into the groove in the drawer back 10 . Hold the drawer back 10 in position and tap the knock-in pegs F through the holes in the drawer sides 8 and 9 .
Assembly Instructions Step 8 J Prepare the left side M a: Place 5 runners M on the left side 1 as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw J . J Finished front edge J M J M J b: Slide the runner M back the other way and fit the 2nd screw J into the corresponding hole in the left side 1 . J M 1 M a: M c: Screw 8 metal dowels A into the left side 1 . Insert 2 large locking nuts B into the left side .1 .
Assembly Instructions Step 9 J Prepare the right side M a: Place 5 runners M on the right side 2 as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw J . b: Slide the runner M back the other way and fit the 2nd screw J into the corresponding hole in the right side 2 . J J J J J a: 2 M M M M Finished front edge M c: Screw 8 metal dowels A into the right side 2 . J J J Insert 2 large locking nuts B into the right side 2 .
Assembly Instructions Step 10 Prepare the 8 rails B D B Insert 2 large locking nuts B into each of the 8 rails 4 . x8 4 Tap 2 wooden dowels D into each of the 8 rails 4 . Step 11 Fit 5 of the rails to the right side D A B Push 5 rails 4 onto the right side 2 . 2 Use a screwdriver to tighten the large locking nut B fitted to each of the rails 4 . 4 4 4 4 Note: Turn the large locking nuts B as far as they will go - more than 1/2 a turn.
Assembly Instructions Step 13 Fit the left side Push the left side 1 onto the rails 4 . 4 Use a screwdriver to tighten the large locking nut B fitted to each of the rails 4 . 4 4 4 4 4 4 1 4 4 A Step 14 A Prepare the top Screw 4 metal dowels A into the top 3 .
Assembly Instructions Step 15 Polystyrene block Fit the top Note: To make it easier to fit the top and plinths, place polystyrene blocks from the packaging underneath the side panels to raise the assembly. 3 2 Push the top 3 onto the assembly. 1 Polystyrene block Use a screwdriver to tighten the 2 large locking nuts B fitted to each of the sides 1 and .2 .
Assembly Instructions Step 17 Fit the 4 plastic nails Tap 2 plastic nails L into the bottom edge of each of the sides 1 and .2 . L 2 L L 1 L Step 18 B Prepare a side plinth Insert a large locking nut B into 1 of the side plinths 6 . Finished top edge 6 D Tap a wooden dowel D into the side plinth 6 . Step 19 Prepare the other side plinth Insert a large locking nut B into the side plinth .6 . Tap a wooden dowel D into the side plinth 6 .
Assembly Instructions A Step 20 Prepare the front plinth A Profiled top edge Screw 2 metal dowels A into the front plinth 5 . 5 Step 21 Finished top edge Fit the plinths together 6 Push the 2 side plinths 6 onto the front plinth 5 . Finished top edge Profiled top edge Use a screwdriver to tighten the large locking nuts B fitted to the side plinths 6 .
Assembly Instructions Step 23 Fix the front plinth Secure the front plinth 5 through the rail 4 using screw G . Carefully stand the unit up for the next step. G Warning: The unit is heavy. Lift with care. 4 5 Step 24 Fit the drawers Starting with the bottom drawer, slide both the runners M forward and locate the drawer sides 8 and 9 between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners M .
Assembly Instructions Step 24 O Strap O Screw Washer Strap Washer IT Wall fixing (not supplied) Attach the strap to the unit N To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by fitting of the overbalance protector kit .O to the unit, or an alternative fixing method of your choice. Attach the strap to the wall U Fit the overbalance protector kit Example Screw (not supplied) Wall fixings are not supplied as they will need to suit the wall type.
ALR3180
