New Pagnell Deep 3+2 Chest Assembly Instructions - Please keep for future reference 610/8793 620/5861 619/5139 Dimensions Width - 76.5cm Depth - 40.
Safety and Care Advice Important – Please read these instructions fully before starting assembly • Check you have all the components and tools listed on the following pages. • Remove all fittings from the plastic bags and separate them into their groups. • Keep children and animals away from the work area, small parts could choke if swallowed. • Make sure you have enough space to layout the parts before starting. • Do not use this item if any components are missing or damaged.
Components - Panels If you have damaged or missing components, call the Customer Helpline: Argos = 0345 6400800 Please check you have all the panels listed below 9 Small drawer left panel x 4 10 Small drawer right panel x 4 11 Large drawer left panel (34 x 24cm) 12 Large drawer right panel (34 x 24cm) (34 x 11.5cm) (34 x 11.5cm) Pilot holes for guidance only 1 Left side panel (80.4 x 38cm) Finished front edge Drill holes near edge Pilot holes for guidance only 2 Right side panel (80.
Components - Fittings Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required. A 50mm Screw x 2 D B C 30mm Screw x 22 39mm Locking pin x 33 F E 15mm Locking nut x 12 30mm Dowel x 9 Nail x 18 G H 12mm Locking nut x 21 12mm Screw x 10 I 14.
Assembly Instructions Step 1 a: Attaching runners a: Position Runners K front edge of the Right side panel 2 . in 2 Middle hole K Slide top of the Runners K back. L K 1.7cm K Use screws L to fix the Runners K on the Right side panel 2 . L K L K L Note: The front part of L the runner should be approximately 1.7cm from the front edge of the panel.
Assembly Instructions Step 1 - continued c: Position Runners K in front edge of the Left side panel 1 . c: 1 Middle hole L K Slide top of the Runners K back. Use screws L to fix the Runners K on the Left side panel 1 . L 1.7cm L L Note: The front part of the runner should be approximately 1.7cm from the front edge of the panel. K K L Finished front edge K K Pilot holes for runner position 1 d: Slide top of Runners forward and fix as shown using Screws L .
Assembly Instructions Step 1 - continued e: e: Position Runner K in front edge of the Top support 3 . 3 Middle hole L K Slide top of the Runner K back. Use screw L to fix the Runner K on the Top support 3 . L 1.7cm Finished front edge Note: The front part of the runner should be approximately 1.7cm from the front edge of the panel. 3 K Pilot holes for runner position f: f: Slide top of Runner forward and fix as shown using Screws L .
Assembly Instructions Step 2 a: Attaching plastic supports I I a: Use Screws I to fix Plastic supports the Front panel J 7 onto . I I J J J 7 J b: Use Screws to fix Front panel 7 onto the Front bottom panel 6 . I b: I D I I 7 I 6 D Step 3 Attaching bottom panel and middle panel D a: a: Insert Dowels D into the Back bottom panel 5 . 5 D b: lnsert Dowels D into the Middle panel 4 . b: Use Screws A to fix the Top support 3 onto the Middle panel 4 .
Assembly Instructions Step 3 - continued c: Carefully locate the Middle panel 4 onto the Left side panel 1 . c: F Insert Locking nut F into the Middle panel 4 . Use a screwdriver to turn Locking nut F clockwise to lock. Unfinished back edge 1 4 F d: Carefully locate the Front bottom panel onto the Left side panel 1 . 6 d: F Insert Locking nut F into the Front bottom panel 6 . Unfinished back edge Use a screwdriver to turn Locking nut F clockwise to lock.
Assembly Instructions Step 3 - continued e: Carefully locate the Back bottom panel 5 onto the Left side panel 1 . e: F Insert Locking nut F into the Back bottom panel 5 . Unfinished back edge Use a screwdriver to turn Locking nut F clockwise to lock. 1 5 F Step 4 Unfinished back edge Attaching right side panel Carefully locate the Right side panel 2 onto the unit. Insert 3 Locking nuts into the unit. F 4 5 Use a screwdriver to turn Locking nuts F clockwise to lock.
Assembly Instructions Step 5 a: Attaching top panel a: Screw Locking pins C into the Top panel 8 C . C Note: Insert locking pins as far as shown. Do not over tighten. C C C C C 8 b: Then carefully locate the Top panel 8 onto the unit. Insert 6 Locking nuts into the unit. b: F F Use a screwdriver to turn Locking nuts F clockwise to lock.
Assembly Instructions Step 6 Fixing back panel E Attach Back panel onto the unit using Nails E . 23 Unfinished back surface Important: The unit MUST be ‘square’ when back is attached. 23 Step 7 Large drawer assembly a: C a: Screw Locking pins C into the Large drawer front panel 16 . C Note: Insert locking pins C as far as shown. Do not over tighten. C C C Continued on next page.
Assembly Instructions Step 7 - continued b: Fix the Large drawer left panel 11 , Large drawer right panel 12 and Large drawer support 20 onto the Large drawer front panel 16 . b: G Insert Locking nuts G into the holes (they will only insert one way). Use a screwdriver to turn Locking nuts G clockwise to lock. G 11 G 20 12 16 G G G c: Place a small amount of Glue O into the grooves. c: Unfinished back surface Carefully slide the Large drawer bottom panel 22 into the grooves.
Assembly Instructions Step 7 - continued d: Place a small amount of Glue O onto the Large drawer bottom panel 22 . B d: B B 19 Position the Large drawer back panel 19 onto the unit using Screws B . O 22 B B 12 Step 8 Middle drawer assembly C a: C C a: Screw Locking pins into the Middle drawer front panel 15 . C C Note: Insert locking pins C 15 X2 as far as shown. Do not over tighten.
Assembly Instructions Step 8 - continued c: Place a small amount of Glue O into the grooves. Unfinished back surface c: O Carefully slide the Large drawer bottom panel 22 into the grooves. 22 15 10 d: Place a small amount of Glue O onto the Large drawer bottom panel 22 . O X2 d: B Position the Middle drawer back panel 18 onto the unit using Screws B .
Assembly Instructions Step 9 - continued b: Fix the Small drawer left panels 9 and Small drawer right panels 10 onto the Left drawer front panel 13 and Right drawer front panel 14 . b: G Insert Locking nuts G into the holes (they will only insert one way). G 9 Use a screwdriver to turn Locking nuts G clockwise to lock. 9 G 10 G G 10 Drill holes near edge G c: Carefully slide the Small drawer bottom panels into the grooves.
Assembly Instructions Step 8 10 Fixing to wall Note: Wall plugs supplied are for solid wall only. wall N M Warning: In order to prevent overturning, this product must be used with the wall attachment device provided. Use Screws(2 pcs) I to fix Wall straps(2 pcs) M onto the unit. be used for your wall, seek professional advice if in doubt M I M M N Top panel With help, move this product into position. Warning: Back panel This product is heavy. Lift with care.
Assembly Instructions Step 11 Inserting drawers a: Pull runners out. Slide drawers onto runners so they butt up against back of drawer front. a: 8 13 Side panel near the edge. (Left side small drawer) 14 Side panel near the edge. (Right side small drawer) b: Fix through drawer sides into runners using screws H . 8 H 14 H H 13 15 H 15 H H b: H Assembly is complete.
A Guide to - Wall Mounting & Fixings Important: When drilling into walls always Important note: If plastic wall plugs are supplied with your product: check that there are no hidden wires or pipes etc. Make sure that the screws and wall plugs being used are suitable for supporting your unit. Consult a qualified tradesperson if you are unsure. Hints: - these are only suitable for use in masonry walls. If you are in any doubt about the correct wall plugs for your wall, seek professional advice.
