New Pagnell Bedside Chest 608/8600 Assembly Instructions - Please keep for future reference 612/7475 621/4175 Dimensions Width - 40cm Depth - 40.5cm Height - 52.
Safety and Care Advice Important – Please read these instructions fully before starting assembly • Check you have all the components and tools listed on the following pages. • Remove all fittings from the plastic bags and separate them into their groups. • Keep children and animals away from the work area, small parts could choke if swallowed. • Make sure you have enough space to layout the parts before starting. • Do not use this item if any components are missing or damaged.
Components - Panels If you have damaged or missing components, call the Customer Helpline: Argos = 0345 6400800 Please check you have all the panels listed below 4 Bottom panel (36.7 x 11cm) 1 10 Drawer back panel x 3 (33.5 x 11.5cm) Top panel (40 x 40cm) 5 Bottom support (36.7 x 11cm) Finished front edge 6 Front panel 11 Drawer bottom panel x 3 (34.4 x 33.6cm) (36.7 x 4.5cm) 7 Pilot holes for guidance only 2 Drawer front panel x 3 (36 x 14.4cm) Right side panel (38 x 50.
Components - Fittings Note: The quantities below are the correct amount to complete the assembly. In some cases mor may be supplied than are required.
Assembly Instructions Step 1 a: Attaching runners a: Position Runners A front edge of the Right side panel 2 . 2 Middle hole A in B A Slide top of the Runners A . 1.7cm A B A B Runners A on the Right side panel 2 . B B Note: The front part of the runner should be approximately 1.7cm from the front edge of the panel. 2 Pilot holes for runner position Finished front edge b: Slide top of Runners A forward and B b: B 2 Middle hole A . Insert Dowels D into the Right side panel 2 .
Assembly Instructions Step 1 - continued c: Position Runners A front edge of the Left side panel 3 . in c: Slide top of the Runners A . 3 Middle hole B A 1.7cm B B Runners A on the Left side panel 3 . B B Note: The front part of Finished front edge the runner should be approximately 1.7cm from the front edge of the panel. A A A 3 Pilot holes for runner position d: Slide top of Runners A forward and B d: 3 Middle hole B A . Insert Dowels D into the Left side panel 3 .
Assembly Instructions Step 2 Fitting dowels D Insert Dowels D into the Bottom panel 4 and Bottom support 5 . 4 D D 5 D Step 3 Attaching plastic supports a: a: F F F Plastic supports E onto the Front panel 6 . E F E E 6 b: F Front panel 6 onto the Bottom panel 4 .
Assembly Instructions Step 4 Attaching bottom panel and bottom support a: G a: Position Bottom panel onto the Left side panel 3 . 4 Insert Locking nuts G into the Bottom panel 4 . back edge Use a screwdriver to turn Locking nuts G clockwise to lock. 3 4 G b: Position Bottom support 5 onto the Left side panel 3 . b: G Insert Locking nuts G into the Bottom support 5 . Use a screwdriver to turn Locking nuts G clockwise to lock.
Assembly Instructions Step 5 Attaching right side panel G Position Right side panel 2 onto the unit. Insert 2 Locking nuts G into the Bottom panel 4 and Bottom support 5 . Use a screwdriver to turn Locking nuts G clockwise to lock. 2 5 G 4 G Step 6 Attaching top panel a: C a: Screw Locking pins C into the Top panel 1 . C Note: Insert locking pins as far as shown. Do not over tighten. C C C 1 Continued on next page.
Assembly Instructions Step 6 - continued b: Carefully locate the Top panel unit. 1 b: G onto the Insert 4 Locking nuts G into the Right side panel 2 and Left side panel 3 . Use a screwdriver to turn Locking nuts G clockwise to lock. 1 G 2 G 3 Step 7 H H Fixing back panel Attach Back panel 12 onto the unit using Nails H . Important: The unit MUST be ‘square’ when back is attached.
Assembly Instructions Step 8 Drawers assembly a: a: Screw Locking pins C into 4 holes shown on back of the Drawer front panel 7 . C C C C Note: Insert Locking pins 7 as far as shown. Do not over tighten. b: Fix Drawer left side panel 9 onto the Drawer front panel 7 . C b: 9 7 c: Fix Drawer right side panel 8 onto the Drawer front panel 7 . Insert 2 Locking nuts I into the holes (they will only insesrt one way). c: I 8 Use a screwdriver to turn Locking nuts I clockwise to lock.
Assembly Instructions Step 8 - continued d: Insert 2 Locking nuts I into the holes (they will only insert one way). d: L back surface Use a screwdriver to turn Locking nuts I clockwise to lock. I 11 Place a small amount of Glue L into the grooves. Carefully slide the Drawer bottom panel 11 into the grooves. I I 8 9 L 7 e: Place a small amount of Glue L into the groove on the Drawer back panel 10 . e: f: Position the Drawer f: onto the unit using Screws J .
Assembly Instructions Step 9 Inserting drawers a: With help, carefully stand deawer chest upright. Warning: The drawer chest is heavy. Lift with care. K K K a: Slide the drawers fully onto the runners so the runners butt up against the back of the drawer front. K K K K b: b: Fix through drawer sides into the runners using Screws K . Step 10 Finishing the unit With help, place the unit in the intended position. Note: Before use allow glue to dry for 24 hours and make sure the unit is secure.
