Seville - 3 Door Robe Assembly Instructions - Please keep for future reference 147/4556 171/6939 167/8338 173/6146 Dimensions Width - 102.5cm Depth - 49.5cm Height - 175.5cm MADE IN BRITAIN Important - Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.
Safety and Care Advice Important - Please read these instructions fully before starting assembly • Warning: This unit weighs approximately 59kgs. Please lift with care. • Make sure you have enough space to layout the parts before starting. • Check you have all the components and tools listed on pages 2 and 3. • Do not stand or put weight on the product, this could cause damage. • Remove all fittings from the plastic bags and separate them into their groups.
If you have damaged or missing components, call the Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number Components - Panels and the reference numbers below) Please check you have all the panels listed below 1 Left Side (D2483A) (1753 x 496mm) 2 Right Side (D2497A) (1753 x 496mm) 3 Upright (D2500A) (1640.
Components - Fittings If you have damaged or missing components, call the Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number and the reference numbers below) Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Assembly Instructions If you have damaged or missing components, call the Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number and the reference numbers below) Step 1 A Prepare the top and base 4 Tap 2 wooden dowels A into the top 4 . Finished front edge Tap 2 wooden dowels A into the base 5 . A A in la p 10mm d ar o b ip ch Note: Wooden dowels must not stick out from the edge by more than 10mm or they may damage other panels.
Assembly Instructions Step 3 Fit the top and the base to the upright C Fit the top 4 and the base 5 onto the upright . 3 using 4 screws C . C 4 3 pla C in c Finished front edge Finished front edge hip bo ard 5 sur fac e C Finished front edge Step 4 L Prepare the right side Fit 3 hinge plates L onto the right side 2 , making sure that the slot is facing towards the finished front edge.
Assembly Instructions Step 5 C Fit the right side C Push the right side 2 onto the top 4 and base 5 and secure it using 4 screws C . 4 2 C C 5 Step 6 A Prepare the plinth Plain chipboard Tap 2 wooden dowels A into the plinth 6 . 6 A Step 7 Prepare the left side Push a rail holder H into the left side 1 . Make sure that it is fitted straight, in line with the panel edges and then secure with screw F .
Assembly Instructions Step 8 Fit the plinth Push the plinth 6 onto the right side 2 and secure it using screw C . 2 C 6 Note: Support the plinth until the left side has been fitted in the next step. Step 9 Fit the left side Push the left side 1 onto the assembly and secure it using 5 screws .C .
Assembly Instructions Step 10 a: Fit the back a: Square up the unit by making sure that measurement x to x equals y to y. Place the small back 10 and large back 11 down onto the unit as shown. Make sure that the 2 backs are pushed up tight against each other and that they meet over the back edge of the upright. The measurement from top corner X to bottom corner X must be equal to the measurement from top corner Y to bottom corner Y b: x B y 10 11 y b: Note: Do not nail where the backs meet.
Assembly Instructions Step 12 Fit the hanging rail and the shelves 8 Push hanging rail 8 into the rail holders H fitted to the side panels. H For each of the 2 shelves 7 , insert 4 shelf studs E at the required height. 8 7 E x4 Lower the 2 shelves 7 down onto the shelf studs L . 7 E x4 Make sure that the plastic sleeve is fully pushed onto the shelf stud. E Step 13 F Prepare the 3 doors Push fit 3 hinges M into each of the the doors 9 F F . M x3 F Secure each hinge with 2 screws F .
Assembly Instructions Step 14 a: L Fit doors and handles M A onto the front part of the hinge plate L . The recess at the bottom of screw B goes into the slot in the hinge plate. b: Keep the hinge M B c: L M M Note: The easiest way to attach each door 9 is to fit the top hinge first, then align and fit the other hinges. a: Push the hinge b: L d: L L M M B M FLAT against the hinge plate L as you slide it across as far as it will go. Tighten screw A.
Assembly Instructions Step 15 Adjust the doors if needed a: a: Before adjusting the doors, use a spirit level to check the base (or top) of the unit is level, front-to-back and side-to-side in the 3 positions shown. Use suitable packing pieces (not supplied) to make the unit level BEFORE making any adjustment to the hinges, as shown. b: A A b: Height adjustment. Loosen screws A on hinge plates and move door up or down as required. Retighten screw A. c: B c: Forward and Back adjustment.
Assembly Instructions Step 16 Wall fixings are not supplied as they will need to suit the wall type. Strap Washer I Strap F Screw (not supplied) U N IT Washer O Wall fixing (not supplied) Screw I P To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by fitting of the overbalance protector kit . I to the unit, or an alternative fixing method of your choice.
ALR2909
